New Build 40501: BS 08-02-2019-r40501

Post new topic   Reply to topic    DD-WRT Forum Forum Index -> Broadcom SoC based Hardware
Author Message
kernel-panic69
DD-WRT Guru


Joined: 08 May 2018
Posts: 1930
Location: Texas, USA

PostPosted: Fri Aug 02, 2019 19:12    Post subject: New Build 40501: BS 08-02-2019-r40501 Reply with quote
Downloads: (if a link doesn't work, try another)
https://download1.dd-wrt.com/dd-wrtv2/downloads/betas/2019/08-02-2019-r40501/
ftp://ftp.dd-wrt.com/betas/2019/08-02-2019-r40501/
Alternate link: DD-WRT website
Note: to use wget (or curl) for CLI flash (`write {f/w} linux`), change the https to http (or use ftp instead)

Changelogs:
SVN* changelog since last build: 40460
Summary: (deprecated after 29739)
*Github mirror: https://github.com/mirror/dd-wrt/

Notes:
1. SFE accelerated NAT is in 33006+ builds but only in kernel 3.2 and newer
2. 'KRACK' vulnerability fixes were completed in r33678 for Broadcom, including k26 (33655) & k24 (33656); use build 33772 or later.
3. Bridge modes on k4.4 devices may sometimes work in some configurations in certain builds but are not supported by the bcmdhd driver. Use client or repeater instead as WDS doesn't work with Broadcom ARM either (see Issues below).
4. Since 39469, udhcpd was removed and replaced with the already present dnsmasq, and PIE qdisc was added for some builds.
5. Policy-Based Routing with SFE enabled was fixed in r39556: 5986 and 5900
6. k2.4 (broadcom/) builds were fixed in 39715 (broken in 39144 through 39654)
7. SFE update (k3.10+ for BCM) was in the 39927 build.


Issues, observations, and/or workarounds reported:
1. Trendnet 81*DRU models are missing factory-to-flash
2. DNScrypt is mostly only using v2 protocols now, but requires Golang that DD can't use: 6246
3. WDS does not work on Broadcom ARM devices (only MIPS<->MIPS)
4. K2.6 builds are broken since 38253(?) (GUI issues): 6538
5. VAPs not working at boot; workaround startup command:
sleep 10;stopservice nas;stopservice wlconf;startservice wlconf;startservice nas
This appears to be fixed for some routers (different kernels, modes, and radios) since build 39508.
6. UDP forwarding might not work with SFE Enabled: 6668


Important: if any issues are found, please provide log info (GUI syslog, `dmesg`, `cat /var/log/messages`).
Or put into SVN ticket. For firewall issues, also provide "iptables" info (`iptables -L`, `iptables -t nat -L`, & the /tmp/.ipt file).

Template to copy (after "Code:") for posting issues, be sure to include the mode in use (gateway, AP, CB, etc.):
Code:
[b]Router/Version: [/b]
[b]File: [/b]
[b]Kernel: [/b]
[b]Mode: [/b]
[b]Status: [/b]

WARNING: This thread is to report on flashing this experimental test build, providing important info for both developers and users. Always state your hardware model, version, mode (e.g. Repeater) and SPECIFIC build (e.g. 33555_NEWD-2_K3.x_mega-nv64k.bin). Please avoid discussions and create a new thread to discuss specific problems or questions, as this thread is for reporting, not support. Posts may be deleted or moved to keep this thread manageable and useful. If you don't understand the risks or what to flash and how, with a means of recovery if it bricks, do NOT flash this experimental test build.
Sponsor
tinkeruntilitworks
DD-WRT User


Joined: 21 May 2019
Posts: 98

PostPosted: Fri Aug 02, 2019 19:44    Post subject: Reply with quote
Router/Version: Netgear R7000P
Firmware: DD-WRT v3.0-r40501 std (08/02/19)
Kernel: Linux 4.4.186 #589 SMP PREEMPT Fri Aug 2 12:07:51 +04 2019 armv7l
Mode: gateway/ap
Status: operational

07-26-2019-r40439/ brick
07-27-2019-r40443/ missing jffs2
07-29-2019-r40452/ missing jffs2
07-30-2019-r40459/ missing jffs2
08-02-2019-r40501/ missing jffs2



errors
Dec 31 19:00:12 DD-WRT kern.warn kernel: CONSOLE: 000000.000 initvars_srom_pci, SROM CRC Error
Dec 31 19:00:12 DD-WRT kern.warn kernel: CONSOLE: 026738.601 initvars_srom_pci, SROM CRC Error
Dec 31 19:00:12 DD-WRT kern.warn kernel: CONSOLE: 026738.633 initvars_srom_pci, SROM CRC Error
Dec 31 19:00:12 DD-WRT kern.warn kernel: CONSOLE: 026738.666 initvars_srom_pci, SROM CRC Error
Dec 31 19:00:13 DD-WRT daemon.info mstpd[621]: error, CTL_set_cist_bridge_config: Couldn't find bridge with index 10
Dec 31 19:00:13 DD-WRT daemon.info mstpd[621]: error, CTL_set_cist_bridge_config: Couldn't find bridge with index 10


Last edited by tinkeruntilitworks on Sat Aug 03, 2019 13:56; edited 1 time in total
flyzipper
DD-WRT User


Joined: 21 Feb 2016
Posts: 259

PostPosted: Fri Aug 02, 2019 20:15    Post subject: Reply with quote
Router/Version: Netgear R7000
Firmware: DD-WRT v3.0-r40501 std (08/02/19)
Kernel: Linux 4.4.186 #584 SMP PREEMPT Fri Aug 2 11:18:37 +04 2019 armv7l
Previous: r40459
Mode/Status: Gateway / working
Reset: no
Issues/Errors: Working so far (SFE remains disabled because its UDP forwarding issues continue to periodically mess with my Xbox Live gaming experience).

Edit... this build (or my ISP) hasn't been very stable for the last 24hrs. Will try a reset/re-config if it persists.

Uptime: 24min
Temperatures: CPU 69.7 °C / WL0 48.6 °C / WL1 54.6 °C


Last edited by flyzipper on Sun Aug 04, 2019 9:27; edited 1 time in total
Valeriy_tc
DD-WRT Novice


Joined: 03 Sep 2016
Posts: 31
Location: Ukraine

PostPosted: Sat Aug 03, 2019 12:13    Post subject: Reply with quote
Router/Version: Linksys EA6400
Firmware: DD-WRT v3.0-r40501 std (08/02/19)
Kernel: Linux 4.4.186 #584 SMP PREEMPT Fri Aug 2 11:18:37 +04 2019 armv7l
Previous: DD-WRT v3.0-r40400 std (07/20/19)
Mode/Status: Gateway/Router/Port Forwarding
Reset: No
Issues/Errors: None so far.

Uptime: 37 min
Temperatures: CPU 66.9 °C / WL0 51.4 °C / WL1 55.0 °C
wuruxu
DD-WRT Novice


Joined: 17 Jun 2019
Posts: 15

PostPosted: Sat Aug 03, 2019 13:08    Post subject: Reply with quote
Router/Version: Linksys EA6300
Firmware: DD-WRT v3.0-r40501 std (08/02/19)
Kernel: Linux 4.4.186 #584 SMP PREEMPT Fri Aug 2 11:18:37 +04 2019 armv7l
Previous: 07-29-2019-r40452
Mode/Status: Gateway/VAP/WireGuard
Reset: Must, without Reset, system is very unstable
Issues/Errors: workaround is needed for VAP

ERROR when I try to write linux2 MTD device
root@ddwrt:/tmp# mtd -f write linksys-ea6400-webflash.bin linux2
Unlocking linux2 ...
Could not unlock MTD device: linux2
linux2: Not supported
Writing from linksys-ea6400-webflash.bin to linux2 ... [e]Failed to get erase block status

I don't know, the operate to write to linux2 is successful ?
Mile-Lile
DD-WRT Guru


Joined: 24 Feb 2013
Posts: 1449
Location: Belgrade

PostPosted: Sat Aug 03, 2019 16:13    Post subject: Reply with quote
tinkeruntilitworks wrote:
Router/Version: Netgear R7000P
Firmware: DD-WRT v3.0-r40501 std (08/02/19)
Kernel: Linux 4.4.186 #589 SMP PREEMPT Fri Aug 2 12:07:51 +04 2019 armv7l
Mode: gateway/ap
Status: operational

07-26-2019-r40439/ brick
07-27-2019-r40443/ missing jffs2
07-29-2019-r40452/ missing jffs2
07-30-2019-r40459/ missing jffs2
08-02-2019-r40501/ missing jffs2



errors
Dec 31 19:00:12 DD-WRT kern.warn kernel: CONSOLE: 000000.000 initvars_srom_pci, SROM CRC Error
Dec 31 19:00:12 DD-WRT kern.warn kernel: CONSOLE: 026738.601 initvars_srom_pci, SROM CRC Error
Dec 31 19:00:12 DD-WRT kern.warn kernel: CONSOLE: 026738.633 initvars_srom_pci, SROM CRC Error
Dec 31 19:00:12 DD-WRT kern.warn kernel: CONSOLE: 026738.666 initvars_srom_pci, SROM CRC Error
Dec 31 19:00:13 DD-WRT daemon.info mstpd[621]: error, CTL_set_cist_bridge_config: Couldn't find bridge with index 10
Dec 31 19:00:13 DD-WRT daemon.info mstpd[621]: error, CTL_set_cist_bridge_config: Couldn't find bridge with index 10


your device has no real jffs, but ubifs volume which is normally used for plex... this big flash space can be used by dd-wrt but only if BS do some of his tricks... try next public...
tinkeruntilitworks
DD-WRT User


Joined: 21 May 2019
Posts: 98

PostPosted: Sat Aug 03, 2019 16:30    Post subject: Reply with quote
thanks for the explanation. the space was used for bloatware in the factory firmware. it had a disney parental controls. an antivirus. some usb sharing etc.

i was pointing it out because it just recently went missing. it has been in there working fine in previous builds. is it normal for things to come and go?


Last edited by tinkeruntilitworks on Wed Aug 07, 2019 20:56; edited 2 times in total
kernel-panic69
DD-WRT Guru


Joined: 08 May 2018
Posts: 1930
Location: Texas, USA

PostPosted: Sat Aug 03, 2019 16:43    Post subject: Reply with quote
To quote a line from a movie, "...at the whim of a madman..." ... I didn't see any specific commits that would've removed /jffs2 functionality from any specific device, but I can back-track.
tinkeruntilitworks
DD-WRT User


Joined: 21 May 2019
Posts: 98

PostPosted: Sat Aug 03, 2019 16:46    Post subject: Reply with quote
yeah figured

hoping it's just a bug

another thing
are those errors worth posting. i just go through to log searching the word error. the bridge one I know is known and i believe is across the board. the other im unsure.
zensmooth
DD-WRT Novice


Joined: 21 Nov 2018
Posts: 16

PostPosted: Sun Aug 04, 2019 12:19    Post subject: TP-Link Archer C9 unresponsive Reply with quote
Router/Version: TP-Link Archer C9 v2
Firmware: v3.0-r40501 std ( 08/02/19 )
Kernel: Linux 4.4.186 #586 SMP PREEMPT Fri Aug 2 11:39:54 +04 2019 armv7l
Previous: DD-WRT v3.0-r40352 std ( 07/16/2019 )
Mode/Status: Gateway/Router/Samba
Reset: Yes

Issues/Errors: Web-GUI become unresponsive after 30 minutes of use.

However, the router remain functional for a good 1 hour and 30+ mins, before the connections become really slow and eventually unresponsive.

A reset on the Router allows it to come back to life, along with my further observation. The CPU load is gradually rising to 100% till the Web-GUI become unresponsive again.

Another note, since I always do a reset to factory default and configure. The SFE was disabled by default. I'm not sure if this is related or not.

Rolling back to DD-WRT v3.0-r40352 std.
tinkeruntilitworks
DD-WRT User


Joined: 21 May 2019
Posts: 98

PostPosted: Sun Aug 04, 2019 13:53    Post subject: Reply with quote
deleted

Last edited by tinkeruntilitworks on Wed Aug 07, 2019 20:57; edited 1 time in total
kernel-panic69
DD-WRT Guru


Joined: 08 May 2018
Posts: 1930
Location: Texas, USA

PostPosted: Sun Aug 04, 2019 17:24    Post subject: Reply with quote
I'm trying to figure out why some devices are locking up so badly, because my old dinosaur E4200 seems to not have these issues since I quit leaving ttraf daemon enabled and disabled uPnP.
tinkeruntilitworks
DD-WRT User


Joined: 21 May 2019
Posts: 98

PostPosted: Sun Aug 04, 2019 17:53    Post subject: Reply with quote
leaving the traffic counter on causes issues?
kernel-panic69
DD-WRT Guru


Joined: 08 May 2018
Posts: 1930
Location: Texas, USA

PostPosted: Sun Aug 04, 2019 18:21    Post subject: Reply with quote
tinkeruntilitworks wrote:
leaving the traffic counter on causes issues?
I don't think it's ever been completely 'fixed', everything I've ever read said it was a broken piece of junk and caused issues. I don't need it's functionality, anyway.
tinkeruntilitworks
DD-WRT User


Joined: 21 May 2019
Posts: 98

PostPosted: Sun Aug 04, 2019 18:54    Post subject: Reply with quote
thanks
Display posts from previous:    Page 1 of 1
Post new topic   Reply to topic    DD-WRT Forum Forum Index -> Broadcom SoC based Hardware All times are GMT

Navigation

 
Jump to:  
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
You can attach files in this forum
You can download files in this forum