Joined: 08 May 2018 Posts: 14246 Location: Texas, USA
Posted: Tue Jan 21, 2020 21:59 Post subject: New Build 42054: 01-21-2020-r42054
WARNING:DO NOT flash this experimental test build unless you know the risks and recovery methods. Report here to provide important info for developers and users. Always state your hardware model & version, mode (e.g. Repeater) and SPECIFIC build (e.g. netgear-r7000-webflash). Avoid discussions and create a new thread for specific problems or questions as this thread is not for support, and posts may be deleted or moved.
Important: if reporting any issues, provide applicable info (GUI syslog, `dmesg`, `cat /var/log/messages`, etc.)
Or put into SVN ticket. For firewall issues, also provide "iptables" info (`iptables -L`, `iptables -t nat -L`, & the /tmp/.ipt file).
Issues, observations, and/or workarounds reported: 1. DNScrypt is mostly only using v2 protocols now, but requires Golang that DD can't use:6246 2. WDS does not work on Broadcom ARM devices (only MIPS<->MIPS) 3. VAPs not working at bootfixed for unbridged VAPs with r40564:40566.Workaround startup command: sleep 10;stopservice nas;stopservice wlconf;startservice wlconf;startservice nas(there are a few alternatives to search)
Notes: 1. SFE accelerated NAT is in 33006+ builds but only in kernel 3.2 and newer 2. 'KRACK' vulnerability fixes were completed in r33678 for Broadcom, including k26 (33655) & k24 (33656); use 33772 or later.
3. Bridge modes on k4.4 devices may sometimes work in some configurations in certain builds but are not supported by the bcmdhd driver. Use client or repeater instead as WDS doesn't work with Broadcom ARM either (see Issues below).
4. PBR/UDP with SFE working again since r40513 (see 6729)
5. CAKE scheduler changes "completed" with r41057 (see 5796) & FQ_CODEL_FAST with r41027 (reset first!)
6. Reset button was broken in 40571; fixed in build 40750.
7. Radio Timer / GTK Renewal issues, syslog spam and wireless issues (BCM MIPS) fixed with r41662 8. New Broadcom build option for 8MB+ K2.x devices (limited currently):
broadcom_K3X_mipsel32r1 [BS has tested on a WRT600N v1.1]
9. CVE-2019-14899 VPN fix (r41784: applicability depends on VPN setup) and GUI toggle (r41812): ticket 6920, 6928, 6931, 6932
Template example to copy (after "Code:") for posting issues, be sure to include the mode in use (gateway, AP, CB, etc.):
Posted: Tue Jan 21, 2020 22:33 Post subject: Netgear Nighthawk R7000
Router/Version: Netgear R7000 Firmware: DD-WRT v3.0-r42054 std (01/21/20) Kernel: Linux 4.4.210 #736 SMP Mon Jan 20 10:27:54 +04 2020 armv7l Mode: Gateway Reset: No Previous: 01-18-2020-r42015 Status: Working, Samba Issues.
Dec 31 16:00:13 R7000 local5.err smbd: [smbd-worker/1087]: ERROR: Can't open `/tmp/smb.db': No such file or directory
Dec 31 16:00:13 R7000 local5.err smbd: [smbd-worker/1087]: ERROR: User database file does not exist. Only guest sessions (if permitted) will work.
Router/Version: Netgear R7000
Firmware: DD-WRT v3.0-r42054 std (01/21/20)
Kernel: Linux 4.4.210 #736 SMP Mon Jan 20 10:27:54 +04 2020 armv7l
Previous: r42015
Mode/Status: Gateway / working
Reset: no
Issues/Errors: Working well so far.
Uptime: 55min
Temperatures: CPU 63.6 °C / WL0 46.0 °C / WL1 52.0 °C
Router/Version: R7000
Mode: AP
File: 42054
Status: Loaded, working with issue
Issue: Last 2 builds not working properly Samba. I try to nvram reset, differents settings; min NT 1.0, max: SMB 2 or SMB 3.11... and no luck. Win 10 and my TV Panasonic on Firefox OS do not see HDD connected to R7000 on builds 42015 and 42054. So I reverted back to 41986, when the Samba work perfect with min NT 1.0 and max SMB 2 on both win 10 PC and TV Panasonic on Firefox OS.
Maybe need some other special settings to get working Samba?
Joined: 16 Mar 2019 Posts: 353 Location: Szczecin, Poland EU
Posted: Wed Jan 22, 2020 10:13 Post subject: New Build 42054: 01-21-2020-r42054
Router/Version: Netgear WNR3500L v2
Mode: Internet gateway and WIFI AP
File: dd-wrt.v24-42054_NEWD-2_K3.x_mega-WNR3500Lv2
Kernel: Linux 3.10.108-d9 #1694 Tue Jan 21 17:20:58 +04 2020 mips
Status: OK
Reset: No
Uptime: almost 12h
Router is updated via ssh. No problems after reboot. Previous problems with DNS services look like fix. I don't see any issues actually.
Joined: 08 May 2018 Posts: 14246 Location: Texas, USA
Posted: Wed Jan 22, 2020 15:28 Post subject: Re: Samba
al_bo wrote:
Router/Version: R7000
Mode: AP
File: 42054
Status: Loaded, working with issue
Issue: Last 2 builds not working properly Samba. I try to nvram reset, differents settings; min NT 1.0, max: SMB 2 or SMB 3.11... and no luck. Win 10 and my TV Panasonic on Firefox OS do not see HDD connected to R7000 on builds 42015 and 42054. So I reverted back to 41986, when the Samba work perfect with min NT 1.0 and max SMB 2 on both win 10 PC and TV Panasonic on Firefox OS.
Maybe need some other special settings to get working Samba?
BrainSlayer had changed minimum protocol to 2.1 somewhere along the way, but not sure if it was reverted or not on Broadcom. I saw reports that it was reverted on Marvell, so I thought it was across the board. I would have to go back and look through the commits. _________________ "Life is but a fleeting moment, a vapor that vanishes quickly; All is vanity"
Contribute To DD-WRT Pogo - A minimal level of ability is expected and needed... DD-WRT Releases 2023 (PolitePol)
DD-WRT Releases 2023 (RSS Everything)
----------------------
Linux User #377467 counter.li.org / linuxcounter.net
Posted: Wed Jan 22, 2020 16:25 Post subject: Re: Samba
al_bo wrote:
Router/Version: R7000
Mode: AP
File: 42054
Status: Loaded, working with issue
Issue: Last 2 builds not working properly Samba. I try to nvram reset, differents settings; min NT 1.0, max: SMB 2 or SMB 3.11... and no luck. Win 10 and my TV Panasonic on Firefox OS do not see HDD connected to R7000 on builds 42015 and 42054. So I reverted back to 41986, when the Samba work perfect with min NT 1.0 and max SMB 2 on both win 10 PC and TV Panasonic on Firefox OS.
Maybe need some other special settings to get working Samba?
I had exactly the same issue on r42015 and had tried for a long time to re-do the configuration in Services for USB & Samba but, USB drive was not getting recognized at all so...
Had to revert to previous r41986 and my backup configuration file.
Router/Version: Netgear R7000 Mode: Router/Gateway File: v3.0-r42054 std Kernel: Linux 4.4.210 #736 SMP Mon Jan 20 10:27:54 +04 2020 armv7l Status: Working (Including USB & SAMBA with min Protocol Ver SMB 2)
Uptime: 15 minutes
Router/Version: Asus RT-AC68U rev C1
Mode: Gateway / AP
Kernel: Linux 4.4.210 #736 SMP Mon Jan 20 10:27:54 +04 2020 armv7l
Reset: No, flashed from CLI
Status: Working well! _________________ Netgear R7000 on Build 55109
Asus AC-AC68U rev. C1 (AP) on Build 55109
Asus AC-68U rev. A1 on Build 54604
Asus AC-68U rev. A1 on Build 53339
Was receiving "max network open connections met" on the 1/9/2020 build. Haven't had any on the 1/21/2020 build yet. However, unsure if this is related to dd-wrt or another issue.
Router/Version: Asus RT-AC68U Mode: AP Status: SMB Share not reachable
Hi,
update from DD-WRT v3.0-r41586 std (11/21/19) to this build. After installing the update Infuse is not able to connect to my NAS drive which is connected to my AC68U. Infuse finds the share but it couldn't connect.
With my Macbook pro everything works well when connecting to DD-WRT Nas.
Switched back to DD-WRT v3.0-r41586 std (11/21/19) and Infuse can also connect
Router/Version: Netgear R6400
Firmware: DD-WRT v3.0-r42054 std (01/21/20)
Kernel: Linux 4.4.210 #736 SMP Mon Jan 20 10:27:54 +04 2020 armv7l
Previous: 01-09-2020-r41954
Mode/Status: Gateway AP / working
Reset: no, upgraded via GUI.
Issues/Errors: Working well so far.
Uptime: 23:10
Temperatures: CPU 48.0 °C / WL0 35.1 °C
