Posted: Wed Jun 17, 2020 21:31 Post subject: New Build - 06/17/2020 - r43443
[WARNING]: This thread is only for feedback on this beta release for developers and the community's benefit.
DO NOT flash this beta release unless you understand the risks involved and specific device recovery methods.
Avoid discussions! Create threads for questions, general problems or use search; this thread is not for support.
Please list router model & revision, operating & wireless mode(s) and exact filename/firmware image flashed.
Notes:
• CVE-2019-14899 VPN fix from December, since then various revisions including recently 7040.
• In-kernel Samba has been implemented this year and default min/max versions have changed, with WSD support.
• VAP issue is fixed! For any Wireless Mode, create a VAP and both ath0/ath1 should now function properly.
• Local DNS option removed from Services->DNSMasq in changesets 43080 and 43081; ref: #7092
• DHCP and DNS help (English) updated in 43083; ref: #7091
• WireGuard: Policy Based Routing, Kill Switch, Inbound Firewall, Naming of Peers, Status, Key, Guides. Thanks egc!
Issues:
• There may be remaining issues for Samba (for example NTFS), with frequent updates.
Important:
• If reporting issues provide applicable info: 'dmesg', 'cat /tmp/var/log/messages', syslog/serial output, strace etc.
• For firewall issues provide 'iptables -L', 'iptables -t nat -L' and the /tmp/.ipt file.
• Search existing SVN tickets before opening a new one. Before reporting, reset and manually setup (no nvram backup).
• Be sure to include operating and wireless modes (Gateway, AP, CB, etc.) along with relevant configuration information.
Joined: 16 Nov 2015 Posts: 6435 Location: UK, London, just across the river..
Posted: Wed Jun 17, 2020 22:05 Post subject:
Router Model TP-Link WR1043ND V2
Firmware Version DD-WRT v3.0-r43443 std (06/17/20)
Kernel Version Linux 3.18.140-d4 #81623 Wed Jun 17 10:16:57 +04 2020 mips
update: CLI 43420 > 43443
reset: NO
status: Operational 20h+
errors: tested ed25519... it seems not ready yet...WIP _________________ Atheros
TP-Link WR740Nv1 ---DD-WRT 55630 WAP
TP-Link WR1043NDv2 -DD-WRT 55723 Gateway/DoT,Forced DNS,Ad-Block,Firewall,x4VLAN,VPN
TP-Link WR1043NDv2 -Gargoyle OS 1.15.x AP,DNS,QoS,Quotas
Qualcomm-Atheros
Netgear XR500 --DD-WRT 55779 Gateway/DoH,Forced DNS,AP Isolation,4VLAN,Ad-Block,Firewall,Vanilla
Netgear R7800 --DD-WRT 55779 Gateway/DoT,AD-Block,Forced DNS,AP&Net Isolation,x3VLAN,Firewall,Vanilla
Netgear R9000 --DD-WRT 55779 Gateway/DoT,AD-Block,AP Isolation,Firewall,Forced DNS,x2VLAN,Vanilla
Broadcom
Netgear R7000 --DD-WRT 55460 Gateway/SmartDNS/DoH,AD-Block,Firewall,Forced DNS,x3VLAN,VPN
NOT USING 5Ghz ANYWHERE
------------------------------------------------------
Stubby DNS over TLS I DNSCrypt v2 by mac913
Last edited by Alozaros on Thu Jun 18, 2020 15:41; edited 1 time in total
ummm... SAMBA NO worky on EA8500 with either of these r43443
Linksys EA8500
DD-WRT v3.0-r43443 std (06/17/20)
Linux 4.9.227 #587 SMP Wed Jun 17 13:17:58 +03 2020 armv7l ...public release
Linksys EA8500
DD-WRT v3.0-r43443 std (06/17/20)
Linux 4.9.227 #585 SMP Wed Jun 17 04:24:33 +03 2020 armv7l
* * *
this is on the EA8500 used as (WAN port assisgned to) switch, ovpn server, VLAN
but acts same as main router EA8500 I put the 1st. r43443 on in the wee hours this morning
yea, SAMBA works just fine on both with r43420 and several previous builds.
logs don't say much but here is my config:
Code:
root@EA8500:~# cat /tmp/smb.conf
[global]
log level = 1
netbios name = EA8500
server string =
syslog = 10
encrypt passwords = true
preferred master = yes
use sendfile = yes
aio read size = 2048
aio write size = 2048
large readwrite = yes
security = user
oplocks = yes
mangled names = no
max stat cache size = 64
workgroup =
bind interfaces only = yes
guest account = nobody
map to guest = Bad User
smb passwd file = /var/samba/smbpasswd
private dir = /var/samba
passdb backend = smbpasswd
log file = /var/smbd.log
max log size = 1000
socket options = TCP_NODELAY IPTOS_LOWDELAY SO_SNDBUF=262144 SO_RCVBUF=262144
read raw = yes
write raw = yes
max xmit = 65536
dead time = 15
getwd cache = yes
lpq cache time = 30
min protocol = SMB3_11
max protocol = SMB3_11
printing = none
load printers = No
usershare allow guests = Yes
smb3 encryption = yes
[TEST]
comment = TEST
path = /mnt/sda/
read only = no
guest ok = no
valid users = mrjcd
force user = root
root@EA8500:~#
*********************************************
AND
SAMBA won't work on this bugger either ...but all else looks ok
Netgear WNDR3700 V4
DD-WRT v3.0-r43443 std (06/17/20)
Linux 3.18.140-d4 #81651 Wed Jun 17 11:12:11 +04 2020 mips
installed r43420 back on it and all works perfect.
ummm... SAMBA NO worky on EA8500 with either of these r43443
Linksys EA8500
DD-WRT v3.0-r43443 std (06/17/20)
Linux 4.9.227 #587 SMP Wed Jun 17 13:17:58 +03 2020 armv7l ...public release
Linksys EA8500
DD-WRT v3.0-r43443 std (06/17/20)
Linux 4.9.227 #585 SMP Wed Jun 17 04:24:33 +03 2020 armv7l
* * *
this is on the EA8500 used as (WAN port assisgned to) switch, ovpn server, VLAN
but acts same as main router EA8500 I put the 1st. r43443 on in the wee hours this morning
yea, SAMBA works just fine on both with r43420 and several previous builds.
logs don't say much but here is my config:
Code:
root@EA8500:~# cat /tmp/smb.conf
[global]
log level = 1
netbios name = EA8500
server string =
syslog = 10
encrypt passwords = true
preferred master = yes
use sendfile = yes
aio read size = 2048
aio write size = 2048
large readwrite = yes
security = user
oplocks = yes
mangled names = no
max stat cache size = 64
workgroup =
bind interfaces only = yes
guest account = nobody
map to guest = Bad User
smb passwd file = /var/samba/smbpasswd
private dir = /var/samba
passdb backend = smbpasswd
log file = /var/smbd.log
max log size = 1000
socket options = TCP_NODELAY IPTOS_LOWDELAY SO_SNDBUF=262144 SO_RCVBUF=262144
read raw = yes
write raw = yes
max xmit = 65536
dead time = 15
getwd cache = yes
lpq cache time = 30
min protocol = SMB3_11
max protocol = SMB3_11
printing = none
load printers = No
usershare allow guests = Yes
smb3 encryption = yes
[TEST]
comment = TEST
path = /mnt/sda/
read only = no
guest ok = no
valid users = mrjcd
force user = root
root@EA8500:~#
*********************************************
AND
SAMBA won't work on this bugger either ...but all else looks ok
Netgear WNDR3700 V4
DD-WRT v3.0-r43443 std (06/17/20)
Linux 3.18.140-d4 #81651 Wed Jun 17 11:12:11 +04 2020 mips
installed r43420 back on it and all works perfect.
I just wanted to let you know that I just updated this morning and I don't seem to have any issues with Samba.
This is my output for the config file.
root@Router2:~# cat /tmp/smb.conf
[global]
log level = 1
netbios name = Router2
server string = DD-WRT-Nas
syslog = 10
encrypt passwords = true
preferred master = yes
use sendfile = yes
aio read size = 2048
aio write size = 2048
large readwrite = yes
security = user
oplocks = yes
mangled names = no
max stat cache size = 64
workgroup = WORKGROUP
bind interfaces only = yes
guest account = nobody
map to guest = Bad User
smb passwd file = /var/samba/smbpasswd
private dir = /var/samba
passdb backend = smbpasswd
log file = /var/smbd.log
max log size = 1000
socket options = TCP_NODELAY IPTOS_LOWDELAY SO_SNDBUF=262144 SO_RCVBUF=262144
read raw = yes
write raw = yes
max xmit = 65536
dead time = 15
getwd cache = yes
lpq cache time = 30
min protocol = SMB3_11
max protocol = SMB3_11
printing = none
load printers = No
usershare allow guests = Yes
smb3 encryption = no
[Data]
comment = Data
path = /mnt/sda4//
read only = no
guest ok = no
valid users = xraive
force user = root
root@Router2:~#
Syslog output: Looks good except the start-up errors you mentioned were OK from the build r43397.
root@Router2:~# cat /var/log/messages | grep "err"
Dec 31 19:00:13 Router2 kern.err kernel: [ 0.104641] msm_bus_fabric_init_driver
Dec 31 19:00:13 Router2 kern.err kernel: [ 1.357776] qcom-pcie 1b900000.pci: phy link never came up
Dec 31 19:00:13 Router2 kern.err kernel: [ 1.359626] qcom-pcie 1b900000.pci: hostinit failed
Dec 31 19:00:13 Router2 kern.err kernel: [ 3.371103] Calibration not found.
Dec 31 19:00:13 Router2 kern.err kernel: [ 3.374946] CPUidle arm: CPU 0 failed to init idle CPU ops
Dec 31 19:00:13 Router2 kern.err kernel: [ 3.554618] no valid UBI magic found inside mtd13
Dec 31 19:00:13 Router2 kern.warn kernel: [ 7.819054] ath10k_pci 0000:01:00.0: Direct firmware load for ath10k/QCA99X0/hw2.0/firmware-6.bin failed with error -2
Dec 31 19:00:13 Router2 kern.warn kernel: [ 9.759142] ath10k_pci 0001:01:00.0: Direct firmware load for ath10k/QCA99X0/hw2.0/firmware-6.bin failed with error -2
Dec 31 19:00:14 Router2 daemon.info mstpd[739]: error, CTL_set_cist_bridge_config: Couldn't find bridge with index 9
Dec 31 19:00:14 Router2 daemon.info mstpd[739]: error, CTL_set_cist_bridge_config: Couldn't find bridge with index 9
Dec 31 19:00:17 Router2 user.err wsdd2[1141]: error: wsdd-mcast-v4: wsd_send_soap_msg: send
Dec 31 19:00:24 Router2 kern.info kernel: [ 24.365018] sdhci: Copyright(c) Pierre Ossman
Dec 31 19:00:25 Router2 kern.err kernel: [ 25.077459] sd 1:0:0:0: [sda] No Caching mode page found
Dec 31 19:00:25 Router2 kern.err kernel: [ 25.079182] sd 1:0:0:0: [sda] Assuming drive cache: write through
Dec 31 19:00:25 Router2 user.err wsdd2[1141]: Terminated received.
Dec 31 19:00:27 Router2 local5.err ksmbd: [ksmbd-manager/1804]: ERROR: Failed to create lock file: File exists
Dec 31 19:00:28 Router2 local5.err ksmbd: [ksmbd-manager/1998]: ERROR: Failed to create lock file: File exists
Dec 31 19:00:28 Router2 local5.err ksmbd: [ksmbd-manager/1996]: ERROR: Failed to create lock file: File exists
Dec 31 19:00:28 Router2 daemon.err ntpclient[1411]: Failed resolving address to hostname 1.ca.pool.ntp.org: Try again
Dec 31 19:00:28 Router2 daemon.err ntpclient[1411]: Failed resolving server 1.ca.pool.ntp.org: Network is down
Dec 31 19:00:28 Router2 daemon.err process_monitor[1410]: cyclic NTP Update failed (servers 1.ca.pool.ntp.org)
Dec 31 19:00:28 Router2 daemon.err process_monitor[1410]: Last update failed, we need to re-update after 30 seconds
Dec 31 19:00:28 Router2 local5.err ksmbd: [ksmbd-manager/2027]: ERROR: Failed to create lock file: File exists
Dec 31 19:00:29 Router2 local5.err ksmbd: [ksmbd-manager/2089]: ERROR: Failed to create lock file: File exists
Jun 18 07:27:30 Router2 user.err wsdd2[2086]: Terminated received.
Jun 18 07:27:30 Router2 user.err wsdd2[2019]: Terminated received.
Jun 18 07:27:30 Router2 user.err wsdd2[1986]: Terminated received.
Jun 18 07:27:30 Router2 user.err wsdd2[1985]: Terminated received.
Jun 18 07:27:30 Router2 user.err wsdd2[1798]: Terminated received.
Jun 18 07:27:30 Router2 user.err wsdd2[1665]: Terminated received.
root@Router2:~#
Edit
I would like to add that when I did try to add some files to my share the first time my computer did freeze. Once I killed "explorer.exe". I was able to browse and move files to my share without issue.
I checked syslog and I saw this entry.
Jun 18 07:41:57 Router2 kern.err kernel: [ 1725.855228] ksmbd: set_file_allocation_info:5406: ksmbd_vfs_alloc_size is failed : -95
Jun 18 07:41:57 Router2 kern.err kernel: [ 1725.855834] ksmbd: set_file_allocation_info:5406: ksmbd_vfs_alloc_size is failed : -95
Maybe there is something because I didn't see this error before. Will continue testing.
Edit
From the quick testing that I did, I'm able to move files (text files) to my share and edit/save them without issue. However when I try to create new files (text files) add content and save them to my share I get the following errors.
I get the following erros:
Jun 18 07:41:57 Router2 kern.err kernel: [ 1725.855228] ksmbd: set_file_allocation_info:5406: ksmbd_vfs_alloc_size is failed : -95
Jun 18 07:41:57 Router2 kern.err kernel: [ 1725.855834] ksmbd: set_file_allocation_info:5406: ksmbd_vfs_alloc_size is failed : -95
Jun 18 07:47:15 Router2 kern.err kernel: [ 2043.882425] ksmbd: set_file_allocation_info:5406: ksmbd_vfs_alloc_size is failed : -95
Jun 18 07:47:15 Router2 kern.err kernel: [ 2043.883020] ksmbd: set_file_allocation_info:5406: ksmbd_vfs_alloc_size is failed : -95
Jun 18 07:47:35 Router2 kern.err kernel: [ 2063.312178] ksmbd: set_file_allocation_info:5406: ksmbd_vfs_alloc_size is failed : -95
Jun 18 07:47:42 Router2 kern.err kernel: [ 2070.999165] ksmbd: set_file_allocation_info:5406: ksmbd_vfs_alloc_size is failed : -95
Jun 18 07:48:43 Router2 kern.err kernel: [ 2131.374521] ksmbd: set_file_allocation_info:5406: ksmbd_vfs_alloc_size is failed : -95
Jun 18 07:48:57 Router2 kern.err kernel: [ 2145.245280] ksmbd: set_file_allocation_info:5406: ksmbd_vfs_alloc_size is failed : -95
Jun 18 07:49:10 Router2 kern.err kernel: [ 2158.907881] ksmbd: set_file_allocation_info:5406: ksmbd_vfs_alloc_size is failed : -95
Jun 18 07:49:29 Router2 kern.err kernel: [ 2177.898943] ksmbd: set_file_allocation_info:5406: ksmbd_vfs_alloc_size is failed : -95
Jun 18 07:49:29 Router2 kern.err kernel: [ 2177.899438] ksmbd: set_file_allocation_info:5406: ksmbd_vfs_alloc_size is failed : -95
Jun 18 07:51:17 Router2 kern.err kernel: [ 2286.062594] ksmbd: set_file_allocation_info:5406: ksmbd_vfs_alloc_size is failed : -95
Jun 18 07:52:54 Router2 kern.err kernel: [ 2382.180774] ksmbd: set_file_allocation_info:5406: ksmbd_vfs_alloc_size is failed : -95
Jun 18 07:53:57 Router2 kern.err kernel: [ 2445.319726] ksmbd: set_file_allocation_info:5406: ksmbd_vfs_alloc_size is failed : -95
Posted: Thu Jun 18, 2020 15:23 Post subject: Upgrades
Router/Version: Netgear R7800
Firmware: 43443
Previous: 43420
Mode/Status: WDS AP, QoS, DHCP
Reset: No
Issues/Errors: None, so far.
Router/Version: TP-Link Archer C7 v2 x2
Firmware: 43443
Previous: 43420
Mode/Status: WDS Station
Reset: No
Issues/Errors: None, so far.
Router/Version: D-Link DIR-862L A1 x2
Firmware: 43443
Previous: 43420
Mode/Status: WDS Station
Reset: No
Issues/Errors: None, so far.
Router/Version: D-Link DIR-825 B1
Firmware: 43443
Previous: 43420
Mode/Status: WDS Station
Reset: No
Issues/Errors: None, so far.
Router/Version: TP-Link WR841ND v8
Firmware: 43443
Previous: 43420
Mode/Status: WDS Station
Reset: No
Issues/Errors: None, so far.
Router/Version: TP-Link WDR3600 v1
Firmware: 43443
Previous: 43420
Mode/Status: WDS Station
Reset: No
Issues/Errors: None, so far.
Router/Version: D-Link WNDR3700 v2
Firmware: 43443
Previous: 43420
Mode/Status: WDS Station
Reset: No
Issues/Errors: None, so far.
& Broadcom based:
Router/Version: Asus RT-N66u
Firmware: 43443
Previous: 43420
Mode/Status: AP
Reset: No
Issues/Errors: None, so far. _________________ Before asking a question on the forums, update dd-wrt: Where do I download firmware? I suggest reading it all.
QCA Best WiFi Settings
Some dd-wrt wiki pages are up to date, others are not. PM me if you find an old one.
Atheros:
Netgear R7800 x3 - WDS AP / station, gateway, QoS
TP-Link Archer C7 v2 x2 - WDS Station
TP-Link TL-WDR3600 v1 - WDS Station
TP-Link 841nd v8 - NU
D-Link 615 C1/E3/I1 x 7 - 1 WDS station
D-Link 825 B1 - NU
D-Link 862L A1 x2 - WDS Station
Netgear WNDR3700v2 - NU
UBNT loco M2 x2 - airOS
Broadcom
Linksys EA6400 - Gateway, QoS
Asus N66U - AP
Netgear WNDR3700v3 - not used
MediaTek
UBNT EdgeRouter X - switch
Router/Version: Fonera 2201
File: linux.bin - gargoyle fon flash utility
Firmware: DD-WRT v3.0-r43443 std (06/17/20)
Kernel: Linux 3.2.102 #127954 Wed Jun 17 15:58:21 +04 2020 mips
Mode: AP
Previous: so many Reset?: N, some nvram CLI ajust.
Status: Alive.
Router/Version: Netgear R9000
Firmware: 43443
Previous: 43420
Mode/Status: WDS AP
Reset: No
Issues/Errors: TLS errors on boot when attempting to connect to VPN, increased ping, have reverted back to 43420.
Router/Version: Netgear R7800
Firmware: 43443
Previous: 43420
Mode/Status: WDS Station
Reset: No
Issues/Errors: None that I could see, but have reverted back to 43420 to match AP.
