Important: if reporting any issues, provide applicable info (GUI syslog, `dmesg`, `cat /var/log/messages`, etc.)
Or put into SVN ticket. For firewall issues, also provide "iptables" info (`iptables -L`, `iptables -t nat -L`, & the /tmp/.ipt file).
Template to copy (after "Code:") for posting issues, be sure to include the mode in use (gateway, AP, CB, etc.):
WARNING:This thread is to report on flashing this experimental test build, providing important info for both developers and users. Always state your hardware model, version, mode (e.g. Repeater) and SPECIFIC build (e.g. 33555_NEWD-2_K3.x_mega-nv64k.bin). Please avoid discussions and create a new thread to discuss specific problems or questions, as this thread is for reporting, not support. Posts may be deleted or moved to keep this thread manageable and useful. If you don't understand the risks or what to flash and how, with a means of recovery if it bricks, do NOT flash this experimental test build. _________________ "Life is but a fleeting moment, a vapor that vanishes quickly; All is vanity"
Contribute To DD-WRT Pogo - A minimal level of ability is expected and needed... DD-WRT Releases 2023 (PolitePol)
DD-WRT Releases 2023 (RSS Everything)
----------------------
Linux User #377467 counter.li.org / linuxcounter.net
Router/Version: Linksys EA8500
Mode: Router/OpenVPN client
File: linksys-ea8500/dd-wrt-webupgrade.bin
Kernel: Linux DD-WRT-ea 4.9.200 #488 SMP Sun Nov 10 20:50:18 CET 2019 armv7l DD-WRT
Status: Working
Router/Version: Linksys EA8500
Mode: Router/OpenVPN client
File: linksys-ea8500/dd-wrt-webupgrade.bin
Kernel: Linux DD-WRT-ea 4.9.200 #488 SMP Sun Nov 10 20:50:18 CET 2019 armv7l DD-WRT
Status: Working
My 8500 is also working normally again now after updating to this build.
Posted: Wed Nov 13, 2019 14:42 Post subject: Netgear X10 r9000
Router Model: Netgear x10 r9000
Reset: No
File: DD-WRT v3.0-r41517 std (11/11/19)
Kernel: Linux 4.9.200 #397 SMP Mon Nov 11 05:51:10 CET 2019 armv7l
Status: Very Good!
Updated from r41469 > r41517 via GUI
This build is GREAT (for my use-case scenario)! The SAMBA Service is actually started upon boot! I am also receiving the best WiFi speeds from my clients in longer than I can remember!
Router/Version: Linksys EA8500
Mode: Access Point & switch
Kernel: Linux 4.9.200 #488 SMP Sun Nov 10 20:50:18 CET 2019 armv7l
Status: Up
Reset NO
Uptime just over two hours.. Generally I like to do a clean install but today I just went over top r41399, we’ll see what happens tomorrow after the wireless scheduler runs.
Update: wireless scheduler was unable to restart the wireless at 0600. Unlike on build r41468 I was able to restart the wireless by disabling the scheduler. I will default the router and try it again. if the scheduler fails again I'll revert to older build
Update-2: reset & re-flashed, uptime just under 3 hours. If I don’t update post again tomorrow that means all is good. in the meantime good range and speed on both bands so no complaints there...
Final update: Radio Scheduling is broken. Today again after yesterday’s clean install of build r41517 wireless did not restart at 0600. This build is done
Last edited by 05dyna on Fri Nov 15, 2019 12:10; edited 3 times in total