Joined: 08 May 2018 Posts: 14223 Location: Texas, USA
Posted: Fri Nov 29, 2019 4:24 Post subject:
tatsuya46 wrote:
could syslog be broken? cause theres zero hostapd output even though i enable it in hostapd conf..
The thing is, all of the stuff that normally would output to syslog, or a large percentage of the debugging stuff is NOT enabled by default in BS builds. Personally, I would love to see that only NTP sync failures only get logged and fuck everything else except it starting, dying, restarting. Nothing else. Kong was a little more attentive to these things... _________________ "Life is but a fleeting moment, a vapor that vanishes quickly; All is vanity"
Contribute To DD-WRT Pogo - A minimal level of ability is expected and needed... DD-WRT Releases 2023 (PolitePol)
DD-WRT Releases 2023 (RSS Everything)
----------------------
Linux User #377467 counter.li.org / linuxcounter.net
Joined: 16 Nov 2015 Posts: 6440 Location: UK, London, just across the river..
Posted: Wed Dec 04, 2019 10:18 Post subject:
hahaha well... now im one of those buggers.....!!!
if someone clears out this thread R7800, from all the vomit...,there will be a lots of valuable information in it
1, 2, 3 ... 186, 187, 188 its a kind of a scary number to learn about to go trough about this unit and all issues around the Sun too..
apart of that, not many of us left this day's....
and yea its not bad idea for a router base update, wiki, supported devices and ect., keep up with the good job...
Im about to break the long-lasting R7800 40270 last Kong build...still in use..... and give a try to BS builds just in regard to an updated Wiregurd....and others.... _________________ Atheros
TP-Link WR740Nv1 ---DD-WRT 55630 WAP
TP-Link WR1043NDv2 -DD-WRT 55723 Gateway/DoT,Forced DNS,Ad-Block,Firewall,x4VLAN,VPN
TP-Link WR1043NDv2 -Gargoyle OS 1.15.x AP,DNS,QoS,Quotas
Qualcomm-Atheros
Netgear XR500 --DD-WRT 55779 Gateway/DoH,Forced DNS,AP Isolation,4VLAN,Ad-Block,Firewall,Vanilla
Netgear R7800 --DD-WRT 55819 Gateway/DoT,AD-Block,Forced DNS,AP&Net Isolation,x3VLAN,Firewall,Vanilla
Netgear R9000 --DD-WRT 55779 Gateway/DoT,AD-Block,AP Isolation,Firewall,Forced DNS,x2VLAN,Vanilla
Broadcom
Netgear R7000 --DD-WRT 55460 Gateway/SmartDNS/DoH,AD-Block,Firewall,Forced DNS,x3VLAN,VPN
NOT USING 5Ghz ANYWHERE
------------------------------------------------------
Stubby DNS over TLS I DNSCrypt v2 by mac913
Im about to break the long-lasting R7800 40270 last Kong build...still in use..... and give a try to BS builds just in regard to an updated Wiregurd....and others....
Me too I’m in the same troub...ehm, situation. But last time I switched from Kong 402070 to BS build, the WAN stopped to acquire the IP, don’t ask why, I made a full reset and nothing changed, maybe somethings is different in the way the BS’s builds acquire the wan ip? Also the jffs2 space stopped working but the reset fixed it. Anyway I’m too lazy to insert all the fields/settings again so I switched back to 402070.
I think the limit is the security of the old builds, until they’re not secure it can be used, I’m still with a 2017 build on an old Buffalo router.
Me too I’m in the same troub...ehm, situation. But last time I switched from Kong 402070 to BS build, the WAN stopped to acquire the IP, don’t ask why, I made a full reset and nothing changed, maybe somethings is different in the way the BS’s builds acquire the wan ip?
Even on r6300 a switch from Kong to BS caused difficulties with the WAN. I haven't put my r7800 as the gateway yet but from your experience I'll probably have the same problem.
The workaround for me is Setup->Advanced Routing->Operating Mode: switch to Router, Apply Settings, then back to Gateway, Apply Settings, then the WAN works until the next modem or router restart.
@msoengineer: Thanks for the warning at the top of the supported routers page. That would have saved me from the router database trap when I first tried dd-wrt.
Hi guys, Im kinda new to this and have a few problems getting ddwrt going with the latest bs build 12/21. Everything is great but ipv6 and dslreports speedtest. When I try and run speedtest it throws up tons of errors regardless of browser or http https. When I try http it says no ipv6 connectivity and after running ipv6 tests it seems I dont have it working. I have enabled it on the router and I have comcast in florida and an ax200 intel wifi 6 card in my pc. Anyone care to help me get going.
Posted: Thu Dec 26, 2019 21:00 Post subject: Bridge configuration partially loaded on reboot ?
Using old kong builds up to the last r40270 I seem to have a problem where on a reboot of the router some interfaces are missing from the bridges I configured. As a example, eth1.3 is missing from br1 ..
When I however use 'apply settings' the complete bridge config loads properly.
Note that I'm using a startup script to create my vlans.
Does someone know why this is happening ?
Last edited by kasperskie on Thu Dec 26, 2019 21:04; edited 2 times in total
