New Build 06-30-2019-r40167 * DONT USE THIS BUILD *

Post new topic   Reply to topic    DD-WRT Forum Forum Index -> Marvell MVEBU based Hardware (WRT1900AC etc.)
Goto page Previous  1, 2, 3  Next
Author Message
joe_lopez
DD-WRT Novice


Joined: 01 Jul 2019
Posts: 2

PostPosted: Mon Jul 01, 2019 18:45    Post subject: Reply with quote
I have the same problem but I have a wrt1200AC. Can you tell me how you unbricked it? TFTP does not work either. Router wired and wireless works but I cannot do anything in the gui.
Sponsor
joe_lopez
DD-WRT Novice


Joined: 01 Jul 2019
Posts: 2

PostPosted: Mon Jul 01, 2019 19:07    Post subject: Got it working! Reply with quote
I was inpatient but the turning it off and on several times instructions that Justanotherbrokenrouter gave worked for me eventually. I was not sure it would on my wrt1200AC. Thanks!
PIZZEDMEOFF
DD-WRT User


Joined: 12 Dec 2017
Posts: 152
Location: FL

PostPosted: Mon Jul 01, 2019 19:37    Post subject: Reply with quote
Glad you got it to go, told you just keep at it, took me a bit to get mine flipped from that as well, Just keep at it people it will flip patitions.....
_________________
Downloads:
ftp site: ftp://ftp.dd-wrt.com/betas/2019
SVN Timeline:
https://svn.dd-wrt.com/timeline
Commands:
Misc: sleep 10;stopservice nas;stopservice wlconf;startservice wlconf;startservice nas
samba: { sleep 30; stopservice samba3; startservice samba3; } &


WRT1900ACv1:

WIFI: 2.4ghz: NG-mixed, 20mhz channel width, channel 6, WPA2-CCMP-128.
WIFI: 5ghz: AC/N mixed, 80mhz channel width, channel 100+6, WPA2-CCMP-128.
Misc Info: Wireless Mode: "Client" WPA2 Personal: "CCMP-128 (AES)", Virtual Wireless AP "2.4 + 5ghz", Static IP's VIA Mac+Host, SFE Enabled, No Rebind, Strict, no-resolv.
T-z3P
DD-WRT Novice


Joined: 18 Nov 2011
Posts: 6

PostPosted: Tue Jul 02, 2019 13:22    Post subject: Reply with quote
Well, I didn't know that the build is broken, so I've updated my WRT32x. Now the router is performing well, but the web interface looks like isn't loading properly.

What are my options now? Should I wait for the next build and try to upgrade?

I've also tried to revert to an older firmware, but nothing happens when I hit the "Upgrade" button.

_________________
Linksys WRT32X - DD-WRT v3.0-r40134
Linksys EA6300 - DD-WRT v3.0-r40167
PIZZEDMEOFF
DD-WRT User


Joined: 12 Dec 2017
Posts: 152
Location: FL

PostPosted: Tue Jul 02, 2019 18:02    Post subject: Reply with quote
Manually switch the router from primary to alternate partition or vice versa [backup] partition:

Power off router with power switch.
Turn power back on and Power LED will light.
As soon as all LEDs turn off (~2s), power off router with power switch
Turn power back on and Power LED will light.
As soon as all LEDs turn off (~2s), power off router with power switch
Turn power back on and Power LED will light.
As soon as all LEDs turn off (~2s), power off router with power switch
Turn power back on and allow router to fully boot.
It should now be booted to the alternate firmware partition

T-z3P wrote:
Well, I didn't know that the build is broken, so I've updated my WRT32x. Now the router is performing well, but the web interface looks like isn't loading properly.

What are my options now? Should I wait for the next build and try to upgrade?

I've also tried to revert to an older firmware, but nothing happens when I hit the "Upgrade" button.

_________________
Downloads:
ftp site: ftp://ftp.dd-wrt.com/betas/2019
SVN Timeline:
https://svn.dd-wrt.com/timeline
Commands:
Misc: sleep 10;stopservice nas;stopservice wlconf;startservice wlconf;startservice nas
samba: { sleep 30; stopservice samba3; startservice samba3; } &


WRT1900ACv1:

WIFI: 2.4ghz: NG-mixed, 20mhz channel width, channel 6, WPA2-CCMP-128.
WIFI: 5ghz: AC/N mixed, 80mhz channel width, channel 100+6, WPA2-CCMP-128.
Misc Info: Wireless Mode: "Client" WPA2 Personal: "CCMP-128 (AES)", Virtual Wireless AP "2.4 + 5ghz", Static IP's VIA Mac+Host, SFE Enabled, No Rebind, Strict, no-resolv.
T-z3P
DD-WRT Novice


Joined: 18 Nov 2011
Posts: 6

PostPosted: Tue Jul 02, 2019 19:09    Post subject: Reply with quote
PIZZEDMEOFF wrote:
Manually switch the router from primary to alternate partition or vice versa [backup] partition:

Power off router with power switch.
Turn power back on and Power LED will light.
As soon as all LEDs turn off (~2s), power off router with power switch
Turn power back on and Power LED will light.
As soon as all LEDs turn off (~2s), power off router with power switch
Turn power back on and Power LED will light.
As soon as all LEDs turn off (~2s), power off router with power switch
Turn power back on and allow router to fully boot.
It should now be booted to the alternate firmware partition


Thank you for the answer, I've already read the solution you provided in a previous post, but I want to keep the main partition intact. That would be my last resort, if nothing else works. I've also forgot to mention that I can access SSH on the affected router. Is there a way to push an older version from terminal?

_________________
Linksys WRT32X - DD-WRT v3.0-r40134
Linksys EA6300 - DD-WRT v3.0-r40167
T-z3P
DD-WRT Novice


Joined: 18 Nov 2011
Posts: 6

PostPosted: Tue Jul 02, 2019 21:31    Post subject: Reply with quote
Ok, so I've managed to return the router into a working state. I will detail the steps below:

1. SSH into router
2. cd /tmp
3. Download firmware with wget ftp://ftp.dd-wrt.com/betas/2019/06-27-2019-r40134/linksys-wrt32x/ddwrt-linksys-wrt32x-webflash.bin
4. Check what partition is in use with ubootenv get boot_part (on the 3rd line it will return 1 or 2) and change it if needed with ubootenv set boot_part 1 or 2 (mine was already set to 1, as the default firmware is still on partition 2)
5. Flash firmware with write ddwrt-linksys-wrt32x-webflash.bin linux (if your partition is set to 2, use linux2)
6. Wait to complete and then reboot

PS: The above instructions were followed on WRT32x. I'm not sure if it will work on other routers.

PS2: If you are not able to SSH into router, you can get a USB to TTL cable and follow the steps in this video https://www.youtube.com/watch?v=PZYXKAkuJ5w

_________________
Linksys WRT32X - DD-WRT v3.0-r40134
Linksys EA6300 - DD-WRT v3.0-r40167
giles02134
DD-WRT User


Joined: 25 Feb 2007
Posts: 117

PostPosted: Wed Jul 03, 2019 17:29    Post subject: Reply with quote
So far, on R40134, I've not experienced any of the issues that others have described with these latest builds. Then again, my setup is very straightforward: no VPN, WiFi on each interface, and a virtual WiFi for guests.

My escape plan, should I need one, is:
    Flash to R36154 that worked quite well (including the automatic reboot), letting it reset.
    After reboot, restore from the settings file I'd previously saved from that release.

I blew away the stock firmware quite some time ago, so I'm okay with overwriting the opposite partition.

Does this all make sense? Thanks!

_________________
Router: Linksys WRT1900ACSv2
Modem: Arris Surfboard SB6141
DD-WRT v3.0-r41218 std (10/1/19)
ISP: RCN
NAS: ReadyNas314
gufus
DD-WRT Guru


Joined: 04 Aug 2012
Posts: 601
Location: behind the screen

PostPosted: Wed Jul 03, 2019 19:37    Post subject: Reply with quote
Be carefull with these builds, u should know how to recover if you want to test these images. Rolling Eyes
_________________
WRT3200ACM openwrt 18.06.4
WRT3200ACM dd-wrt r41517
WRT54GL dd-wrt r21676
PIZZEDMEOFF
DD-WRT User


Joined: 12 Dec 2017
Posts: 152
Location: FL

PostPosted: Thu Jul 04, 2019 0:39    Post subject: Reply with quote
i agree, unless your checking the forums first looking for any mishaps, make sure you can use a usb to ttl serial cable to recover and already have the other necessary tools already in place to recover the firmware.
_________________
Downloads:
ftp site: ftp://ftp.dd-wrt.com/betas/2019
SVN Timeline:
https://svn.dd-wrt.com/timeline
Commands:
Misc: sleep 10;stopservice nas;stopservice wlconf;startservice wlconf;startservice nas
samba: { sleep 30; stopservice samba3; startservice samba3; } &


WRT1900ACv1:

WIFI: 2.4ghz: NG-mixed, 20mhz channel width, channel 6, WPA2-CCMP-128.
WIFI: 5ghz: AC/N mixed, 80mhz channel width, channel 100+6, WPA2-CCMP-128.
Misc Info: Wireless Mode: "Client" WPA2 Personal: "CCMP-128 (AES)", Virtual Wireless AP "2.4 + 5ghz", Static IP's VIA Mac+Host, SFE Enabled, No Rebind, Strict, no-resolv.
giles02134
DD-WRT User


Joined: 25 Feb 2007
Posts: 117

PostPosted: Thu Jul 04, 2019 11:14    Post subject: Reply with quote
I'm sorry...I just couldn't resist.
_________________
Router: Linksys WRT1900ACSv2
Modem: Arris Surfboard SB6141
DD-WRT v3.0-r41218 std (10/1/19)
ISP: RCN
NAS: ReadyNas314
scar1943
DD-WRT User


Joined: 10 Nov 2018
Posts: 195
Location: South Carolina

PostPosted: Thu Jul 04, 2019 16:00    Post subject: Reply with quote
giles02134 wrote:
I'm sorry...I just couldn't resist.


ROFL! Laughing
ellick
DD-WRT User


Joined: 28 Mar 2016
Posts: 192

PostPosted: Fri Jul 05, 2019 16:13    Post subject: Reply with quote
giles02134 wrote:
I'm sorry...I just couldn't resist.


Perfect!

Dr. Frankenstein: [Holds up hand] Ah. Good. Uh... would you mind telling me... whose brain... I did put in?
Igor: And you won't be angry?
Dr. Frankenstein: I will not be angry.
Igor: [Shrugs] Abby...someone.
Dr. Frankenstein: Abby someone? Abby who?
Igor: Abby Normal.
Dr. Frankenstein: [takes a deep breath] Abby Normal?
Igor: I'm almost sure that was the name. [He and Dr. Frankenstein laugh]
Dr. Frankenstein: Are you saying... [Stands] that I put an abnormal brain... [Puts hand on Igor's hump] into a 7 and a half foot long... 54- inch wide... [Grabs Igor by throat] GORILLA?!?!?! [Strangling Igor] IS THAT WHAT YOU'RE TELLING ME!?!
Mojave83
DD-WRT Novice


Joined: 07 Jul 2019
Posts: 3

PostPosted: Sun Jul 07, 2019 6:14    Post subject: Reply with quote
I've been so stupid to install this build without thinking.
Now after 20 tries to start the other partition, I still have no luck.

Should I order the USB TTL cable?
davedarr
DD-WRT Novice


Joined: 05 Jan 2016
Posts: 12

PostPosted: Thu Oct 31, 2019 21:07    Post subject: R40167....I need some review and assistance please!!! Reply with quote
A few months ago I had updated 2 of my WRT1900AC routers with this bad build (R40167). Upon doing some research I found data that walked me thru re-flashing to a baseline linksys build with hope of another re-flash to a good DDWRT build for my routers.

Upon removing the shell to my router, I inserted the the TTL Serial cables to the router as follows

(L>R) Black #1, White #2 & Green #4)



Red- Don't Use
Black-Ground
White-RX
Green-TX

Step 1- I went to https://www.linksys.com/us/support-article?articleNum=148550 to obtain an .img file for flashing my router back to a stock firmware. Upon download, I changed the name and placed it in a newly created FTP folder on the root of the C:drive.



Step 2 – Plugged the TTL USB into Laptop & plugged Cat5 cable into port 1 of router as was as Cat5 cable into laptop NIC card (while router is power off).

Step 3 – Changed laptop IPv4 properties to the following
IP address: 192.168.1.2
Subnet mask: 255.255.255.0
Default Gate: 192.168.1.1



Step 4 – Opened TFTPd application on laptop and modified settings for directory of .img file and set the server interface.



Step 5 – Verified Comm port and set Putty accordingly.
Set speed to 115200 and modified Serial line




Step 6 - Turn on router and hit the space bar on keyboard to stop auto-boot when it prompts in Putty terminal.



Step 7 – Within Putty terminal, type in separately the following command followed by hitting the return key. This will set the IP address of the the client, server, name of the img file and tell Putty to reformat both partitions on the router.

setenv ipaddr 192.168.1.1

setenv serverip 192.168.1.2

setenv firmwareName linksys.img

run update_both_images

this should be the end result



Step 8 – Put iPV4 back to DHCP config



Step 9 – in Putty type the word reset and hit enter. The router will reboot. When it comes back Putty should say something about Linksys.

In my case after multiple attemps to flash, I get a Wrong Image Format for bootm command, ERROR: can’t get kernel image!




Here is a copy of all text within my putty shell. Does anyone see what went wrong with the flash? Also, within the terminal there is a reference to Filename “blk-mamba.128mb.img”. What is that referencing?

setenv ipaddr 192.168.1.1

setenv serverip 192.168.1.2

setenv firmwareName linksys.img

run update_both_images

*******************************
reset


***************************************
egiga0 [PRIME], egiga1
modify Phy Status
Saving Environment to NAND...
Erasing Nand...
Writing to Nand... done
#### auto_recovery:2 ####
auto_recovery_check changes bootcmd: run altnandboot
Hit any key to stop autoboot: 0
Marvell>> setenv ipaddr 192.168.1.1
Marvell>> setenv serverip 192.168.1.2
Marvell>> setenv firmwareName linksys.img
Marvell>> run update_both_images
mvNetaSpeedDuplexSet
Using egiga0 device
TFTP from server 192.168.1.2; our IP address is 192.168.1.1
Filename 'blk-mamba.128mb.img'.
Load address: 0x2000000
Loading: T T T T T T T T T T
Retry count exceeded; starting again

NAND erase: device 0 offset 0xa00000, size 0x4000000
Erasing at 0x49e0000 -- 100% complete.
OK

NAND write: device 0 offset 0xa00000, size 0x1e00000
31457280 bytes written: OK
mvNetaSpeedDuplexSet
Using egiga0 device
TFTP from server 192.168.1.2; our IP address is 192.168.1.1
Filename 'blk-mamba.128mb.img'.
Load address: 0x2000000
Loading: T T T T T T T T T T
Retry count exceeded; starting again

NAND erase: device 0 offset 0x3200000, size 0x4000000
Erasing at 0x71e0000 -- 100% complete.
OK

NAND write: device 0 offset 0x3200000, size 0x1e00000
31457280 bytes written: OK
Marvell>> reset
resetting ...

BootROM 1.20
Booting from NAND flash
Step 1: First phase of PEX-PIPE Configuration
Step 2: Configure the desire PIN_PHY_GEN
Step 3 QSGMII enable
Step 4: Configure SERDES MUXes
Step 5: Activate the RX High Impedance Mode
Step 6: [PEX-Only] PEX-Main configuration (X4 or X1)
Step 6.2: [PEX-Only] PCI Express Link Capabilities
Step 7: [PEX-X4 Only] To create PEX-Link
Steps 7,8,9,10 and 11
Steps 12: [PEX-Only] Last phase of PEX-PIPE ConfigurationSteps 13: Wait 15ms before checking resultsSteps 14: [PEX-Only] In order to configureSteps 15: [PEX-Only] In order to configureSteps 16: [PEX-Only] Training Enablestep 17: max_if= 0x7
step 17: PEX0 pexUnit= 0
** Link is Gen1, check the EP capability
--> 0050
mvPexConfigRead: return addr=0x%x0050
--> 7001
--> 7001
--> A005
--> A005
--> 0010
--> 4C12
Gen2 client!
step 17: PEX1 pexUnit= 0
step 17: PEX2 pexUnit= 0
** Link is Gen1, check the EP capability
--> 0040
mvPexConfigRead: return addr=0x%x0040
--> 5001
--> 5001
--> 7005
--> 7005
--> 0010
--> DC12
Gen2 client!
step 17: PEX3 pexUnit= 0
PEX3 : Detected No Link. Status Reg(0x0004DA64) = 0x00000001
step 17: PEX4 pexUnit= 1
PEX4 : Detected No Link. Status Reg(0x00081A64) = 0x00000001
step 17: PEX5 pexUnit= 1
PEX5 : Detected No Link. Status Reg(0x00085A64) = 0x00000001
step 17: PEX6 pexUnit= 1
PEX6 : Detected No Link. Status Reg(0x00089A64) = 0x00000001
DDR3 Training Sequence - Ver 4.5.DDR3 Training Sequence - Static MC Init
DDR3 Training Sequence - HW Training Procedure
DDR3 Training Sequence - Switching XBAR Window to FastPath Window
BootROM: Image checksum verification PASSED

__ __ _ _
| \/ | __ _ _ ____ _____| | |
| |\/| |/ _` | '__\ \ / / _ \ | |
| | | | (_| | | \ V / __/ | |
|_| |_|\__,_|_| \_/ \___|_|_|
_ _ ____ _
| | | | | __ ) ___ ___ | |_
| | | |___| _ \ / _ \ / _ \| __|
| |_| |___| |_) | (_) | (_) | |_
\___/ |____/ \___/ \___/ \__|
** LOADER **


U-Boot 2011.12 (Feb 06 2014 - 17:14:13) Marvell version: v2011.12 2013_Q1.2

Boot version:v1.3.25

Board: RD-AXP-GP rev 1.0
SoC: MV78230 B0
running 2 CPUs
Custom configuration
CPU: Marvell PJ4B (584) v7 (Rev 2) LE
CPU 0
CPU @ 1200 [MHz]
L2 @ 600 [MHz]
TClock @ 250 [MHz]
DDR @ 600 [MHz]
DDR 32Bit Width, FastPath Memory Access
DDR ECC Disabled
DRAM: 256 MiB

Map: Code: 0x0fea7000:0x0ff5e2d4
BSS: 0x0ffefd80
Stack: 0x0f9a6ef8
Heap: 0x0f9a7000:0x0fea7000

NAND: Spansion 1Gb(ID=F101) 128 MiB
MMC: MRVL_MMC: 0
Bad block table found at page 65472, version 0x01
Bad block table found at page 65408, version 0x01
nand_read_bbt: Bad block at 0x000007ea0000


#### auto_recovery ####
[u_env] get auto_recovery == yes
[u_env] get auto_recovery == yes
[u_env] get boot_part == 2
[u_env] get boot_part_ready == 3
auto_recovery enabled:1, boot_part:2, boot_part_ready:3

[boot_count_read] block:0x140000, size:256KB, records:128
[boot_count_read_record] boot_count:1, next_record:60

[boot_count_write] erase:0, auto_recovery->block_offset:0x140000

Updating boot_count ...
[boot_count_write] offset:0x15E000 , length:2048
done

PEX 0.0(0): Root Complex Interface, Detected Link X1, GEN 2.0
PEX 0.1(1): Root Complex Interface, Detected Link X1, GEN 1.1
PEX 0.2(2): Root Complex Interface, Detected Link X1, GEN 2.0
PEX 0.3(3): Detected No Link.
PEX 1.0(4): Detected No Link.
PEX 1.1(5): Detected No Link.
PEX 1.2(6): Detected No Link.

boot_end Offset: 0x100000
u_env_off Offset: 0x100000
s_env_off Offset: 0x140000
devinfo Offset: 0x900000

===================
total_badCount: 0
boot_badCount: 0
u_env_badCount: 0
s_env_badCount: 0
buff_badCount: 0
===================

FPU initialized to Run Fast Mode.
USB 0: Host Mode
USB 1: Host Mode
USB 2: Device Mode
Modules Detected:
mvEthE6171SwitchBasicInit finished
Net: mvSysNetaInit enter
set port 0 to rgmii enter
set port 1 to rgmii enter
egiga0 [PRIME], egiga1
modify Phy Status
auto_recovery_check changes bootcmd: run altnandboot
Hit any key to stop autoboot: 0

NAND read: device 0 offset 0x3200000, size 0x400000
4194304 bytes read: OK
Wrong Image Format for bootm command
ERROR: can't get kernel image!
Marvell>>
Goto page Previous  1, 2, 3  Next Display posts from previous:    Page 2 of 3
Post new topic   Reply to topic    DD-WRT Forum Forum Index -> Marvell MVEBU based Hardware (WRT1900AC etc.) All times are GMT

Navigation

 
Jump to:  
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
You cannot attach files in this forum
You cannot download files in this forum