Posted: Tue Jul 14, 2020 22:08 Post subject: Can't set local ip address
Router/Version: Linksys wrt320n
Previous/Reset: 43718, yes
Issues/Errors: The router won't take a new local IP address. The steps below work in 43718. Also, after setting Local IP Address and clicking Save, the autopopulated octets in Start IP Address no longer default to the octets set in Local IP Address.
Steps to reproduce:
Set Local IP Address
Unplug/replug eth cable
Connect to new IP in browser Unsuccessful
PING: transmit failed. General failure.
Last edited by mastaofdisastax on Tue Jul 21, 2020 6:41; edited 1 time in total
Joined: 08 May 2018 Posts: 6944 Location: Texas, USA
Posted: Tue Jul 14, 2020 23:11 Post subject:
you have had to have done something different to get those channels. no one else with the r7000p has them
Here's the gory details:
I bought it brand new from Wal-Mart. I flashed 40270M kongac to it. WebUI reset. I tried configuring client bridge, repeater bridge, and repeater, all of which boot-looped. Got it reset after that mess, set 2.4 radio as client, 5GHz as AP. Been the same configuration since then. Flashed 43516 without reset. Flashed 43812 test build without reset. I *just* did the nvram set and commit and reboot earlier. I also have not used anything but FF ESR or IE to access it, save and except when testing to see if Chromium-based browsers were still problematic after flashing 43516. The damn thing only runs part of one of my test benches in my shop, and is only fired up when I actually need to use it... and I only recently decided to upgrade it to BS builds. Could it be possible there's more than one revision of this device? Could it be the version of Netgear firmware that was installed when I flashed 40270M? No idea. But I promise you, I'm not withholding anything, no tricks up my sleeve, not yanking your chain, etc.
Router Model: Netgear R8000
Firmware Version: DD-WRT v3.0-r43800 std (07/14/20)
Kernel Version: Linux 4.4.230 #564 SMP Tue Jul 14 08:44:05 +04 2020 armv7l
Uptime: 35 min
Previous: DD-WRT v3.0-r43718 std (07/09/20)
Upgrade: via webgui
Services: samba, wireguard client, openvpn client, dhcp, wifi 2.4 Ghz
Load Average: 0.21, 0.58, 1.21
Temperatures: CPU 51.4 °C
Issue: difficulty in surfing the web. Constantly enabling or disabling dhcp-authorative, recursive dns resolving (unbound), forced dns redirection while maintaining sfe always enabled. Web pages may or may not load, cannot connect to amazon, Netflix, etc.
Errors: as shown from the syslog
Dec 31 20:00:19 DD-WRT local5.err ksmbd: [ksmbd-worker/1206]: ERROR: Can't open `/tmp/smb.db': No such file or directory
Dec 31 20:00:19 DD-WRT local5.err ksmbd: [ksmbd-worker/1206]: ERROR: User database file does not exist. Only guest sessions (if permitted) will work.
Dec 31 20:00:19 DD-WRT user.err wsdd2: error: wsdd-mcast-v4: wsd_send_soap_msg: send
Dec 31 20:00:25 DD-WRT user.err wsdd2: Terminated received.
Dec 31 20:00:28 DD-WRT daemon.err ntpclient: Failed resolving address to hostname 2.pool.ntp.org: Try again
Dec 31 20:00:28 DD-WRT daemon.err ntpclient: Failed resolving server 2.pool.ntp.org: Network is down
Jul 14 18:55:32 DD-WRT local5.err ksmbd: [ksmbd-manager/2277]: ERROR: Failed to create lock file: File exists
Jul 14 18:58:43 DD-WRT user.err wsdd2: Terminated received.
Jul 14 18:58:45 DD-WRT local5.err ksmbd: [ksmbd-worker/2827]: ERROR: Can't open `/tmp/smb.db': No such file or directory
Jul 14 18:58:45 DD-WRT local5.err ksmbd: [ksmbd-worker/2827]: ERROR: User database file does not exist. Only guest sessions (if permitted) will work.
Jul 14 19:02:41 DD-WRT user.err wsdd2: error: wsdd-mcast-v4: open_ep: IP_ADD_MEMBERSHIP
Jul 14 19:02:41 DD-WRT user.err wsdd2: error: wsdd-http-v4: open_ep: SO_BINDTODEVICE
Jul 14 19:02:49 DD-WRT user.err wsdd2: error: wsdd-mcast-v4: wsd_send_soap_msg: send
Jul 14 19:07:34 DD-WRT local5.err ksmbd: [ksmbd-manager/5599]: ERROR: WARNING: child process exited abnormally: 5600
Jul 14 19:07:34 DD-WRT daemon.err httpd: httpd : Request Error Code 408: Unexpected connection close in intitial request
Jul 14 19:13:47 DD-WRT daemon.err dnsmasq: failed to send packet: Network unreachable
Posted: Wed Jul 15, 2020 5:38 Post subject: I'm having the 5G issue as well
I have 2 brand new Netgear R7000p routers and when first flashed and even after reset it will show only the upper 5ghz channels under 20mhz only. When you apply 40/80mhz these disappear as the screen shots show. They do come back if you apply 20mhz though. You can choose 80mhz and a channel and apply it and it will set it but then it removes other choices so you must go back to 20mhz to get them back for some reason.
I haven't been able to get the lower channels to display no matter how much I play with it.