R6250 x2
DD-WRT v3.0-r40270M kongac (07/11/19)
Linux 4.4.185 #670 SMP Thu Jul 11 02:19:39 CEST 2019 armv7l
Previous 39960
GUI install
No reset
Two r6250’s running as 5Ghz APs for roaming devices, AC only, 80Mhz non overlapping channels
All non essential services disabled
All working, no errors
Thank You <Kong> & BS _________________ R7800 x 3 hnyman OpenWRT
Posted: Mon Jul 15, 2019 13:07 Post subject: Re: New Kong's DD-WRT test build 40270M 2019-07-11
Router: Asus RT-AC5300 & RT-AC3200
Firmware: DD-WRT v3.0-r40270M kongac (07/11/19)
Kernel: Linux 4.4.185 #670 SMP Thu Jul 11 02:19:39 CEST 2019 armv7l
Status: Good so far. Uptime 2 hours.
Reset: No
Upgrade: From DD-WRT v3.0-r39960M kongac (06/08/19) via web gui (dd-wrt.v24-K3_AC_ARM_AC5300.bin & dd-wrt.v24-K3_AC_ARM_R8000.bin)
Errors: None so far.
CPU Temperature : CPU 70.8 °C / WL0 42.7 °C / WL1 42.3 °C / WL2 44.0 °C & CPU 68.0 °C / Not available
Working :
Gateway mode & Wireless access point : Multiple DHCP Server
DNSMasq
No DNS Rebind
Query DNS in Strict Order
Usb /jffs, /opt
QoS with FQ_CODEL
wl0, wl1, wl2
Vpn (OpenVPN Client 2.4.7 built on Jul 11 2019), (SoftEther Server, version 4.30 build 9700)
NoCatSplash
Optware-ng 2.0 (ARMv7 EABI softfloat)
Firmware: v3.0-r40270M kongac (07/11/19)
Router/Version: Netgear R7000
Kernel: Linux 4.4.185 #670 SMP Thu Jul 11 02:19:39 CEST 2019 armv7l
Previous: v3.0-r39960M kongac (06/08/19)
Mode/Status: Up and running for 4 days
Reset: Soft boot before and after ddup
Issues/Errors: None
Upgraded via "ddup --flash-latest" over ssh. No 'nvram erase' this time. No unexpected messages in the syslog.
The temperatures are good: CPU 60.2 °C / WL0 46.4 °C / WL1 49.3 °C (The R7000 is wall-mounted.)
Looks like another good build.
Current basic R7000 setup (subject to change of course):
- SFE - On
- STP - On
- Static WAN IP
- LAN DHCP Enabled
- IPv4 only
- Wireless: Regulatory Domain = UNITED_STATES, wl0 Mixed (ch. 6), wl1 NA-Mixed (ch. 161 + 159), AES
- 1 wireless VLAN on wl0
- SNMP disabled, SSH enabled, Telnet disabled
- Firewall enabled, Log Level high
- Syslog: to local server. klogd: disabled.
- USB support - Off
- NO: ttraf, VNC, Zabbix, VPN, Radius, OpenVPN
- NO: UPnP, DMZ, QoS
- NO: Samba, CIFS, JFFS2, miniDLNA, Entware, Optware _________________ Netgear R7000: v3.0-r54248 std (11/29/23)
EdgeRouter-X: EdgeOS v2.0.9-hotfix 7
Firmware Version: DD-WRT v3.0-r40270M kongac (07/11/19)
Kernel Version: Linux 4.4.185 #670 SMP Thu Jul 11 02:19:39 CEST 2019 armv7l
Upgraded: from DD-WRT v3.0-r39960M kongac (06/08/19) via ddup --flash-latest
Reset: No, not this time
Status: Up and running for 48 hours, basic setup as Gateway, static leases, OpenVPN client (on PIA) with Policy Based Routing up and running, 2,4GHz, 5Ghz USB storage NAS and miniDLNA working., OpenVPN server working
1. Kernel module "drbg" should be inserted before VPN connection. Otherwise IKE authentication will fail with "no file found" in the log file. During handshake it asks for kernel modules "crypto-stdrng" and "crypto-stdrng-all" which are aliases for drbg.
Because of read-only /etc, I added it to /jffs/etc/config/loaddrbg.startup. Better to ask Kong to do it at proper place.
2. You need to STOP and START Firewall, otherwise it blocks VPN request (either IPsec, or PPTP). Probably it's a result of wrong startup order of StrongSwan and Firewall.
Only with new firmware (r40270M)
3. I was not able to login to DD-WRT dashboard from Vivaldi with ERR_CERT_REVOKED error.
4. After removing old configs from /jffs and generating a new certificates,
/jffs/etc/ipsec.conf and /jffs/etc/strongswan.conf were not created.
5. With old Firmware VPN tunnel freezed after 60-120s. With the latest Firmware it works for hours. So it is perfectly usable.
Last edited by slavau on Wed Jul 24, 2019 17:58; edited 1 time in total