Joined: 08 May 2018 Posts: 14246 Location: Texas, USA
Posted: Sat Jan 18, 2020 14:22 Post subject: New Build 42015: 01-18-2020-r42015
WARNING:DO NOT flash this experimental test build unless you know the risks and recovery methods. Report here to provide important info for developers and users. Always state your hardware model & version, mode (e.g. Repeater) and SPECIFIC build (e.g. netgear-r7000-webflash). Avoid discussions and create a new thread for specific problems or questions as this thread is not for support, and posts may be deleted or moved.
Important: if reporting any issues, provide applicable info (GUI syslog, `dmesg`, `cat /var/log/messages`, etc.)
Or put into SVN ticket. For firewall issues, also provide "iptables" info (`iptables -L`, `iptables -t nat -L`, & the /tmp/.ipt file).
Issues, observations, and/or workarounds reported: 1. DNScrypt is mostly only using v2 protocols now, but requires Golang that DD can't use:6246 2. WDS does not work on Broadcom ARM devices (only MIPS<->MIPS) 3. VAPs not working at bootfixed for unbridged VAPs with r40564:40566.Workaround startup command: sleep 10;stopservice nas;stopservice wlconf;startservice wlconf;startservice nas(there are a few alternatives to search)
Notes: 1. SFE accelerated NAT is in 33006+ builds but only in kernel 3.2 and newer 2. 'KRACK' vulnerability fixes were completed in r33678 for Broadcom, including k26 (33655) & k24 (33656); use 33772 or later.
3. Bridge modes on k4.4 devices may sometimes work in some configurations in certain builds but are not supported by the bcmdhd driver. Use client or repeater instead as WDS doesn't work with Broadcom ARM either (see Issues below).
4. PBR/UDP with SFE working again since r40513 (see 6729)
5. CAKE scheduler changes "completed" with r41057 (see 5796) & FQ_CODEL_FAST with r41027 (reset first!)
6. Reset button was broken in 40571; fixed in build 40750.
7. Radio Timer / GTK Renewal issues, syslog spam and wireless issues (BCM MIPS) fixed with r41662 8. New Broadcom build option for 8MB+ K2.x devices (limited currently):
broadcom_K3X_mipsel32r1 [BS has tested on a WRT600N v1.1]
9. CVE-2019-14899 VPN fix (r41784: applicability depends on VPN setup) and GUI toggle (r41812): ticket 6920, 6928, 6931, 6932
Template example to copy (after "Code:") for posting issues, be sure to include the mode in use (gateway, AP, CB, etc.):
Router/Version: Netgear R6400v1
File: netgear-r6400-webflash.bin
Firmware: DD-WRT v3.0-r42015 std (01/18/20)
Kernel: Linux 4.4.210 #709 SMP Fri Jan 17 10:13:50 +04 2020 armv7I
Mode: AP/USB/NAS/GATEWAY/FORWARDING/RESERVED IP
Previous: r41954
Reset?: N
Status: Samba status is stopped. USB mounts but unable to get Samba to start. Reboot or re-enable Samba has no affect. Reverting back to r41954 and Samba works.
Router: Netgear R7000P
Kernel: Linux 4.4.210 #714 SMP Sat Jan 18 09:28:49 +04 2020 armv7l
Mode: Gateway/AP 2.4GHz 5GHz IPv6 static leases Unbound JFFS2
Status: up 4hrs all seems well
Joined: 08 May 2018 Posts: 14246 Location: Texas, USA
Posted: Sat Jan 18, 2020 18:25 Post subject:
martin-s wrote:
Status: Samba status is stopped. USB mounts but unable to get Samba to start. Reboot or re-enable Samba has no affect. Reverting back to r41954 and Samba works.
The webUI is in error, perhaps. Did you telnet / ssh in and verify with ps?
Joined: 16 Mar 2019 Posts: 353 Location: Szczecin, Poland EU
Posted: Sat Jan 18, 2020 18:44 Post subject: New Build 42015: 01-18-2020-r42015
Router/Version: Netgear WNR 3500L v2
Mode: Internet gateway and WIFI AP
File: dd-wrt.v24-42015_NEWD-2_K3.x_mega-WNR3500Lv2
Kernel: Linux 3.10.108-d9 #1604 Sat Jan 18 14:29:43 +04 2020 mips
Status: OK, but issues.
1) DNS service working correctly only when DHCP server for lan is enabled. When disable DHCP, DNS service totally stop working. This problem is since build: #41986.
2) I'm update device from version #41954 to #42015 and when I'm restart router via ssh and reboot command WAN port won't transmit any signal. Netgear was reply for LAN ping and generally device was operate, but Internet signal isn't provide to Netgear. I'm especially check this problem and ISP modem transmit the internet signal correctly, but Netgear can't work on WAN interface. Probably is problem with DD-WRT firmware. I'm make restore factory defaults for Netgear and make configuration one more time. Generally router work currently and transmit internet to my devices, but it was some problems after update.
Last edited by thommy181 on Sat Jan 18, 2020 19:09; edited 1 time in total
Netgear WNDR4000: 2.4GHz CB -> 5GHz AP + VAP
File: nv64k.bin: DD-WRT v3.0-r42015 mega (01/18/20)
Kernel: Linux 3.10.108-d9 #1620 Sat Jan 18 14:45:18 +04 2020 mips
Status: Working, I changed the 5GHz channel and wasn't seeing the SSIDs, but a reboot fixed it and connects fine. Not sure if it was working before the channel change.
I pinged BS about the CLI update failing with "Bad trx header" and he said it needs the trailed build. I thought about trying that, but my 4500v2 updates fine w/ the non-trailed .bin file. Oh well. _________________ #NAT/SFE/CTF: limited speed w/ DD#Repeater issues#DD-WRT info: FAQ, Builds, Types, Modes, Changes, Demo#
OPNsense x64 5050e ITX|DD: DIR-810L, 2*EA6900@1GHz, R6300v1, RT-N66U@663, WNDR4000@533, E1500@353,
WRT54G{Lv1.1,Sv6}@250|FreshTomato: F7D8302@532|OpenWRT: F9K1119v1, RT-ACRH13, R6220, WNDR3700v4
Last edited by jwh7 on Sat Jan 18, 2020 21:18; edited 1 time in total
Posted: Sat Jan 18, 2020 21:04 Post subject: RE: Samba not working
kernel-panic69 - Thanks for the hint...
PS shows Samba running, GUI shows enabled-stopped.
Samba can be accessed from Win10 PC by IP address only (not by router name). XP PC can no longer access Samba drive - gets Data Error (CRC) when drive mapping attempted. Min=NT 1.0, Max=SMB 2. Samba server string, workgroup, user, password are all configured. This configuration has been tested and working in r41954.
Router/Version: Netgear R7000
Firmware: DD-WRT v3.0-r42015 std (01/18/20)
Kernel: Linux 4.4.210 #709 SMP Fri Jan 17 10:13:50 +04 2020 armv7l
Previous: r41986
Mode/Status: Gateway / working
Reset: no
Issues/Errors: Working well so far.
Uptime: 1hr 37min
Temperatures: CPU 64.7 °C / WL0 46.3 °C / WL1 52.4 °C
Router/Version: Netgear R8000
Firmware: DD-WRT v3.0-r42015 std (01/18/20)
Kernel: Linux 4.4.210 #709 SMP Fri Jan 17 10:13:50 +04 2020 armv7l
Previous: KONG 40270
Mode: AP
Status: Working
Reset: Just about to
Best BS Build I've had for the R8000 so far, getting loads of noise on the 2.4 radio, just rebooting to see if it'll sort itself out.
Solved the noise on the 2.4 radio through a Channel change, however both 5g radios are stuck in auto, annoying but doesn't seem to be an issue interims of bandwidth.