Firmware: DD-WRT v3.0-r43516 mega (06/25/20) [from: DD-WRT v3.0-r43420 mega (06/15/20) - Good Run!]
Linux Rel: Linux 4.4.228 #1994 Thu Jun 25 mips [from: Linux 4.4.227 #1844 Mon Jun 15 mips]
WireGuard: WireGuard 1.0.20200611 loaded
Reset: NO
Status & Uptime: Working / Tested over 24 hours
Issues/Fixes: none / none
Tests: WireGuard throughput over Dual-WiFi +25Mbps-Down / +15Mbps-Up
Thank-you BrianSlyer for your Great Work and everyone else who makes DD-WRT Great on the Forum! _________________ Home Network on Telus 1Gb PureFibre - 10GbE Copper Backbone
2x R7800 - Gateway & WiFi & 3xWireGuard - DDWRT r53562 Std k4.9
Off Site 1
R7000 - Gateway & WiFi & WireGuard - DDWRT r54517 Std
E3000 - Station Bridge - DDWRT r49626 Mega K4.4
Off Site 2
R7000 - Gateway & WiFi - DDWRT r54517 Std
E2000 - Wired ISP IPTV PVR Blocker - DDWRT r35531
Router/Version: Linksys EA6500 V1
File/Kernel: Linux 4.4.228 #1978 Thu Jun 25 15:46:54 +04 2020 mips
Previous: r43320
Reset: No
Mode: Gateway
Status: OK
Mode/Status: Working
Issues/Errors: None
When flashed via the web ui, it went into a bootloop. I disconnected it and reconnected it and it booted up with no issues, but the router seems to have done a reset itself.
After reconfiguring it, it's been working fine. _________________ Linksys WRT32X, Linksys EA6500 v1, TP-Link TL-WR842ND
Spectrum 940/35 mbit
Posted: Mon Jun 29, 2020 23:59 Post subject: WRT54GSv1 WNDR4500v2 RT-N66R
Router/Version: RT-N66R
Mode: Gateway
File: dd-wrt.v24-43516_NEWD-2_K3.x-big-RT-N66U.trx
Kernel: Linux 4.4.228 #1990 Thu Jun 25 16:03:01 +04 2020 mips
Status: 256Mb RAM is displayed and so far working well Uptime: 4 days, 14 min
Temps: WL0 51.6 °C / WL1 49.6 °C
Router/Version: WNDR4500v2
Mode: AP/Switch/Router
File: dd-wrt.v24-43516_NEWD-2_K3.x_giga-WNDR4500V2.bin
Kernel: Linux 4.4.228 #1978 Thu Jun 25 15:46:54 +04 2020 mips
Status: Working
Uptime: 4 days, 21 min
Temps: WL0 43.7 °C / WL1 44.0 °C
Router/Version: WRT54GSv1
Mode: AP/Switch/Router
File: dd-wrt.v24_mega_generic.bin build 43516
Kernel: Linux 2.4.37 #60862 Thu Jun 25 08:12:06 +04 2020 mips
Status: Working
Uptime: 4 days, 39 min _________________ Asus RT-N66R 50841 big
Netgear WNDR4500v2 50841 mega
IPv6 does only work when IPv4 WAN/PPPoE is deactivated, as soon as I turn on WAN the IPv6 address is dropped. MY ISP only supports IPv6 pass-through which works on stock but I had no luck on ddwrt so far.
OK, almost "my 1st DD-WRT build" (few false starts)
The 1st thing I notice on my Asus RT-N66U is I only see the 5Ghz radio. When I tried dd-wrt.v24-40559_NEWD-2_K3.x-big-RT-N66U.trx, I saw both 5Ghz and 2.4Ghz.
FYI:
Quote:
root@asusrouter:~# lspci -k
00:00.0 FLASH memory: Broadcom Inc. and subsidiaries Sentry5 Chipcommon I/O Controller (rev 01)
00:01.0 Ethernet controller: Broadcom Inc. and subsidiaries BCM47xx Sentry5 USB / Ethernet Controller (rev 01)
Kernel driver in use: et
00:04.0 USB controller: Broadcom Inc. and subsidiaries Device 471a (rev 01)
00:04.1 USB controller: Broadcom Inc. and subsidiaries Device 471a (rev 01)
00:05.0 PCI bridge: Broadcom Inc. and subsidiaries Device 0820 (rev 01)
00:06.0 PCI bridge: Broadcom Inc. and subsidiaries Device 0820 (rev 01)
00:07.0 Unassigned class [ffff]: Broadcom Inc. and subsidiaries Device 052e (rev 01)
00:08.0 RAM memory: Broadcom Inc. and subsidiaries Device 080e (rev 01)
00:09.0 Unassigned class [ffff]: Broadcom Inc. and subsidiaries Device 0534 (rev 01)
01:00.0 Host bridge: Broadcom Inc. and subsidiaries Device 5300 (rev 01)
Subsystem: Broadcom Inc. and subsidiaries Device 5300
01:00.1 Host bridge: Broadcom Inc. and subsidiaries Device 0000 (rev 01)
Subsystem: Broadcom Inc. and subsidiaries Device 5300
01:01.0 Network controller: Broadcom Inc. and subsidiaries BCM4331 802.11a/b/g/n (rev 02)
Subsystem: Broadcom Inc. and subsidiaries BCM4331 802.11a/b/g/n
02:00.0 Host bridge: Broadcom Inc. and subsidiaries Device 5300 (rev 01)
Subsystem: Broadcom Inc. and subsidiaries Device 5300
02:00.1 Host bridge: Broadcom Inc. and subsidiaries Device 0000 (rev 01)
Subsystem: Broadcom Inc. and subsidiaries Device 5300
02:01.0 Network controller: Broadcom Inc. and subsidiaries BCM4331 802.11a/b/g/n (rev 02)
Subsystem: Broadcom Inc. and subsidiaries BCM4331 802.11a/b/g/n
Kernel driver in use: wl
Note only the device with 802.11a/b/g/n is associated with the wl driver
Did you upgrade from 40559 or directly flash 43516? If you upgraded, you most likely need to do an nvram reset, as SO much has changed in the builds.
If you have access to a Telnet/SSH client you can telnet into the router and issue a
Code:
nvram erase && reboot
Then try to reconfigure.
General guidance on wireless is to set a channel and not use "Auto" _________________ ASUS RT-AC3100 AP Merlin 386.12_4
ASUS RT-AC68U Media Bridge/Merlin 386.12_4 (x2)
ASUS RT-AC68U AP r54604
ASUS RT-AC68U Gateway/AP r54604
Edgerouter-4, v2.0.9-hotfix7
I came from DD-WRT v3.0-r41874 big (01/03/20) (tail of woe elsewhere on this site) I did chose the "reset after flash" (on every install, inc this one) it did reset back to e.g. 192.168.1.1 (I know, because it's a bit of a pain on my network)
BTW the 41874, also only showed the 5Ghz radio.
Attached is my dmesg output (assuming attaching works )
Joined: 14 Sep 2019 Posts: 301 Location: Maine, USA
Posted: Thu Jul 02, 2020 10:46 Post subject:
graemev wrote:
I note @turbowells is running
Router/Version: Asus RT-N66U
Firmware: DD-WRT v3.0-r43516 mega (06/25/20)
Are you seeing both 5Ghz and 2.4Ghz interfaces?
(ie , is it just me , or generic to this build on RT-N66U)
Since I've already cleared NVRAM a few times, if it is just me, is there a "debugging guide" somewhere ?
I see both 2.4 Ghz and 5 Ghz via the web interface and on my clients.
Perhaps the interface is showing up on the probe_blacklist. nvram show | grep blacklist .
I had this happen to a wl interface on a different model once due to a bad flash. nvram erase && reboot did not correct it. I had to do a hard reset via the reset button.
Joined: 02 Apr 2007 Posts: 14 Location: Richmond, CA
Posted: Fri Jul 03, 2020 14:38 Post subject: R8000 and WNDR3700v3 seem good with r43516
Router/Version: R8000
File/Kernel: netgear-r8000-webflash.bin
Previous/Reset: r43334 (06-04-2020), no reset
Mode/Status: Gateway, AP
Issues/Errors: not yet
Firmware: DD-WRT v3.0-r43516 std (06/25/20)
8 hrs up so far today, after last night's scheduled reboot
Router/Version: WNDR3700v3
File/Kernel: dd-wrt.v24-43516_NEWD-2_K3.x_mega-nv64k.bin
Previous/Reset: r43334 (06-04-2020), no reset
Mode/Status: CB (5 GHz), AP (2.4 GHz)
Issues/Errors: not yet
Firmware: DD-WRT v3.0-r43516 mega (06/25/20)
7.5 hrs up so far today, after last night's scheduled reboot
Seems pretty good so far, no complaints yet. Thanks for making this available.
Posted: Sat Jul 04, 2020 12:35 Post subject: RT-AC5300 Exp No 5GHz
Router/Version: ASUS RT-AC5300
File/Kernel: asus_rt-ac5300-firmware.trx
Previous/Reset: r43516 std (06-25-2020), reset
Mode/Status: AP
Issues/Errors: 5GHz Radios do not work
Firmware: DD-WRT v3.0-r43516 std (06/25/20)
I had this working with the standard build, but I was trying to solve some issues with VAPs that appear to be related to channel interference with my other routers.
The GUI says the radios are working, but a wireless scan shows that they are not, and no clients are connecting.
