New BS Build: r40276 (07/12/19)

Post new topic   Reply to topic    DD-WRT Forum Forum Index -> Atheros WiSOC based Hardware
Goto page 1, 2  Next
Author Message
mrjcd
DD-WRT Guru


Joined: 31 Jan 2015
Posts: 4862
Location: Texas

PostPosted: Fri Jul 12, 2019 22:19    Post subject: New BS Build: r40276 (07/12/19) Reply with quote
New BS Build: r40276 (07/12/19)

ftp://ftp.dd-wrt.com/betas/2019/07-12-2019-r40276/
or
https://download1.dd-wrt.com/dd-wrtv2/downloads/betas/2019/07-12-2019-r40276/

Please report errors or other changes with this new build release.


Release Notes:
http://svn.dd-wrt.com/timeline

Router Model:

Status:
Reset:
Errors:
Sponsor
mrjcd
DD-WRT Guru


Joined: 31 Jan 2015
Posts: 4862
Location: Texas

PostPosted: Fri Jul 12, 2019 22:24    Post subject: Reply with quote
EA8500
DD-WRT v3.0-r40276 std (07/12/19)
Linux 4.9.185 #333 SMP Wed Jul 10 12:44:18 CEST 2019 armv7l
NO-reset GUI install over r40260
main router
32 static leases
local DNS
unbound
ovpn server
samba share ext4
QOS HFSC FQ_CODEL
tis all good

#

WNDR3700v4
DD-WRT v3.0-r40276 std (07/12/19)
Linux 3.18.140 #46592 Fri Jul 12 05:06:37 CEST 2019 mips
NO reset -- GUI install over r40260
switch / ovpn server / samba share ext4
all ok

#

WRT160NL x2
DD-WRT v3.0-r40276 std (07/12/19)
Linux 3.10.108-d8 #14604 Fri Jul 12 03:10:23 CEST 2019 mips
NO reset -- GUI install over r40260

wrt160nl-firmware.bin is a bigass 7,799,808 bytes but tis good and also since https://svn.dd-wrt.com/changeset/40262
now the 160NL USB will mount to /tmp/mnt/sda1 rather than the silly /tmp/mnt/sda_part1 ... thanks BS Cool
tis all good :')

Reset & reconfig for WDS ---
I have 2 of these units currently setup with r40276 thinking of replacing my years old E2100L WDS setup.
Testing the 160NL with WDS-AP in back room wired to my local network and the WDS-Sta in office room wired to this computer.
Been tinkering with them most of the day. Looks like same ol loose wifi during sometime key renewal that I have seen on many builds for theses units over the years.
I now have both set to 'Key Renewal Interval' = 0 and that seems to fix it so far.
Been up now a couple hours. I always have Netflix going on 2nd monitor plus whatever else I'm doing on local or WAN and NOT a bleep yet. The only thing I see is this WDS seems a tad bit slower than the E200L units running r27506. Only mabybe 3 ~ 4 Mbps SLOWER and I have done everything I could think of...I even installed old r27506 on these 160NL units with same config and their wireless preformed a little better ....that made it matched my E2100L WDS setup
Prolly leave this as is and test for another day before I decide to replace the old WDS setup Wink Twisted Evil
bdg2
DD-WRT User


Joined: 18 Apr 2013
Posts: 315

PostPosted: Fri Jul 12, 2019 23:37    Post subject: WNDR3700v4 - wndr3700v4-webflash r40276.bin Reply with quote
WNDR3700v4
DD-WRT v3.0-r40276 std (07/12/19)
Linux 3.18.140 #46592 Fri Jul 12 05:06:37 CEST 2019 mips
NO reset -- GUI install over r40009
switch / WiFi access point / ovpn server / QoS on upload / Dual Stack / Guest network on br1 / PPPoE connection to modem

Hopeless.
Had trouble getting it to stay up long enough for me to revert to working firmware.
But it seemed more stable when I disconnected the modem and then I mangaged to revert to r40009.

Edit: I'm thinking maybe a problem when using PPPoE WAN connection.


Last edited by bdg2 on Sun Jul 14, 2019 0:21; edited 3 times in total
Lusitano
DD-WRT User


Joined: 25 Jun 2014
Posts: 119
Location: São Paulo - Brazil

PostPosted: Sat Jul 13, 2019 3:45    Post subject: Reply with quote


TP-Link TL-WR841ND v8

Rolling Eyes


Last edited by Lusitano on Sat Jul 13, 2019 7:23; edited 1 time in total
mrjcd
DD-WRT Guru


Joined: 31 Jan 2015
Posts: 4862
Location: Texas

PostPosted: Sat Jul 13, 2019 4:10    Post subject: Reply with quote
The r40276 WRT160NL WDS seems solid. Been up several hours now with NO problems.
I'm in the recliner with the laptap and just rsync several directories from the
desktop that's wired to the WDS-Sta......tis all good Cool
Main router EA8500 working like a pro. up 6:56
WNDR3700v4 has actually been up with r40276 17:24 and I never have a bit of trouble with him.
Wink
nickant
DD-WRT User


Joined: 09 Feb 2016
Posts: 151

PostPosted: Sat Jul 13, 2019 6:04    Post subject: Reply with quote
mrjcd:
on the EA8500, would you recommend r40276 over r39885M?
I haven't tried going from Kong to BS on my EA8500.
Do ya think it would retain settings and work, or fail like r40270M?
Yes, I know - "try it" - just out at the moment.

I also have a WNDR3700v4, as a backup, running r35531.
Tried flashing r40276 no reset, started but no internet.
Tried r40134 (slightly smaller size) - worked fine!

_________________
------------------------------------
Linksys EA8500 DD-WRT r41686 (Gateway + OpenVPN Client)
Linksys WRT1900ACv1 DD-WRT r41686 (AP)
Netgear/Telstra V7610 (spare AP)
Billion BiPAC 7800NXL (spare AP)
Netgear WNDR3700v4 DD-WRT r41369 (spare Gateway + OpenVPN Client)
Photos: https://www.flickr.com/photos/nickant44/albums
mrjcd
DD-WRT Guru


Joined: 31 Jan 2015
Posts: 4862
Location: Texas

PostPosted: Sat Jul 13, 2019 8:11    Post subject: Reply with quote
That's just up to you to try, nickant.
I run r39885M for week or so seems like without any problems.
Best I remember I run my backup main after that for while. I like to keep the 'backup up main router' up to date and with any changes I may have done within my network. I' sure I done a reset and reconfig sometime since using r39885M on it cause I also tinker with some BS test builds.

The other EA8500, one I use as switch was also prolly was reset since r39885M cause I was playin with Kong openwrt FW. However, I know it has not been reset in while now with many BS builds installed and Kong r40270M and back to BS r40276.
It hasn't caused any issues at all. I only use it as a WAN disabled, switch / ovpn server / samba share / VLAN on 2 its ports and it is nothing really important iffin I break it..... it's in my far back room with, most often, only the backup webserver wired to it. I have to be mindful not to tinker with it when I am switched to the webserver wired back there to it.

You already know you just have to try it and see for yourself. If it ws me and wanted a good outcome, I would install the BS build with plans to reset it after the install and reconfig all. That is of course the best to do it anyways. Me being me would throw in the backup main router to do such a thing mainly cause I have lots people depending on it ......and also my webserver. The webserver ain't nothing special but its been around for many years with lots other sites linked back to it ....... gets about a gigabyte per day going from it and I am proud to say you will never see any type avertisement from any of its pages.

I know I get to rambling on but you did ask directly of me

BS or Kong dd-wrt firmware ??? That a really hard question.
Most will tell you Kong is better but that is only because he rarely if ever throws out a bad build. He does a bit of testing on most all routers he supports. AND it really depends on what you are doing and what kinda ISP setup you have. I don't ever have to worry with a stupid ISP modem. I just have the fiber box that will kindly accept, and work, with any type router device that has a RJ45 connection or could just plug computer to it and get WAN IP from router in their local office.

ddw-wrt is a learning experience for everyone, and still many of us old dogs learn something all the time
nickant
DD-WRT User


Joined: 09 Feb 2016
Posts: 151

PostPosted: Sat Jul 13, 2019 10:07    Post subject: Reply with quote
Thank you for your insights, mrjcd.
Sure looks like you have quite the setup over there.
I started off with dd-wrt using Kong on the Linksys wrt1900ac.
Then kong gave up on it and I moved to BS builds.
It was stuck on r31924 for a long time untll BS finally got around to fixing the v1 issue for that router.
I bought an EA8500 cheap locally and have used Kong exclusively on it so far.
If Kong eventally drops the EA8500/dd-wrt I will move to BS builds.
For now r39855M will stay put until a significant issue crops up.
I keep the old WNDR3700v4 handy in case the cat
kills the EA8500 - he likes to sleep on it...

_________________
------------------------------------
Linksys EA8500 DD-WRT r41686 (Gateway + OpenVPN Client)
Linksys WRT1900ACv1 DD-WRT r41686 (AP)
Netgear/Telstra V7610 (spare AP)
Billion BiPAC 7800NXL (spare AP)
Netgear WNDR3700v4 DD-WRT r41369 (spare Gateway + OpenVPN Client)
Photos: https://www.flickr.com/photos/nickant44/albums
eginnc
DD-WRT Novice


Joined: 23 Jul 2017
Posts: 49

PostPosted: Sat Jul 13, 2019 18:16    Post subject: Reply with quote
Router Model: TP-Link ARCHER-C7 v2 (QCA 9558v1 r1.0 720MHz & 9880-BR4A)
Firmware: DD-WRT v3.0-r40276 std (07/12/19)
Kernel: Linux 3.18.140 #46572 Fri Jul 12 04:30:34 CEST 2019 mips
Status: 2.4 and 5 GHz WAPs for Edgerouter X, 2.4 and 5 Guest VAPs on br1, switch for Roku3 streambox and Ooma VOIP.
Reset: No
Issues: None

Router Model: Trendnet TEW824DRU v1.1R (QCA 9558v1 r1.0 720MHz & 9880-BR4A)
Firmware: DD-WRT v3.0-r40276 std (07/12/19)
Kernel: Linux 3.18.140 #46590 Fri Jul 12 04:58:19 CEST 2019 mips
Status: backup router
Reset: No
Issues: None
GUI response time back to normal in this build. Still no Wireguard or WPA3 (Archer C7 V2 has both) Sad

_________________
TP-Link Archer C7v2(US) (dd-wrt r40932)
Linksys EA8500 (OpenWrt 18.06.4)
Edgerouter X (OpenWrt 18.06.4)
CaNsA
DD-WRT User


Joined: 06 Mar 2007
Posts: 70

PostPosted: Sat Jul 13, 2019 20:56    Post subject: Reply with quote
WNDR3700v4
DD-WRT v3.0-r40276 std (07/12/19)
Reset to defaults.
Gateway/AP
Nothing special.

Sporadic reboots.

Unuseable.

_________________
Remember people, it's not hard to link someone to the correct firmware.
mrjcd
DD-WRT Guru


Joined: 31 Jan 2015
Posts: 4862
Location: Texas

PostPosted: Sun Jul 14, 2019 11:53    Post subject: Reply with quote
r40276 up 1 day, 14:40 main router EA8500 tis all good Cool

from laptop on 2.4
mrjcd@Will-Be-Was:~$ speedtest-cli --share
Retrieving speedtest.net configuration...
Testing from Brazos Internet (96.46.208.xxx)...
Retrieving speedtest.net server list...
Selecting best server based on ping...
Hosted by Nortex Communications (Muenster, TX) [130.81 km]: 16.082 ms
Testing download speed................................................................................
Download: 47.29 Mbit/s
Testing upload speed......................................................................................................
Upload: 47.33 Mbit/s
Share results: http://www.speedtest.net/result/8416060091.png
mrjcd@Will-Be-Was:~$
duhceb
DD-WRT Novice


Joined: 11 Apr 2010
Posts: 45

PostPosted: Sun Jul 14, 2019 18:12    Post subject: Reply with quote
My R9000 is okay thus far...I did notice a weird thing. I have static DNS setup with Open DNS to filter content for my family. I used to be able to use CloudFlare on MY devices to bypass, but that doesn’t appear to be the case now. Forced DNS Redirection is NOT on. Any thoughts or is it just this build?
_________________
NETGEAR R9000 Stock FW V1.0.4.12 (ROUTER)
NETGEAR ORBI Stock FW V2.2.1.210 (MESH)
NETGEAR R8500 (Kong Build Usually) (BACKUP)
WRT3200ACM (BS Build Usually) (BACKUP)
mrjcd
DD-WRT Guru


Joined: 31 Jan 2015
Posts: 4862
Location: Texas

PostPosted: Sun Jul 14, 2019 18:21    Post subject: Reply with quote
duhceb wrote:
My R9000 is okay thus far...I did notice a weird thing. I have static DNS setup with Open DNS to filter content for my family. I used to be able to use CloudFlare on MY devices to bypass, but that doesn’t appear to be the case now. Forced DNS Redirection is NOT on. Any thoughts or is it just this build?

Do you have 'No DNS Rebind' enabled in DNSMasq on the 'Services' page.
About all I can think of... I really know nothing about the R9000.
I have 'No DNS Rebind' enabled and 'Forced DNS Redirection' and also using 'Recursive DNS Resolving (Unbound)' so anything connected here has to use that Twisted Evil
duhceb
DD-WRT Novice


Joined: 11 Apr 2010
Posts: 45

PostPosted: Sun Jul 14, 2019 22:53    Post subject: Reply with quote
No such luck. It appears to ignore all the dns settings. I’ve tried several combinations but the router always forces dns despite the configuration of the individual device. Perhaps the removal of DNSCrypt has messed with it.
_________________
NETGEAR R9000 Stock FW V1.0.4.12 (ROUTER)
NETGEAR ORBI Stock FW V2.2.1.210 (MESH)
NETGEAR R8500 (Kong Build Usually) (BACKUP)
WRT3200ACM (BS Build Usually) (BACKUP)
kretex
DD-WRT Novice


Joined: 24 Apr 2019
Posts: 48

PostPosted: Mon Jul 15, 2019 3:38    Post subject: Reply with quote
Router Model: TP-Link TL-MR3420 v.1
Firmware: DD-WRT v3.0-r40276 std (07/12/19) Linux 3.10.108-d8 #14648 Fri Jul 12 03:55:53 CEST 2019 mips
Status: Flash over previous fw using winscp/putty
Reset: No
Errors: WebGUI still buggy

seem Apply Settings on webgui still not working properly Rolling Eyes
Firmware Upgrade webgui still not working properly Rolling Eyes
Restore Configuration webgui still not working properly Rolling Eyes
Goto page 1, 2  Next Display posts from previous:    Page 1 of 2
Post new topic   Reply to topic    DD-WRT Forum Forum Index -> Atheros WiSOC based Hardware All times are GMT

Navigation

 
Jump to:  
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
You cannot attach files in this forum
You cannot download files in this forum