Posted: Wed May 27, 2020 14:17 Post subject: New Build - 05/27/2020 - r43266
[WARNING]: This thread is only for feedback on this beta release for developers and the community's benefit.
DO NOT flash this beta release unless you understand the risks involved and specific device recovery methods.
Avoid discussions! Create threads for questions, general problems or use search; this thread is not for support.
Please list router model & revision, operating & wireless mode(s) and exact filename/firmware image flashed.
Issues, observations, and/or workarounds reported:
• DNScrypt 1.95 can still be used in the GUI but v2 (not compatible) requires Golang and thus Entware. 6246
• WDS does not work on Broadcom ARM devices(only MIPS<->MIPS) and bridge modes on k4.4 devices may sometimes work in some configurations in certain builds but are not supported by the bcmdhd driver. Use client or repeater instead.
• VAPs not working at bootfixed for unbridged VAPs with r40564:40566.Workaround startup command:
sleep 10;stopservice nas;stopservice wlconf;startservice wlconf;startservice nas(there are a few alternatives, search).
• If start-up scripts do not work from USB add a delay (e.g. wait script or 'sleep 25').
Important:
• If reporting issues provide applicable info: 'dmesg', 'cat /tmp/var/log/messages', syslog/serial output, strace etc.
• For firewall issues provide 'iptables -L', 'iptables -t nat -L' and the /tmp/.ipt file.
• Search existing SVN tickets before opening a new one. Before reporting, reset and manually setup (no nvram backup).
• Be sure to include operating and wireless modes (Gateway, AP, CB, etc.) along with relevant configuration information.
Router: R7000
Firmware: 05/27/20 -r43266
Previous: 05/26/20 -r43261
Mode: AP/Gateway
Reset: No
Uptime: about 15 minutes
Problems/Errors: none observed as of yet
Flashed this morning after checking Trac, and this thread. No issues to report, but will of course update this pose if any come up. One question about modes, I know my wireless is set to AP, I have been saying gateway because it's the only router on the network. Is this correct, or should I be listing the mode as router? If I've seen the mode in settings and have overlooked it,I apologize.
Router/Version: RT-AC87U A1
File: asus_rt-ac87u-firmware.trx
Firmware: DD-WRT v3.0-r43266 std (05/27/20)
Kernel: Linux 4.4.224 #246 SMP Wed May 27 09:43:59 +04 2020 armv7l
Previous: DD-WRT v3.0-r43217 std (05/22/20)
Mode/Status: Gateway/AP/Ok
Reset: No
Setup Using: 2.4 GHz, 2.4 GHz guest (VAP), 5.0 GHz, IPv4, DNSMasq, Port Forwarding, USB, NAS, NTP TimeSync, and Wake-on-WAN(internet)
Issues/Errors: YES, when signing into the USB drive mounted on the router’s 3.0 port through Windows File Explorer the router reboots.
Rolling back to r43217 _________________ Netgear XR500, R7800
Asus AC87Ua1
Repeater Bridge
Netgear R6400v2otp
Last edited by jrscs on Wed May 27, 2020 20:03; edited 1 time in total
Router/Version: Netgear R7000
Firmware: DD-WRT v3.0-r43266 std (05/27/20)
Kernel: Linux 4.4.224 #246 SMP Wed May 27 09:43:59 +04 2020 armv7l
Previous: r43261
Mode/Status: Gateway / working
Reset: no
Issues/Errors: Working well so far.
Uptime: 4hrs 25min
Temperatures: CPU 66.9 °C / WL0 47.0 °C / WL1 52.8 °C
Router: ASUS RT-AC68U rev A1 & C1
Firmware: asus_rt-ac68u-firmware.trx
Previous: 05/26/20 -r43261
Mode: Gateway / AP
Reset: No, flashed from CLI
Problems/Errors: No, works well _________________ Netgear R7000 on Build 55109
Asus AC-AC68U rev. C1 (AP) on Build 55109
Asus AC-68U rev. A1 on Build 54604
Asus AC-68U rev. A1 on Build 53339
Router Model: Netgear R8000
Firmware Version: DD-WRT v3.0-r43266 std (05/27/20)
Kernel Version: Linux 4.4.224 #246 SMP Wed May 27 09:43:59 +04 2020 armv7l
Mode: AP
Reset: no
Previous: r43261
Upgrade: via webgui
Drivers: experimental
Status: 2.4 ghz, openvpn client, dhcp server enabled, all working
Issue: none, internet download speed has greatly improved
Errors: according to the syslog below
Dec 31 20:00:10 DD-WRT kern.err kernel: bcmsflash: found no supported devices
Dec 31 20:00:13 DD-WRT kern.err kernel: brcmfmac: brcmf_cfg80211_dump_survey: cca_get_stats failed (-52)
Dec 31 20:00:16 DD-WRT kern.err kernel: brcmfmac: brcmf_cfg80211_dump_survey: cca_get_stats failed (-52)
May 27 18:32:55 DD-WRT kern.err kernel: brcmfmac: brcmf_cfg80211_dump_survey: cca_get_stats failed (-52)
May 27 18:32:55 DD-WRT kern.err kernel: brcmfmac: brcmf_cfg80211_dump_survey: cca_get_stats failed (-52)
May 27 18:32:55 DD-WRT kern.err kernel: brcmfmac: brcmf_cfg80211_dump_survey: cca_get_stats failed (-52)
May 27 18:32:58 DD-WRT kern.err kernel: brcmfmac: brcmf_cfg80211_dump_survey: cca_get_stats failed (-52)
May 27 18:32:58 DD-WRT kern.err kernel: brcmfmac: brcmf_cfg80211_dump_survey: cca_get_stats failed (-52)
May 27 18:32:58 DD-WRT kern.err kernel: brcmfmac: brcmf_cfg80211_dump_survey: cca_get_stats failed (-52)
May 27 18:33:01 DD-WRT kern.err kernel: brcmfmac: brcmf_cfg80211_dump_survey: cca_get_stats failed (-52)
May 27 18:33:01 DD-WRT kern.err kernel: brcmfmac: brcmf_cfg80211_dump_survey: cca_get_stats failed (-52)
May 27 18:33:01 DD-WRT kern.err kernel: brcmfmac: brcmf_cfg80211_dump_survey: cca_get_stats failed (-52)
May 27 18:33:04 DD-WRT kern.err kernel: brcmfmac: brcmf_cfg80211_dump_survey: cca_get_stats failed (-52)
May 27 18:33:04 DD-WRT kern.err kernel: brcmfmac: brcmf_cfg80211_dump_survey: cca_get_stats failed (-52)
The CFE recovery showed up and asked for a firmware file, I tried selecting this one again but it rebooted to the CFE recovery, and I tried selecting the previous build I had but that one hadn't rebooted the router before I had to leave work. I'll know more when I get back in to my office. _________________ Asus RT-N66R 50841 big
Netgear WNDR4500v2 50841 mega
The CFE recovery showed up and asked for a firmware file, I tried selecting this one again but it rebooted to the CFE recovery, and I tried selecting the previous build I had but that one hadn't rebooted the router before I had to leave work. I'll know more when I get back in to my office.
Posted: Thu May 28, 2020 3:37 Post subject: WRT54GSv1 WNDR4500v2 RT-N66R
Router/Version: RT-N66R
Mode: AP/Switch/Router
File: dd-wrt.v24-43266_NEWD-2_K3.x-big-RT-N66U.trx
Kernel: Linux 4.4.224 #1408 Wed May 27 14:49:07 +04 2020 mips
Status: Working
Uptime: 2 min
Temps: WL0 52.3 °C / WL1 50.6 °C
Router/Version: WNDR4500v2
Mode: AP/Switch/Router
File: dd-wrt.v24-43266_NEWD-2_K3.x_giga-WNDR4500V2.bin
Kernel: Linux 4.4.224 #1396 Wed May 27 14:35:15 +04 2020 mips
Status: Working
Uptime: 11 min
Temps: WL0 43.2 °C / WL1 43.6 °C
Router/Version: WRT54GSv1
Mode: AP/Switch/Router
File: dd-wrt.v24_mega_generic.bin from 43266 build folder
Kernel: Linux 2.4.37 #60455 Wed May 20 06:56:31 +04 2020 mips
Status: Working
Uptime: 9 min
Flashing the WRT54GSv1 from the dd-wrt.v24_mega_generic.bin file from the 43266 build Brodcom folder still results in the build and kernel displaying 43195 and 2.4.37 60455. _________________ Asus RT-N66R 50841 big
Netgear WNDR4500v2 50841 mega
Joined: 16 Mar 2019 Posts: 353 Location: Szczecin, Poland EU
Posted: Thu May 28, 2020 11:24 Post subject:
Router/Version: Netgear WNR3500L v2
File: dd-wrt.v24-43266_NEWD-2_K3.x_giga-WNR3500Lv2
Previous/Reset: build 43261 without reset
Kernel: Linux 4.4.224 #1396 Wed May 27 14:35:15 +04 2020 mips
Mode/Status: Internet gateway and wifi AP
Issues/Errors: working rather without problems
Uptime: almost 20h
Router working. I'm updated it via ssh without problems. I think everything is rather without erros and issues. I have the new kernel line. I don't see big differents from an old builds to actual.
Router Model: Netgear R6250
Firmware Version: DD-WRT v3.0-r43266 std (05/27/20)
Kernel Version: Linux 4.4.224 #246 SMP Wed May 27 09:43:59 +04 2020 armv7l
Mode: AP
Previous: DD-WRT v3.0-r43217 std (05/22/20)
Reset: no
Upgraded: via webgui
Status: samba, nas, usb, 2.4 Ghz working
Issues: none
Errors: according to syslog below
Dec 31 20:00:10 DD-WRT kern.err kernel: bcmsflash: found no supported devices
Dec 31 20:00:26 DD-WRT daemon.err ntpclient[1063]: Failed resolving address to hostname 2.pool.ntp.org: Try again
Dec 31 20:00:26 DD-WRT daemon.err ntpclient[1063]: Failed resolving server 2.pool.ntp.org: Network is down
May 28 09:41:31 DD-WRT kern.err kernel: hub 3-0:1.0: config failed, hub doesn't have any ports! (err -19)