Author
Message
ic2d DD-WRT Novice Joined: 08 Oct 2019 Posts: 3
Posted: Tue Oct 08, 2019 16:56 Post subject: Linksys EA8500 bricked :( Help recover using TTL
Hello, my router is bricked tried to use the DD wrt instruction to debrick it, but after "restart" it does nothing, just booting back
In putty i see this when switching on the router:
Code: U-Boot 2012.07 [Standard IPQ806X.LN,r40331] (Oct 12 2015 - 17:00:55)
CBT U-Boot ver: 1.0.12
smem ram ptable found: ver: 0 len: 5
DRAM: 491 MiB
NAND: SF: Unsupported manufacturer 00
ipq_spi: SPI Flash not found (bus/cs/speed/mode) = (0/0/48000000/0)
128 MiB
MMC:
PCI0 Link Intialized
PCI1 Link Intialized
In: serial
Out: serial
Err: serial
cdp: get part failed for 0:HLOS
Net: MAC1 addr:0:3:7f:ba:db:1
athrs17_reg_init: complete
athrs17_vlan_config ...done
S17c init done
MAC2 addr:0:3:7f:ba:db:2
eth0
Warning: eth0 MAC addresses don't match:
Address in SROM is 00:03:7f:ba:db:01
Address in environment is 00:06:3b:01:41:00
, eth1
Hit any key to stop autoboot: 0
MMC Device 0 not found
MMC Device 0 not found
setenv - set environment variables
Write Reg: 0x00000660: Oldval = 0x00140020 Newval = 0x0014007e
Write Reg: 0x0000066c: Oldval = 0x0014005c Newval = 0x0014007d
Write Reg: 0x00000678: Oldval = 0x0014005a Newval = 0x0014007b
Write Reg: 0x00000684: Oldval = 0x00140056 Newval = 0x00140077
Write Reg: 0x00000690: Oldval = 0x0014004e Newval = 0x0014006f
Write Reg: 0x0000069c: Oldval = 0x00140001 Newval = 0x0014005f
Write Reg: 0x000006a8: Oldval = 0x0014001e Newval = 0x0014003f
Write Reg: 0x00000420: Oldval = 0x00020001 Newval = 0x00010001
Write Reg: 0x00000428: Oldval = 0x00010001 Newval = 0x00010001
Write Reg: 0x00000430: Oldval = 0x00010001 Newval = 0x00010001
Write Reg: 0x00000438: Oldval = 0x00010001 Newval = 0x00010001
Write Reg: 0x00000440: Oldval = 0x00010001 Newval = 0x00010001
Write Reg: 0x00000448: Oldval = 0x00020001 Newval = 0x00010001
Write Reg: 0x00000450: Oldval = 0x00010001 Newval = 0x00010001
(IPQ) #
TFTP launched, copying commands to flash the router.
Code: (IPQ) # setenv image ddwrt.img
setenv image ddwrt.img
(IPQ) # setenv ipaddr 192.168.1.1
setenv ipaddr 192.168.1.1
(IPQ) # setenv serverip 192.168.1.2
setenv serverip 192.168.1.2
(IPQ) # run flashimg
run flashimg
Mac1 unit failed
Using eth1 device
TFTP from server 192.168.1.2; our IP address is 192.168.1.1
Filename 'ddwrt.img'.
Load address: 0x42000000
Loading: #################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#####################################################
done
Bytes transferred = 38940927 (25230ff hex)
NAND erase: device 0 offset 0xf80000, size 0x2800000
Erasing at 0x3760000 -- 100% complete.
OK
NAND write: device 0 offset 0xf80000, size 0x25230ff
39059456 bytes written: OK
(IPQ) # run flashimg2
run flashimg2
Using eth1 device
TFTP from server 192.168.1.2; our IP address is 192.168.1.1
Filename 'ddwrt.img'.
Load address: 0x42000000
Loading: #################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#####################################################
done
Bytes transferred = 38940927 (25230ff hex)
NAND erase: device 0 offset 0x3780000, size 0x2800000
Erasing at 0x5f60000 -- 100% complete.
OK
NAND write: device 0 offset 0x3780000, size 0x25230ff
39059456 bytes written: OK
(IPQ) #
Now, i need to restart the router using command Reset, the router will reboot and run the DDWRT, but...
Code: (IPQ) # reset
reset
resetting ...
Resetting with watch dog!
U-Boot 2012.07 [Standard IPQ806X.LN,r40331] (Oct 12 2015 - 17:00:55)
CBT U-Boot ver: 1.0.12
smem ram ptable found: ver: 0 len: 5
DRAM: 491 MiB
NAND: SF: Unsupported manufacturer 00
ipq_spi: SPI Flash not found (bus/cs/speed/mode) = (0/0/48000000/0)
128 MiB
MMC:
PCI0 Link Intialized
PCI1 Link Intialized
In: serial
Out: serial
Err: serial
cdp: get part failed for 0:HLOS
Net: MAC1 addr:0:3:7f:ba:db:1
athrs17_reg_init: complete
athrs17_vlan_config ...done
S17c init done
MAC2 addr:0:3:7f:ba:db:2
eth0
Warning: eth0 MAC addresses don't match:
Address in SROM is 00:03:7f:ba:db:01
Address in environment is 00:06:3b:01:41:00
, eth1
Hit any key to stop autoboot: 0
MMC Device 0 not found
MMC Device 0 not found
setenv - set environment variables
Write Reg: 0x00000660: Oldval = 0x00140020 Newval = 0x0014007e
Write Reg: 0x0000066c: Oldval = 0x0014005c Newval = 0x0014007d
Write Reg: 0x00000678: Oldval = 0x0014005a Newval = 0x0014007b
Write Reg: 0x00000684: Oldval = 0x00140056 Newval = 0x00140077
Write Reg: 0x00000690: Oldval = 0x0014004e Newval = 0x0014006f
Write Reg: 0x0000069c: Oldval = 0x00140001 Newval = 0x0014005f
Write Reg: 0x000006a8: Oldval = 0x0014001e Newval = 0x0014003f
Write Reg: 0x00000420: Oldval = 0x00020001 Newval = 0x00010001
Write Reg: 0x00000428: Oldval = 0x00010001 Newval = 0x00010001
Write Reg: 0x00000430: Oldval = 0x00010001 Newval = 0x00010001
Write Reg: 0x00000438: Oldval = 0x00010001 Newval = 0x00010001
Write Reg: 0x00000440: Oldval = 0x00010001 Newval = 0x00010001
Write Reg: 0x00000448: Oldval = 0x00020001 Newval = 0x00010001
Write Reg: 0x00000450: Oldval = 0x00010001 Newval = 0x00010001
(IPQ) #
Now, im stuck..I dont know what do...Go and buy another router, and throw this out?! Can someone help?
Oh, also, maybe this will be needed...printenv
Code: (IPQ) # printenv
printenv
altkern=3780000
auto_recovery=no
autostart=no
baudrate=115200
boot_part=1
boot_part_ready=2
boot_ver=1.0.12
bootargs=console=ttyHSL1,115200n8 ubi.mtd=rootfs root=mtd:ubi_rootfs rootfstype=squashfs ubi.mtd=rootfs root=mtd:ubi_rootfs rootfstype=squashfs ubi.mtd=rootfs root=mtd:ubi_rootfs rootfstype=squashfs ubi.mtd=rootfs root=mtd:ubi_rootfs rootfstype=squashfs
bootcmd=bootipq
bootdelay=5
ethact=eth0
ethaddr=00:06:3b:01:41:00
fileaddr=42000000
filesize=1960000
flashimg=tftp $loadaddr $image;nand erase $prikern $imgsize;nand write $loadaddr $prikern $filesize
flashimg2=tftp $loadaddr $image;nand erase $altkern $imgsize;nand write $loadaddr $altkern $filesize
fsbootargs=ubi.mtd=rootfs root=mtd:ubi_rootfs rootfstype=squashfs
image=orig.eu.1.1.9.img
imgsize=2800000
ipaddr=192.168.1.1
loadaddr=42000000
machid=1260
mtddevname=fs
mtddevnum=0
mtdids=nand0=nand0
mtdparts=mtdparts=nand0:0x2500000@0x1280000(fs),
netmask=255.255.255.0
partbootargs=console=ttyHSL1,115200n8 init=/sbin/init rootfstype=squashfs root=31:14
partbootargs2=console=ttyHSL1,115200n8 init=/sbin/init rootfstype=squashfs root=31:16
partition=nand0,0
prikern=f80000
serverip=192.168.1.2
stderr=serial
stdin=serial
stdout=serial
Environment size: 1272/262140 bytes
(IPQ) #
Back to top
Sponsor
PowerPoldi DD-WRT User Joined: 15 Oct 2016 Posts: 70
Posted: Sun Oct 13, 2019 15:11 Post subject:
EA8500 is powered by Qualcomm SOC.
Better ask this thread in the Atheros-Section!
Back to top
Malachi DD-WRT Guru Joined: 17 Jul 2012 Posts: 7209 Location: Columbus, Ohio
Posted: Sun Oct 13, 2019 18:31 Post subject:
Moved to the correct forum. _________________ I am far from a guru, I'm barely a novice.
Back to top
mrjcd DD-WRT Guru Joined: 31 Jan 2015 Posts: 6291 Location: Texas
Posted: Sun Oct 13, 2019 19:23 Post subject: Re: Linksys EA8500 bricked :( Help recover using TTL
ic2d wrote: Filename 'ddwrt.img'.
What exact build number and file name of the DD-WRT firmware you used
Back to top
mrjcd DD-WRT Guru Joined: 31 Jan 2015 Posts: 6291 Location: Texas
Posted: Sun Oct 13, 2019 20:27 Post subject: Re: Linksys EA8500 bricked :( Help recover using TTL
The reason I ask about the exact firmware you used ----
ic2d wrote: .... #####################################################
done
Bytes transferred = 38940927 (25230ff hex) ...
Seems to me you may have used an older firmware from main DD-WRT ...which will NOT work
see ---
https://forum.dd-wrt.com/phpBB2/viewtopic.php?p=1177889#1177889
Prolly best just use instructions from 'THIS PAGE'
all you need to install DD-WRT is on that page.
good luck
Back to top
ic2d DD-WRT Novice Joined: 08 Oct 2019 Posts: 3
Posted: Wed Oct 16, 2019 12:58 Post subject:
Thanks to all for your reply. My problem was with env's. Bootargs was wrong.
Now router i running fine. default prinenv for now is
auto_recovery=yes
autostart=yes
baudrate=115200
boot_part=1
boot_part_ready=3
boot_ver=1.0.12
bootargs=console=ttyHSL1,115200n8 init=/sbin/init rootfstype=squashfs root=31:14
bootcmd=bootipq
bootdelay=2
ethact=eth0
ethaddr=00:06:3b:01:41:00
flashimg=tftp $loadaddr $image;nand erase $prikern $imgsize;nand write $loadaddr $prikern $filesize
flashimg2=tftp $loadaddr $image;nand erase $altkern $imgsize;nand write $loadaddr $altkern $filesize
fsbootargs=ubi.mtd=rootfs root=mtd:ubi_rootfs rootfstype=squashfs
image=wraith.bin
imgsize=2800000
ipaddr=192.168.1.1
loadaddr=42000000
machid=1260
netmask=255.255.255.0
partbootargs=console=ttyHSL1,115200n8 init=/sbin/init rootfstype=squashfs root=31:14
partbootargs2=console=ttyHSL1,115200n8 init=/sbin/init rootfstype=squashfs root=31:16
prikern=f80000
serverip=192.168.1.254
stderr=serial
stdin=serial
stdout=serial
Back to top