[thommy181]

Router/Version: Netgear WNR3500L v2
Mode: Internet gateway and WIFI AP
File: dd-wrt.v24-42617_NEWD-2_K3.x_mega-WNR3500Lv2
Kernel: Linux 3.10.108-d10 #2768 Thu Mar 5 12:50:10 +04 2020 mips
Status: Working
Uptime: ~ 26 hours
Reset: No

I'm update device via ssh. Generally router working correctly. I can't to change configuration in Setup -> Switch config tab. When I'm put there custom configuration and apply changes device back to default ports config. This problem is still.

[jikkine]

Hi, i made factory defaults. Samba doesn't work. I cannot access to shared folders via Windows 10 even Android. Is there any way to get it working?

Thank you

[kernel-panic69]

You should report router make, model, etc. etc. etc. and then put your errors; then, open a new thread about how to fix your problem.

[jikkine]

Router Model: Asus RT-N18U
Firmware Version: DD-WRT v3.0-r42617 std (03/05/20)
Kernel Version: Linux 4.4.215 #1056 Thu Mar 5 07:59:37 +04 2020 armv7l

Hi, i made factory defaults. Samba doesn't work. I cannot access to shared folders via Windows 10 even Android. Is there any way to get it working?

I tried all version of the protokol. Sometimes it was working on Android 10, but very slowly. I tried to enable smb1.0 on Windows 10 1909, but without success. I have to switch back to build r41986.

thank you

[claudinei]

[PITABoy]

I just got a brand new ASUS RT-AC5300 and flashed dd-wrt with this build... most everything seems to be working however the WAN MAC is 00:00:00:00:00:01 which is obviously wrong. Internet still works though.


EDIT: I used the ASUS recovery to reset factory settings then dd-wrt to reset factory settings and now the mac is correct. Hope that this helps.

[danielwritesback]

AC routers: Upper and lower are backwards in the 5ghz menu (cosmetic).
Workaround: Choose the reverse.

ARM specific: TurboQam on by default, no settings in menu.
Workaround: nvram set wl0_turbo_qam=0 && nvram set wl1_turbo_qam=0 && nvram commit

ARM specific: CPU governor is missing
Workaround: A fan

And some good news:
I see well-working multicast features.

[egc]

[d0d0]

Router Model: Netgear R6400v2
board_id: U12H332T20
Firmware Version : DD-WRT v3.0-r42617 std (03/05/20)
Kernel Version: Linux 4.4.215 #1052 SMP Wed Mar 4 12:16:22 +04 2020 armv7l
Previous: r42602 std (03/03/20)
Reset: No

Status: Working
basic setup, static leases,inbuilt dnscrypt,OpenVPN client with PBR(expressvpn),USB storage NAS working,ad-blocking script by SurprisedItWorks


Problem: sometimes OpenVPN stopped working, there is no traffic
openvpn option under status menu is completely blanked however, if i try to apply openvpn Client settings from service menu then openvpn is not starting up openvpn status windows is still blanked
only way to get it back either i have to reboot my router or from CLI restart_f openvpn then vpn is back & working

syslog
grep -i err /var/log/messages

[egc]

Anything in syslog?

[d0d0]

[d0d0]

[egc]

Please start a new thread post screenshot of the Openvpn setup page and your settings in Additional Config.
Add verb 5 to additional config of openvpn client setting, reboot and post openvpn status page ( whole page)

[stephensuley]

Router Model: Asus RT-AC87U
Firmware Version: DD-WRT v3.0-r42617 std (03/05/20)
Kernel Version: Linux 4.4.215 #1056 Thu Mar 5 07:59:37 +04 2020 armv7l

using wl0 only.

Notes: After the successful upgrade the client bridge mode will not function at all. No TX no RX. No connection. I've tried factory reset and hard reset. No change.

If i set network mode to AP, as a test, it seems to work fine, i can see the SSID and connect. however if I switch it back to client bridge nothing.

This has been working as client bridge device for years...it must be something recent.

Any ideas?

[kernel-panic69]

From the OP: