New build: 08-06-2019-r40559

Post new topic   Reply to topic    DD-WRT Forum Forum Index -> Marvell MVEBU based Hardware (WRT1900AC etc.)
Goto page Previous  1, 2, 3  Next
Author Message
kernel-panic69
DD-WRT Guru


Joined: 08 May 2018
Posts: 2683
Location: Texas, USA

PostPosted: Thu Aug 08, 2019 2:07    Post subject: Reply with quote
gufus wrote:
Aug 7 16:52:31 DD-WRT b7:f8:e1 daemon.info httpd[1849]: httpd : Authentication fail
Aug 7 16:52:31 DD-WRT b7:f8:e1 daemon.err httpd[1849]: httpd : Request Error Code 401: Authorization required. please note that the default username is "root" in all newer releases


These error messages never seem to go away. Are they coming up when you connect via wi-fi or wired? Did you set another username for webUI access besides root?
Sponsor
WENED
DD-WRT User


Joined: 30 May 2017
Posts: 329
Location: Rural Manitoba

PostPosted: Thu Aug 08, 2019 3:12    Post subject: Reply with quote
kernel-panic69 wrote:
gufus wrote:
Aug 7 16:52:31 DD-WRT b7:f8:e1 daemon.info httpd[1849]: httpd : Authentication fail
Aug 7 16:52:31 DD-WRT b7:f8:e1 daemon.err httpd[1849]: httpd : Request Error Code 401: Authorization required. please note that the default username is "root" in all newer releases


These error messages never seem to go away. Are they coming up when you connect via wi-fi or wired? Did you set another username for webUI access besides root?


A few days ago I got annoyed with these messages so I changed my username to root. It did not help. I monitor all my routers on IE11 as it is simple since I don't use IE11 for anything else and can setup my home page to all my routers. Everytime however I start IE11 it seems to cause the errors to appear. I can make changes, reboot, etc. without incident but if I close IE11 and restart, oops there's my redline. If I sign in with EDGE, the same result.

_________________
WRT3200acm Master WDS 5GHz 80Mhz r41491
WRT3200acm WDS Station r41491
WRT1900Ac V1 WDS AP 5Ghz r41491 (Defective, no 2.4Ghz but 5Ghz works great)
WRT1900AC V1 WDS Station r41491
WRT1900AC V1 SPARE r41418
WRT1200AC V1 Client-Bridge r35898
WRT54G DD-WRT v3.0-r37305 micro Client-Bridged for 1 IP Camera
EX6200 DD-WRT r38535 - Spare
EX7000 Stock Firmware Spare
Devices and Cameras and Sensors
15 WiFi cameras, 4 desktops, 2 laptop, 12 Sonoff Basic/TH16, Artisan 700 Printer, Ongoing testing of other devices.
kernel-panic69
DD-WRT Guru


Joined: 08 May 2018
Posts: 2683
Location: Texas, USA

PostPosted: Thu Aug 08, 2019 3:52    Post subject: Reply with quote
WENED wrote:
A few days ago I got annoyed with these messages so I changed my username to root. It did not help. I monitor all my routers on IE11 as it is simple since I don't use IE11 for anything else and can setup my home page to all my routers. Everytime however I start IE11 it seems to cause the errors to appear. I can make changes, reboot, etc. without incident but if I close IE11 and restart, oops there's my redline. If I sign in with EDGE, the same result.


Sounds like a Microsuck problem, perhaps. You don't have to change the username for the webUI, just the password. I had these errors with non-Microsuck browsers when I kept setting the username to 'admin' way back before my first brick. Haven't seen this error message in quite some time since I quit doing that that I recall. I just wish the ntp update was closer to every 24 hours than every damn hour.
gufus
DD-WRT Guru


Joined: 04 Aug 2012
Posts: 610
Location: behind the screen

PostPosted: Thu Aug 08, 2019 15:40    Post subject: Reply with quote
kernel-panic69 wrote:
gufus wrote:
Aug 7 16:52:31 DD-WRT b7:f8:e1 daemon.info httpd[1849]: httpd : Authentication fail
Aug 7 16:52:31 DD-WRT b7:f8:e1 daemon.err httpd[1849]: httpd : Request Error Code 401: Authorization required. please note that the default username is "root" in all newer releases


These error messages never seem to go away. Are they coming up when you connect via wi-fi or wired? Did you set another username for webUI access besides root?


changed both user name and pw to custom ones

same error with wired and wifi

same error with Google Chrome and IE

_________________
WRT3200ACM openwrt 18.06.4
WRT3200ACM dd-wrt r40009
WRT54GL dd-wrt r21676
dance85
DD-WRT User


Joined: 02 Jun 2017
Posts: 171

PostPosted: Thu Aug 08, 2019 19:09    Post subject: Reply with quote
good evening to all, but the problem of the NAS has been solved?
dyilmaz
DD-WRT Novice


Joined: 26 Aug 2016
Posts: 42

PostPosted: Thu Aug 08, 2019 20:28    Post subject: There is a bug in the openvpn client configuration page. Reply with quote
I reported this problem on forum page of the previous release firmware but I guess nobody noticed it.

If you change the ip address of your vpn server in the vpn client configuration and then if you press to the apply button, in fact it does not apply the new configuration and you have to press to the apply button one more time, otherwise it does not connect to vpn service.
shmerl
DD-WRT User


Joined: 08 Dec 2014
Posts: 77

PostPosted: Sun Aug 11, 2019 20:18    Post subject: Reply with quote
I haven't updated DD-WRT in a while on my Linksys WRT1900ACS.

Now I see all kind of comments about problems with updates and partitions. Is this still an issue?
gufus
DD-WRT Guru


Joined: 04 Aug 2012
Posts: 610
Location: behind the screen

PostPosted: Sun Aug 11, 2019 21:04    Post subject: Reply with quote
shmerl wrote:
I haven't updated DD-WRT in a while on my Linksys WRT1900ACS.

Now I see all kind of comments about problems with updates and partitions. Is this still an issue?
How about you update and let us how it went?
_________________
WRT3200ACM openwrt 18.06.4
WRT3200ACM dd-wrt r40009
WRT54GL dd-wrt r21676
SurprisedItWorks
DD-WRT Guru


Joined: 04 Aug 2018
Posts: 508
Location: Appalachian mountains, USA

PostPosted: Sun Aug 11, 2019 21:10    Post subject: Reply with quote
(Update in my second paragraph to add a DNSCrypt V2 link.)

shmerl wrote:
I haven't updated DD-WRT in a while on my Linksys WRT1900ACS.

Now I see all kind of comments about problems with updates and partitions. Is this still an issue?

Releases through 40134 fit in either partition of 1900 and older WRTs, but newer releases only fit in the first partition, apparently because of a bigger linux kernel. My impression is that the 3200s don't have this issue. Some have claimed that the CLI flashing procedure from the top of 40189 new-build thread https://forum.dd-wrt.com/phpBB2/viewtopic.php?t=320387 can handle a slightly larger build than the GUI webflash, but frankly I can't see any reason this makes sense. I've flashed both ways.

I'm on 40009, which seems to be a solid build. If you're a dnscrypt user, see my signature link on dnscrypt, as the Encrypt DNS button is gone by this release, though the underlying code is still available and will fully support dnscrypt if set up in the Startup commands. Update: Some have moved on to DNSCrypt V2, though the setup is more involved: https://forum.dd-wrt.com/phpBB2/viewtopic.php?t=320764. DNS-over-TLS has been worked out for the WRTs also: https://forum.dd-wrt.com/phpBB2/viewtopic.php?p=1166512

My understanding is that 40134 is also fairly solid, though with some issues for certain users. See the new-build post.

I'm still waiting for a build newer than 40134 that seems to be without problems. Some are brave and will try anything. I'm a big chicken, myself. As always, check out the new-build posts.

_________________
Six Linksys WRT1900ACSv2 (38159, r39144, 40009, 40784):
VLANs, multiple VAPs, NAS, QoS, client-mode travel router, OpenVPN client/PBR (old=NordVPN, new=AirVPN), two DNSCrypt servers (incl Quad9) routed through vpn.


Last edited by SurprisedItWorks on Mon Aug 12, 2019 19:45; edited 1 time in total
shmerl
DD-WRT User


Joined: 08 Dec 2014
Posts: 77

PostPosted: Sun Aug 11, 2019 21:15    Post subject: Reply with quote
gufus wrote:
How about you update and let us how it went?


That's not something I'd like to do, if there are such major issues like failing upgrades.
shmerl
DD-WRT User


Joined: 08 Dec 2014
Posts: 77

PostPosted: Sun Aug 11, 2019 21:18    Post subject: Reply with quote
SurprisedItWorks wrote:
Releases through 40134 fit in either partition of 1900 and older WRTs, but newer releases only fit in the first partition, apparently because of a bigger linux kernel. My impression is that the 3200s don't have this issue.


How exactly can this be fixed, if kernel size got bigger? Some filesystem compression?
gufus
DD-WRT Guru


Joined: 04 Aug 2012
Posts: 610
Location: behind the screen

PostPosted: Sun Aug 11, 2019 21:33    Post subject: Reply with quote
shmerl wrote:
gufus wrote:
How about you update and let us how it went?


That's not something I'd like to do, if there are such major issues like failing upgrades.
Ah

I understand Smile

My LAN runs mostly latest Firmware.

_________________
WRT3200ACM openwrt 18.06.4
WRT3200ACM dd-wrt r40009
WRT54GL dd-wrt r21676
MLandi
DD-WRT User


Joined: 04 Dec 2007
Posts: 170

PostPosted: Tue Aug 13, 2019 12:44    Post subject: Reply with quote
I am very late to the party here, a little vacation got into the way. Smile Updated to 8/6/2019, no issues
_________________
Netgear R9000 X10
DD-WRT v3.0-r41686 std (12/10/19)
AP, DNSMasq, Local DNS
CloudFlare DNS
QoS using HFSC w/CAKE
Static Leases & DHCP
2.4GHz: 3 + 7 (2422 MHz HT40)
5GHz: 161 + 155 (5805 MHz VHT80)
Xfinity 1Gbps/35Mbps
kernel-panic69
DD-WRT Guru


Joined: 08 May 2018
Posts: 2683
Location: Texas, USA

PostPosted: Tue Aug 13, 2019 14:34    Post subject: Reply with quote
gufus wrote:
kernel-panic69 wrote:
gufus wrote:
Aug 7 16:52:31 DD-WRT b7:f8:e1 daemon.info httpd[1849]: httpd : Authentication fail
Aug 7 16:52:31 DD-WRT b7:f8:e1 daemon.err httpd[1849]: httpd : Request Error Code 401: Authorization required. please note that the default username is "root" in all newer releases


These error messages never seem to go away. Are they coming up when you connect via wi-fi or wired? Did you set another username for webUI access besides root?


changed both user name and pw to custom ones

same error with wired and wifi

same error with Google Chrome and IE


Then that is why you are getting this error. This is why I got it when I set the username to 'admin' instead of 'root'. This is default behavior.
gufus
DD-WRT Guru


Joined: 04 Aug 2012
Posts: 610
Location: behind the screen

PostPosted: Tue Aug 13, 2019 19:21    Post subject: Reply with quote
kernel-panic69 wrote:
gufus wrote:
kernel-panic69 wrote:
gufus wrote:
Aug 7 16:52:31 DD-WRT b7:f8:e1 daemon.info httpd[1849]: httpd : Authentication fail
Aug 7 16:52:31 DD-WRT b7:f8:e1 daemon.err httpd[1849]: httpd : Request Error Code 401: Authorization required. please note that the default username is "root" in all newer releases


These error messages never seem to go away. Are they coming up when you connect via wi-fi or wired? Did you set another username for webUI access besides root?


changed both user name and pw to custom ones

same error with wired and wifi

same error with Google Chrome and IE


Then that is why you are getting this error. This is why I got it when I set the username to 'admin' instead of 'root'. This is default behavior.


Nope, no change

I changed the username to "root" and still get httpd error 401

_________________
WRT3200ACM openwrt 18.06.4
WRT3200ACM dd-wrt r40009
WRT54GL dd-wrt r21676
Goto page Previous  1, 2, 3  Next Display posts from previous:    Page 2 of 3
Post new topic   Reply to topic    DD-WRT Forum Forum Index -> Marvell MVEBU based Hardware (WRT1900AC etc.) All times are GMT

Navigation

 
Jump to:  
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
You cannot attach files in this forum
You cannot download files in this forum