Here is what I get. I use static IP address as wan connection.
Ps. consider using copy/past results, and use
Code:
[code][/code]
much readable than pics.
No results: I would consider, over administration, factory default.
And for last resource: nvram erase and reboot or 30/30/30 reset.
I don´t have any experience about that on my own wrt54g. So proceed with caution before doing that.
I can see now. For some reason eth0 is missing on your configuration.
Without it, vlans don´t work.
try this:
Code:
ifconfig eth0 up
startservice lan
startservice wan
ps: to add this kind of text, select on the terminal that you are using the portion of information you wan to copy with your mouse.
Move the mouse over this box and just past over it. Use the code button on top of this box, twice, one at the start of the copied text another at the end.
Joined: 08 May 2018 Posts: 14207 Location: Texas, USA
Posted: Sun Jul 12, 2020 23:39 Post subject:
What is the WAN port setting on the main setup page? Disabled, auto-dhcp, what? Looks like you are not getting a WAN IP address. Not sure if you are configuring gateway or router / switch mode here. _________________ "Life is but a fleeting moment, a vapor that vanishes quickly; All is vanity"
Contribute To DD-WRT Pogo - A minimal level of ability is expected and needed... DD-WRT Releases 2023 (PolitePol)
DD-WRT Releases 2023 (RSS Everything)
----------------------
Linux User #377467 counter.li.org / linuxcounter.net
configured WAN as auto-dhcp and router to get DHCP from secondary router. The problem is that not even the LAN ports work. None of the ports on the router work.
In router mode, your wan would be disabled and assigned to the switch. In gateway mode, your wan would be auto-dhcp. Reset, start over. Quit beating your own head with a hammer. _________________ "Life is but a fleeting moment, a vapor that vanishes quickly; All is vanity"
Contribute To DD-WRT Pogo - A minimal level of ability is expected and needed... DD-WRT Releases 2023 (PolitePol)
DD-WRT Releases 2023 (RSS Everything)
----------------------
Linux User #377467 counter.li.org / linuxcounter.net
1) WAN in AUTO-DHCP does not get IP
2) LAN ports do not get DHCP from router
3) Setting PC ethernet to static IP does not ping router or have access to router GUI
4) WLAN has access to router GUI and get DHCP from router
What I did Next (not an ideal solution):
Set to ROUTER mode:
(This allow me to surf the internet only from LAN connections using all static
configurations, however I am not able to ping the router
at 192.168.1.1 or access the GUI from a LAN connection)
LAN IP: 192.168.1.1
SM: 255.255.255.0
1) set static WAN IP as follows:
IP: 192.168.1.222
SM: 255.255.255.0
GW: 192.168.1.254 <<<<< (This is my main gateway)
DNS: 8.8.8.8
2) Set Static IP on PC Ethernet:
IP: 192.168.1.223
SM: 255.255.255.0
GW: 192.168.1.254 (192.168.1.1 will not work)
DNS: 8.8.8.8
3) WLAN client will get an IP from DHCP and access the GUI but will not be able to surf the internet.
4) LAN clients will not get DHCP or ping the router
Joined: 08 May 2018 Posts: 14207 Location: Texas, USA
Posted: Mon Jul 13, 2020 2:19 Post subject:
Ok, how is your router and network connecting to the internet? I need a larger picture, because you are not giving all details here. Are you connecting to a cable modem, a *DSL modem, what. This is dragging a possibly simple solution out a little bit far. Draw a picture, if you must. _________________ "Life is but a fleeting moment, a vapor that vanishes quickly; All is vanity"
Contribute To DD-WRT Pogo - A minimal level of ability is expected and needed... DD-WRT Releases 2023 (PolitePol)
DD-WRT Releases 2023 (RSS Everything)
----------------------
Linux User #377467 counter.li.org / linuxcounter.net
I have an existing network with an internet gateway at 192.168.1.254 running a wired DHCP. This gateway is connected to a switch. This old linksys router would be a secondary router running on an existing network.
But Forget the WAN port and accessing the internet,
The problem here is even before connecting this router to the network, I just want to be able to access the router and the GUI via the LOCAL LAN ports as this has been impossible to do. The only way I am able to access the router is via a Wireless connection. So in essence here, the issue is that the LAN PORTS do not route to the GUI or LAN IP address.
Thanks.