RB1000 OpenVPN server issues

Post new topic   Reply to topic    DD-WRT Forum Forum Index -> ARM or PPC based Hardware
Goto page Previous  1, 2, 3  Next
Author Message
kernel-panic69
DD-WRT Guru


Joined: 08 May 2018
Posts: 8963
Location: Texas, USA

PostPosted: Fri Jul 03, 2020 20:55    Post subject: Reply with quote
That is not from the serial console, is it? Copy and paste the entire syslog and serial console log into a text file and attach.
_________________
Official Forum Rules, Guidelines & Helpful InformationFirmware FAQInstallation WikiWhere Do I Download Firmware?
DON'T use Chromium-based browsersRTFM/STFW TL;DR is NOT an excuse. • Why Should I Care What Color the Bikeshed Is?
Please DO NOT PM me with questions; Ask in the forum. ---------------------- Linux User #377467 counter.li.org / linuxcounter.net
Sponsor
GIENEK_II
DD-WRT Novice


Joined: 18 Jun 2020
Posts: 21

PostPosted: Fri Jul 03, 2020 20:57    Post subject: Reply with quote
tomorrow i do it
yes its from /var/log/messages
kernel-panic69
DD-WRT Guru


Joined: 08 May 2018
Posts: 8963
Location: Texas, USA

PostPosted: Fri Jul 03, 2020 21:03    Post subject: Reply with quote
That is NOT the serial console. You have to attach a cable to the router and use a serial terminal application like PuTTY for that.

https://wiki.mikrotik.com/wiki/Serial_Port_Usage

https://wiki.mikrotik.com/wiki/Manual:System/Serial_Console

The serial console is NOT accessible over the network.

_________________
Official Forum Rules, Guidelines & Helpful InformationFirmware FAQInstallation WikiWhere Do I Download Firmware?
DON'T use Chromium-based browsersRTFM/STFW TL;DR is NOT an excuse. • Why Should I Care What Color the Bikeshed Is?
Please DO NOT PM me with questions; Ask in the forum. ---------------------- Linux User #377467 counter.li.org / linuxcounter.net
BrainSlayer
Site Admin


Joined: 06 Jun 2006
Posts: 7148
Location: Dresden, Germany

PostPosted: Fri Jul 03, 2020 22:28    Post subject: Reply with quote
the dmesg error means "bad opcode" thats all what i can say at the current time. need to check if my compiler settings are correct
_________________
"So you tried to use the computer and it started smoking? Sounds like a Mac to me.." - Louis Rossmann https://www.youtube.com/watch?v=eL_5YDRWqGE&t=60s
BrainSlayer
Site Admin


Joined: 06 Jun 2006
Posts: 7148
Location: Dresden, Germany

PostPosted: Sat Jul 04, 2020 7:26    Post subject: Reply with quote
i will provide a new testimage here in some minutes/hours for the rb1000. i have a idea for the cause
_________________
"So you tried to use the computer and it started smoking? Sounds like a Mac to me.." - Louis Rossmann https://www.youtube.com/watch?v=eL_5YDRWqGE&t=60s
BrainSlayer
Site Admin


Joined: 06 Jun 2006
Posts: 7148
Location: Dresden, Germany

PostPosted: Sat Jul 04, 2020 8:23    Post subject: Reply with quote
rb1000 test image
_________________
"So you tried to use the computer and it started smoking? Sounds like a Mac to me.." - Louis Rossmann https://www.youtube.com/watch?v=eL_5YDRWqGE&t=60s
BrainSlayer
Site Admin


Joined: 06 Jun 2006
Posts: 7148
Location: Dresden, Germany

PostPosted: Tue Jul 07, 2020 11:39    Post subject: Reply with quote
dont know why i provided this test image. the original author of this thread did not take care of it anymore as it seems
_________________
"So you tried to use the computer and it started smoking? Sounds like a Mac to me.." - Louis Rossmann https://www.youtube.com/watch?v=eL_5YDRWqGE&t=60s
GIENEK_II
DD-WRT Novice


Joined: 18 Jun 2020
Posts: 21

PostPosted: Sat Jul 11, 2020 18:21    Post subject: Reply with quote
BrainSlayer wrote:
dont know why i provided this test image. the original author of this thread did not take care of it anymore as it seems

Code:



RouterBOOT booter 6.47

RouterBoard 1000

CPU frequency: 1333 MHz
  Memory size: 512 MiB
    NAND size:  64 MiB

Press any key within 2 seconds to enter setup..
Booting CF
Loading kernel... done
setting up elf image... OK
jumping to kernel code
[    0.000000] Using RB1000 machine description
[    0.000000] Memory CAM mapping: 256/256 Mb, residual: 0Mb
[    0.000000] Linux version 3.10.108-d10 (root@linux) (gcc version 5.4.0 (LEDE GCC 5.4.0 r3143-e982c4b) ) #3824 Sat Jun 13 11:10:59 +04 2020
[    0.000000] bootconsole [udbg0] enabled
[    0.000000] Zone ranges:
[    0.000000]   DMA      [mem 0x00000000-0x0effffff]
[    0.000000]   Normal   [mem 0x0f000000-0x1fffffff]
[    0.000000] Movable zone start for each node
[    0.000000] Early memory node ranges
[    0.000000]   node   0: [mem 0x00000000-0x1fffffff]
[    0.000000] MMU: Allocated 1088 bytes of context maps for 255 contexts
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 130048
[    0.000000] Kernel command line: console=ttyS0,115200 root=/dev/sda2 rootfstype=squashfs board=mpc8343 boot=1 mlc=2 noinitrd init=/sbin/init
[    0.000000] PID hash table entries: 2048 (order: 1, 8192 bytes)
[    0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
[    0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
[    0.000000] Sorting __ex_table...
[    0.000000] Memory: 515788k/524288k available (3572k kernel code, 8500k reserved, 172k data, 155k bss, 128k init)
[    0.000000] Kernel virtual memory layout:
[    0.000000]   * 0xfffdf000..0xfffff000  : fixmap
[    0.000000]   * 0xefffe000..0xf0000000  : early ioremap
[    0.000000]   * 0xe1000000..0xefffe000  : vmalloc & ioremap
[    0.000000] NR_IRQS:512 nr_irqs:512 16
[    0.000000] mpic: Setting up MPIC " OpenPIC " version 1.2 at e0040000, max 1 CPUs
[    0.000000] mpic: ISU size: 1, shift: 0, mask: 0
[    0.000000] mpic: Initializing for 32 sources
[    0.000000] clocksource: timebase mult[f0009d5] shift[24] registered
[    0.006303] pid_max: default: 32768 minimum: 301
[    0.010881] Mount-cache hash table entries: 512
[    0.016234] NET: Registered protocol family 16
[    0.020960] Probe PCI Hardware
[    0.024106] PCI: Probing PCI hardware
[    0.032934] bio: create slab <bio-0> at 0
[    0.037287] SCSI subsystem initialized
[    0.041421] usbcore: registered new interface driver usbfs
[    0.046908] usbcore: registered new interface driver hub
[    0.052189] usbcore: registered new device driver usb
[    0.057655] Switching to clocksource timebase
[    0.062632] NET: Registered protocol family 2
[    0.067210] TCP established hash table entries: 4096 (order: 3, 32768 bytes)
[    0.074196] TCP bind hash table entries: 4096 (order: 2, 16384 bytes)
[    0.080595] TCP: Hash tables configured (established 4096 bind 4096)
[    0.086953] TCP: reno registered
[    0.090108] UDP hash table entries: 256 (order: 0, 4096 bytes)
[    0.095925] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[    0.102219] NET: Registered protocol family 1
[    0.108587] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    0.114331] msgmni has been set to 1007
[    0.118418] io scheduler noop registered
[    0.122245] io scheduler deadline registered (default)
[    0.127656] Serial: 8250/16550 driver, 2 ports, IRQ sharing enabled
[    0.134113] serial8250.0: ttyS0 at MMIO 0xe0004500 (irq = 26) is a 16550A
[    0.140804] console [ttyS0] enabled, bootconsole disabled
[    0.140804] console [ttyS0] enabled, bootconsole disabled
[    0.151939] RB_PPC CF
[    0.154218] CF: using Local-Bus clock 133332 kHz 7500 ps
[    0.159512] CF: irq level 1
[    0.162658] scsi0 : pata_rb_ppc
[    0.165925] ata1: PATA max PIO6 irq 16
[    0.169668] RB_PPC CF
[    0.171934] CF: irq level 1
[    0.174827] CF PIO mode changed to 0
[    0.178662] scsi1 : pata_rb_ppc
[    0.181922] ata2: PATA max PIO6 irq 17
[    0.186063] RB_PPC NAND
[    0.188538] NAND device: Manufacturer ID: 0xad, Chip ID: 0x76 (Hynix NAND 64MiB 3,3V 8-bit), 64MiB, page size: 512, OOB size: 16
[    0.200088] Scanning device for bad blocks
[    0.267736] Bad eraseblock 1255 at 0x00000139c000
[    0.308901] Bad eraseblock 1976 at 0x000001ee0000
[    0.420874] Creating 2 MTD partitions on "NAND 64MiB 3,3V 8-bit":
[    0.426954] 0x000000000000-0x000000400000 : "RouterBoard NAND Boot"
[    0.444077] ata1.00: CFA: SanDisk SDCFX3-2048, HDX 4.03, max MWDMA2
[    0.450327] ata1.00: 4001760 sectors, multi 0: LBA
[    0.455765] 0x000000400000-0x000004000000 : "RouterBoard NAND Main"
[    0.462216] ata1.00: configured for PIO6
[    0.466268] scsi 0:0:0:0: Direct-Access     ATA      SanDisk SDCFX3-2 HDX  PQ: 0 ANSI: 5
[    0.475101] sd 0:0:0:0: [sda] 4001760 512-byte logical blocks: (2.04 GB/1.90 GiB)
[    0.482776] sd 0:0:0:0: Attached scsi generic sg0 type 0
[    0.488160] sd 0:0:0:0: [sda] Write Protect is off
[    0.493153] sd 0:0:0:0: [sda] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
[    0.504272]  sda: sda1 sda2 sda3
[    0.508198] sd 0:0:0:0: [sda] Attached SCSI removable disk
[    0.515298] libphy: Fixed MDIO Bus: probed
[    0.519536] PPP generic driver version 2.4.2
[    0.523924] PPP BSD Compression module registered
[    0.528612] PPP Deflate Compression module registered
[    0.533659] PPP MPPE Compression module registered
[    0.538433] NET: Registered protocol family 24
[    0.542884] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    0.549468] ehci-pci: EHCI PCI platform driver
[    0.553964] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[    0.560321] usbcore: registered new interface driver usbserial
[    0.566196] usbcore: registered new interface driver usbserial_generic
[    0.572764] usbserial: USB Serial support registered for generic
[    0.578807] usbcore: registered new interface driver option
[    0.584423] usbserial: USB Serial support registered for GSM modem (1-port)
[    0.591418] usbcore: registered new interface driver pl2303
[    0.597029] usbserial: USB Serial support registered for pl2303
[    0.602990] usbcore: registered new interface driver sierra
[    0.608596] usbserial: USB Serial support registered for Sierra USB modem
[    0.615515] softdog: Software Watchdog Timer: 0.08 initialized. soft_noboot=0 soft_margin=60 sec soft_panic=0 (nowayout=0)
[    0.626991] netem: version 1.3
[    0.630033] u32 classifier
[    0.632731]     Performance counters on
[    0.636550]     input device check on
[    0.640195]     Actions configured
[    0.643584] Netfilter messages via NETLINK v0.30.
[    0.648296] nf_conntrack version 0.5.0 (8059 buckets, 32236 max)
[    0.654396] nf_conntrack_rtsp v0.7 loading
[    0.658686] nf_nat_rtsp v0.7 loading
[    0.662261] ip_tables: (C) 2000-2006 Netfilter Core Team
[    0.667607] TCP: bic registered
[    0.670733] TCP: cubic registered
[    0.674036] TCP: westwood registered
[    0.677595] TCP: highspeed registered
[    0.681241] TCP: hybla registered
[    0.684543] TCP: htcp registered
[    0.687754] TCP: vegas registered
[    0.691054] TCP: veno registered
[    0.694269] TCP: scalable registered
[    0.697828] TCP: lp registered
[    0.700866] TCP: yeah registered
[    0.704080] TCP: illinois registered
[    0.707641] NET: Registered protocol family 17
[    0.712096] Bridge firewalling registered
[    0.716094] 8021q: 802.1Q VLAN Support v1.8
[    0.724357] VFS: Mounted root (squashfs filesystem) readonly on device 8:2.
[    0.731494] Freeing unused kernel memory: 128K
init : start service
init : starting Architecture code for rb600
udevtrigger[337]: parse_config_file: can't open '/etc/udev/udev.conf' as config file: No such file or directory
[    2.214402] EXT4-fs (sda3): recovery complete
[    2.242811] EXT4-fs (sda3): mounted filesystem with ordered data mode. Opts: (null)
[    2.389145] libphy: Freescale PowerQUICC MII Bus: probed
[    2.429406] fsl-gianfar e0024000.ethernet: enabled errata workarounds, flags: 0x4
[    2.437112] fsl-gianfar e0024000.ethernet eth0: mac: 00:0c:42:20:6d:b8
[    2.443628] fsl-gianfar e0024000.ethernet eth0: Running with NAPI enabled
[    2.450398] fsl-gianfar e0024000.ethernet eth0: RX BD ring size for Q[0]: 256
[    2.457517] fsl-gianfar e0024000.ethernet eth0: TX BD ring size for Q[0]: 256
[    2.464672] fsl-gianfar e0025000.ethernet: enabled errata workarounds, flags: 0x4
[    2.472323] fsl-gianfar e0025000.ethernet eth1: mac: 00:0c:42:20:6d:b9
[    2.478833] fsl-gianfar e0025000.ethernet eth1: Running with NAPI enabled
[    2.485609] fsl-gianfar e0025000.ethernet eth1: RX BD ring size for Q[0]: 256
[    2.492727] fsl-gianfar e0025000.ethernet eth1: TX BD ring size for Q[0]: 256
[    2.499876] fsl-gianfar e0026000.ethernet: enabled errata workarounds, flags: 0x4
[    2.507536] fsl-gianfar e0026000.ethernet eth2: mac: 00:0c:42:20:6d:ba
[    2.514052] fsl-gianfar e0026000.ethernet eth2: Running with NAPI enabled
[    2.520822] fsl-gianfar e0026000.ethernet eth2: RX BD ring size for Q[0]: 256
[    2.527940] fsl-gianfar e0026000.ethernet eth2: TX BD ring size for Q[0]: 256
[    2.535092] fsl-gianfar e0027000.ethernet: enabled errata workarounds, flags: 0x4
[    2.542734] fsl-gianfar e0027000.ethernet eth3: mac: 00:0c:42:20:6d:bb
[    2.549244] fsl-gianfar e0027000.ethernet eth3: Running with NAPI enabled
[    2.556020] fsl-gianfar e0027000.ethernet eth3: RX BD ring size for Q[0]: 256
[    2.563138] fsl-gianfar e0027000.ethernet eth3: TX BD ring size for Q[0]: 256
[    2.710439] via_rhine: v1.10-LK1.5.1 2010-10-09 Written by Donald Becker
[    2.765062] tulip: Linux Tulip driver version 1.1.15 (Feb 27, 2007)
load ATH 802.11 a/b/g Driver
[    2.833625] ath_hal: module license 'Proprietary' taints kernel.
[    2.839620] Disabling lock debugging due to kernel taint
[    2.846853] ath_hal: 2009-05-08 (AR5210, AR5211, AR5212, RF5111, RF5112, RF2413, RF5413, RF2425, XR)
[    2.930302] ath_pci: trunk
[    2.933023] wlan: trunk
[    2.935456] wlan: mac acl policy registered
[    2.939623] ath_rate_sample: 1.2 (trunk)
[    2.943533] ath_rate_minstrel: Minstrel automatic rate control algorithm 1.2 (trunk)
[    2.951256] ath_rate_minstrel: look around rate set to 10%
[    2.956724] ath_rate_minstrel: EWMA rolloff level set to 75%
[    2.962367] ath_rate_minstrel: max segment size in the mrr set to 6000 us
insmod: ath_ahb.ko: module not found
load ATH9K 802.11n Driver
[    2.999717] Loading modules backported from Linux version v5.7-rc3-0-g6a8b55ed4056
[    3.007288] Backport generated by backports.git v5.7-rc3-1-0-gc0c7d2bb
load ATH/QCA 802.11ac Driver
cannot open /proc/sys/net/ipv4/ip_conntrack_max
httpd : daemon trying to stop
cannot open /proc/sys/net/ipv4/ip_conntrack_max
klogd : kernel log daemon trying to stop
syslogd : syslog daemon trying to stop
syslogd : daemon successfully started
klogd : daemon successfully started
sorry, your unit does not support resetbutton feature

resetbutton : resetbutton daemon successfully started
bridge : bridge br0 successfully added
CTL_set_cist_bridge_config: Got return code 0, -1
Couldn't find bridge with index 7

Couldn't change bridge bridge_max_age
CTL_set_cist_bridge_config: Got return code 0, -1
Couldn't find bridge with index 7

Couldn't change bridge bridge_forward_delay
CTL_set_msti_bridge_config: Got return code 0, -1
Couldn't find bridge with[    4.922101] device br0 entered promiscuous mode
 index 7

route: ioctl 0x890c failed: No such process
route: ioctl 0x890b failed: Network unreachable
wrt-radauth : Radius daemon trying to stop
hostapd : hostapd daemon trying to stop
wpa_supplicant : wpa_supplicant daemon trying to stop
bridge : bridge br0 successfully added
device br0 already exists; can't create bridge with the same name
CTL_set_cist_bridge_config: Got[    4.960420] device eth1 entered promiscuous mode
 return code 0, -1
Couldn't find bridge with index 7

Couldn't change bridge bridge_max_age
CTL_set_cist_bridge_config: Got return code 0, -1
Couldn't find bridge with index 7

Couldn't change bridge bridge_forward_delay
killall: ead: no process killed
bridge : interface eth1 su[    4.990372] device eth2 entered promiscuous mode
ccessfully added to bridge br0
bridge : interface eth2 successfully added to bridge br0
bridge : interface eth3 s[    5.019790] device eth3 entered promiscuous mode
uccessfully added to bridge br0
sh: ead: not found
[    5.031713] device br0 left promiscuous mode
[    5.039766] device br0 entered promiscuous mode
ifconfig: ioctl [    5.049152] device br0 left promiscuous mode
0x8914 failed: Address not available
wrt-radauth : Radius daemon trying to stop
hostapd : hostapd daemon trying to stop
wpa_supplicant : wpa_supplicant daemon trying to stop
killall: roaming_daemon: no process killed
route_add: if:lo dst:127.0.0.0 gw: 0.0.0.0 mask: 255.0.0.0
route: ioctl 0x890c failed: No such process
route: ioctl 0x890b failed: Network unreachable
mactelnetd : daemon trying to stop
telnetd : daemon trying to stop
transmissiond : daemon trying to stop
snmpd : daemon trying to stop
wland : daemon trying to stop
dropbear : ssh daemon trying to stop
route: ioctl 0x890c failed: No such process
cannot open /proc/sys/net/core/default_qdisc
lld2d : daemon trying to stop
wol : Wake On LAN Daemon trying to stop
proftpd : FTP Server trying to stop
upnp : daemon trying to stop
pppoe-relay : daemon trying to stop
route: ioctl 0x890b failed: Network unreachable
radiusd : daemon trying to stop
klogd : kernel log daemon trying to stop
telnetd : daemon successfully started
tor : daemon trying to stop
minidlna : DLNA Media Server trying to stop
vpnclient : SoftEther Client trying to stop
dnscrypt-proxy : daemon trying to stop
wland : daemon successfully started
klogd : kernel log daemon successfully stopped
vpnserver : SoftEther Server trying to stop
cron : daemon trying to stop
syslogd : syslog daemon trying to stop
cp: can't stat '/tmp/mycron.d/*': No such file or directory
cp: can't stat '/jffs/mycron.d/*': No such file or directory
cp: can't stat '/mmc/mycron.d/*': No such file or directory
syslogd : syslog daemon successfully stopped
syslogd : daemon successfully started
klogd : daemon successfully started
Key is a ssh-rsa key
Wrote key to '/tmp/root/.ssh/ssh_host_rsa_key'
dropbear : ssh daemon trying to stop
vpnbridge : SoftEther Bridge trying to stop
Thu Jan  1 01:00:02 1970 [WARNIN[    5.619648] fast-classifier (PBR safe v2.1.6b): starting up
G] This system d[    5.626706] fast-classifier: registered
oesn't provide enough entropy to quickly generate high-quality random numbers
Thu Jan  1 01:00:02 1970 [WARNING] Installing the rng-utils/rng-tools, jitterentropy or haveged packages may help.
Thu Jan  1 01:00:02 1970 [WARNING] On virtualized Linux environments, also consider using virtio-rng.
Thu Jan  1 01:00:02 1970 [WARNING] The service will no[    5.661513] device eth0 entered promiscuous mode
t start until enough entropy has been collected.
vncrepeater : daemon trying to stop
sfe : shortcut forwarding engine successfully started
dropbear : ssh daemon successfully started
cron : daemon successfully started
rmmod: eoip: No such file or directory
dnsmasq : daemon successfully started
cat: can't open '/proc/sys/net/netfilter/nf_conntrack_flush': No such file or directory
Could not open socket to kernel: Address family not supported by protocol
Could not open socket to kernel: Address family not supported by protocol
igmprt : multicast daemon trying to stop
udpxy : UDP-to-HTTP multicast traffic relay daemon trying to stop
ifconfig: SIOCSI[    6.454903] device eth0 left promiscuous mode
FTXQLEN: No such device
route_del: if:eth0 dst: gw: (null) mask: (null)
eth0: No such process
pppd : daemon trying to stop
pptp : daemon trying to stop
listen : activity daemon trying to stop
pppd : PPP daemon trying to stop
ppp_redial : redial process successfully started
ttraff : traffic counter daemon trying to stop
ttraff : traffic counter daemon successfully started
httpd : daemon trying to stop
httpd : httpd server started at port 80
httpd : http daemon successfully started
resetbutton : daemon trying to stop
sorry, your unit does not support resetbutton feature

resetbutton : resetbutton daemon successfully started
[USB] checking...
/opt/etc/init.d/rcS: No such file or directory
/jffs/etc/init.d/rcS: No such file or directory
/mmc/etc/init.d/rcS: No such file or directory
killall: proxywatchdog.sh: no process killed
httpd : daemon trying to stop
httpd : daemon successfully stopped
httpd : httpd server shutdownhttpd : daemon trying to stop
httpd : httpd server started at port 80
httpd : http daemon successfully started
killall: schedulerb.sh: no process killed
killall: shatd: no process killed
killall: wdswatchdog.sh: no process killed
/jffs/etc/config/openvpn.startup: No such file or directory
/usr/local/etc/config/openvpn.startup: No such file or directory
The Milkfish Router Services
ERROR: Necessary service setting not found: milkfish_username - aborting.
The Milkfish Router Services
Restoring SIP ddsubscriber database from NVRAM...
Empty.
The Milkfish Router Services
Restoring SIP ddaliases database from NVRAM...
Empty.
[    9.072274] libphy: mdio@e0024520:03 - Link is Up - 1000/Full
[    9.078022] br0: port 3(eth3) entered forwarding state
[    9.083164] br0: port 3(eth3) entered forwarding state
[   11.440672] nf_conntrack: automatic helper assignment is deprecated and it will be removed soon. Use the iptables CT target to attach helpers instead.
httpd : Request Error Code 401: Authorization required. please note that the default username is "root" in all newer releases
[   24.101916] br0: port 3(eth3) entered forwarding state
httpd : Request Error Code 401: Authorization required. please note that the default username is "root" in all newer releases
[   37.727314] device eth0 entered promiscuous mode
rmmod: eoip: No such file or directory
cat: can't open '/proc/sys/net/netfilter/nf_conntrack_flush': No such file or directory
Could not open socket to kernel: Address family not supported by protocol
Could not open socket to kernel: Address family not supported by protocol
igmprt : multicast daemon trying to stop
udpxy : UDP-to-HTTP multicast traffic relay daemon trying to stop
ifconfig: SIOCSI[   38.056264] device eth0 left promiscuous mode
FTXQLEN: No such device
route_del: if:eth0 dst: gw: (null) mask: (null)
eth0: No such process
pppd : daemon trying to stop
pppd : daemon successfully stopped
pptp : daemon trying to stop
listen : activity daemon trying to stop
pppd : PPP daemon trying to stop
httpd : Request Error Code 401: Authorization required. please note that the default username is "root" in all newer releases
httpd : Request Error Code 401: Authorization required. please note that the default username is "root" in all newer releases

DD-WRT v3.0-r43397 std (c) 2020 NewMedia-NET GmbH
Release: 06/13/20
Board: Mikrotik RB1000
GIENEK_II
DD-WRT Novice


Joined: 18 Jun 2020
Posts: 21

PostPosted: Sat Jul 11, 2020 18:32    Post subject: Reply with quote
after install test image :
Code:

RouterBOOT booter 6.47

RouterBoard 1000

CPU frequency: 1333 MHz
  Memory size: 512 MiB
    NAND size:  64 MiB

Press any key within 2 seconds to enter setup..
Booting CF
Loading kernel... done
setting up elf image... OK
jumping to kernel code

this is all

can i install some soft from openwrt ?
how i can resize partition (i have 2GB CF card) ??
kernel-panic69
DD-WRT Guru


Joined: 08 May 2018
Posts: 8963
Location: Texas, USA

PostPosted: Sat Jul 11, 2020 18:41    Post subject: Reply with quote
This is the latest public release:

https://download1.dd-wrt.com/dd-wrtv2/downloads/betas/2020/07-09-2020-r43718/mikrotik-rb1000/

What is syslog and dmesg output from the rb1000? That may also be helpful.

_________________
Official Forum Rules, Guidelines & Helpful InformationFirmware FAQInstallation WikiWhere Do I Download Firmware?
DON'T use Chromium-based browsersRTFM/STFW TL;DR is NOT an excuse. • Why Should I Care What Color the Bikeshed Is?
Please DO NOT PM me with questions; Ask in the forum. ---------------------- Linux User #377467 counter.li.org / linuxcounter.net
GIENEK_II
DD-WRT Novice


Joined: 18 Jun 2020
Posts: 21

PostPosted: Sat Jul 11, 2020 18:47    Post subject: Reply with quote
kernel-panic69 wrote:
This is the latest public release:

https://download1.dd-wrt.com/dd-wrtv2/downloads/betas/2020/07-09-2020-r43718/mikrotik-rb1000/

What is syslog and dmesg output from the rb1000? That may also be helpful.


after install this image i have same things like after install test image:
RouterBOOT booter 6.47

RouterBoard 1000

CPU frequency: 1333 MHz
Memory size: 512 MiB
NAND size: 64 MiB

Press any key within 2 seconds to enter setup..
Booting CF
Loading kernel... done
setting up elf image... OK
jumping to kernel code
and this is finish of boot
kernel-panic69
DD-WRT Guru


Joined: 08 May 2018
Posts: 8963
Location: Texas, USA

PostPosted: Sat Jul 11, 2020 19:18    Post subject: Reply with quote
I've already emailed the developer. So, no dmesg or syslog output, only serial? Have you tried accessing web interface, ssh, telnet?
_________________
Official Forum Rules, Guidelines & Helpful InformationFirmware FAQInstallation WikiWhere Do I Download Firmware?
DON'T use Chromium-based browsersRTFM/STFW TL;DR is NOT an excuse. • Why Should I Care What Color the Bikeshed Is?
Please DO NOT PM me with questions; Ask in the forum. ---------------------- Linux User #377467 counter.li.org / linuxcounter.net
GIENEK_II
DD-WRT Novice


Joined: 18 Jun 2020
Posts: 21

PostPosted: Sat Jul 11, 2020 19:23    Post subject: Reply with quote
kernel-panic69 wrote:
I've already emailed the developer. So, no dmesg or syslog output, only serial? Have you tried accessing web interface, ssh, telnet?

i must connect rb1000 to serial port to PC, and then i cannot access the internet, but i do it today or tomorrow (send logs from dmesg and syslog)
in my previous message i send log from dmesg

maybe i will install oldest firmware and then from www make upgrade to last one (webupgrade.bin)

after update from www:
DD-WRT kern.info kernel: [ 1051.884108] openvpnserver[5427]: unhandled signal 4 at 48161fe4 nip 48161fe4 lr 48161fb0 code 30001
same shit ...
BrainSlayer
Site Admin


Joined: 06 Jun 2006
Posts: 7148
Location: Dresden, Germany

PostPosted: Sun Jul 12, 2020 8:57    Post subject: Reply with quote
okay. so doesnt seem even to boot using newer compiler versions for some reason. i will try to find out how to fix it.
_________________
"So you tried to use the computer and it started smoking? Sounds like a Mac to me.." - Louis Rossmann https://www.youtube.com/watch?v=eL_5YDRWqGE&t=60s
GIENEK_II
DD-WRT Novice


Joined: 18 Jun 2020
Posts: 21

PostPosted: Sun Jul 12, 2020 16:38    Post subject: Reply with quote
BrainSlayer wrote:
okay. so doesnt seem even to boot using newer compiler versions for some reason. i will try to find out how to fix it.


can i install some soft from openwrt ?
how i can resize partition (i have 2GB CF card) ??
Goto page Previous  1, 2, 3  Next Display posts from previous:    Page 2 of 3
Post new topic   Reply to topic    DD-WRT Forum Forum Index -> ARM or PPC based Hardware All times are GMT

Navigation

 
Jump to:  
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
You cannot attach files in this forum
You cannot download files in this forum