***BAD- New Build 40134: BS 06-27-2019-r40134 - BAD***

Post new topic   Reply to topic    DD-WRT Forum Forum Index -> Broadcom SoC based Hardware
Goto page 1, 2  Next
Author Message
kernel-panic69
DD-WRT Guru


Joined: 08 May 2018
Posts: 1852
Location: Texas, USA

PostPosted: Fri Jun 28, 2019 12:43    Post subject: ***BAD- New Build 40134: BS 06-27-2019-r40134 - BAD*** Reply with quote
Another day, another build... Wink Check the changelog to see if anything is relevant to you.


Downloads: (if a link doesn't work, try another)
https://download1.dd-wrt.com/dd-wrtv2/downloads/betas/2019/06-27-2019-r40134/
ftp://ftp.dd-wrt.com/betas/2019/06-27-2019-r40134/
Alternate link: DD-WRT website
Note: to use wget (or curl) for CLI flash (`write {f/w} linux`), change the https to http (or use ftp instead)

Changelogs:
SVN* changelog since last build: 40065
Summary: (deprecated after 29739)
*Github mirror: https://github.com/mirror/dd-wrt/

Notes:
1. SFE accelerated NAT is in 33006+ builds but only in kernel 3.2 and newer
2. 'KRACK' vulnerability fixes were completed in r33678 for Broadcom, including k26 (33655) & k24 (33656); use build 33772 or later.
3. Bridge modes on k4.4 devices may sometimes work in some configurations in certain builds but are not supported by the bcmdhd driver. Use client or repeater instead as WDS doesn't work with Broadcom ARM either (see Issues below).
4. Since 39469, udhcpd was removed and replaced with the already present dnsmasq, and PIE qdisc was added for some builds.
5. Policy-Based Routing with SFE enabled was fixed in r39556: 5986 and 5900
6. k2.4 (broadcom/) builds were fixed in 39715 (broken in 39144 through 39654)
7. SFE update (k3.10+ for BCM) was in the 39927 build.


Issues, observations, and/or workarounds reported:
1. Trendnet 81*DRU models are missing factory-to-flash
2. DNScrypt is mostly only using v2 protocols now, but requires Golang that DD can't use: 6246
3. WDS does not work on Broadcom ARM devices (only MIPS<->MIPS)
4. K2.6 builds are broken since 38253(?); GUI issues: 6538
5. VAPs not working at boot; workaround startup command:
sleep 10;stopservice nas;stopservice wlconf;startservice wlconf;startservice nas
This appears to be fixed for some routers (different kernels, modes, and radios) since build 39508.

Important: if any issues are found, please provide log info (GUI syslog, `dmesg`, `cat /var/log/messages`).
Or put into SVN ticket. For firewall issues, also provide "iptables" info (`iptables -L`, `iptables -t nat -L`, & the /tmp/.ipt file).

Template to copy (after "Code:") for posting issues, be sure to include the mode in use (gateway, AP, CB, etc.):
Code:
[b]Router/Version: [/b]
[b]File: [/b]
[b]Kernel: [/b]
[b]Mode: [/b]
[b]Status: [/b]

WARNING: This thread is to report on flashing this experimental test build, providing important info for both developers and users. Always state your hardware model, version, mode (e.g. Repeater) and SPECIFIC build (e.g. 33555_NEWD-2_K3.x_mega-nv64k.bin). Please avoid discussions and create a new thread to discuss specific problems or questions, as this thread is for reporting, not support. Posts may be deleted or moved to keep this thread manageable and useful. If you don't understand the risks or what to flash and how, with a means of recovery if it bricks, do NOT flash this experimental test build.
Sponsor
theone29
DD-WRT Novice


Joined: 11 Nov 2006
Posts: 8

PostPosted: Fri Jun 28, 2019 16:11    Post subject: Reply with quote
R7000-no reset-so far so good. TY.
mrjcd
DD-WRT Guru


Joined: 31 Jan 2015
Posts: 4693
Location: Texas

PostPosted: Fri Jun 28, 2019 16:43    Post subject: Reply with quote
RT-N12D1
DD-WRT v3.0-r40134 mega (06/27/19)
Linux 3.10.108-d8 #25143 Thu Jun 27 14:01:20 CEST 2019 mips
[dd-wrt.v24-40134_NEWD-2_K3.x_mega.bin]
No reset --- GUI install over r40065
just a WAN disabled WAP ...all worky ok :')
Roger W
DD-WRT Novice


Joined: 23 Apr 2014
Posts: 16

PostPosted: Fri Jun 28, 2019 18:45    Post subject: Reply with quote
Router/Version: Asus RT-AC68U
File: asus_rt-ac68u-firmware.trx
Kernel: Linux 4.4.183 #329 SMP PREEMPT Thu Jun 27 07:22:54 CEST 2019 armv7l
Mode: Router
Status: Working so far, no reset

As someone else noted last week, the prior build didn't boot on this device. This one does, so if you were waiting to see, give it a try.
flyzipper
DD-WRT User


Joined: 21 Feb 2016
Posts: 250

PostPosted: Fri Jun 28, 2019 20:56    Post subject: Reply with quote
Router/Version: Netgear R7000
Firmware: DD-WRT v3.0-r40134 std (06/27/19)
Kernel: Linux 4.4.183 #329 SMP PREEMPT Thu Jun 27 07:22:54 CEST 2019 armv7l
Previous: r40065
Mode/Status: Gateway / working
Reset: no
Issues/Errors: This one was weird for me*, update without reset made both wireless antennas disappear for client use, power reset didn't resolve, had to use the physical reset button and config from scratch. Working now.

*I'll admit I mindlessly updated from 40065 to the erroneously published 38124 before reverting to 40065.

Uptime: 16min
Temperatures: CPU 68.0 °C / WL0 48.0 °C / WL1 54.0 °C


Last edited by flyzipper on Fri Jun 28, 2019 21:36; edited 1 time in total
SinCalChewy
DD-WRT User


Joined: 09 Nov 2014
Posts: 292
Location: Bakersfield, CA

PostPosted: Fri Jun 28, 2019 21:15    Post subject: Reply with quote
Router/Version: 2x Linksys E3000
Firmware: dd-wrt.v24-40134_NEWD-2_K3.x_mega-e3000.bin
Previous: dd-wrt.v24-40065_NEWD-2_K3.x_mega-e3000.bin
Kernel: Linux 3.10.108-d8 #25143 Thu Jun 27 14:01:20 CEST 2019 mips
Mode: Client Bridges
Status: Working

One of my E3000 boxes will "Backup" via the config backup page, and one does not (you click it and nothing happens).

NOTE: Reconfigured that bridge and the backups work fine :)

_________________

Deployed Routers:
Netgear R7000 - 3x Kong's 40270M (Gateway: USB /w Entware, Stubby, DoT & DoH, QoS)
Linksys E3000 - 2x build 40723M (Client Bridges)
Linksys E900 - 1x build 40723M (Work Client)

Spares/Backups/Collection:
Too many to list. I have old routers, bricked routers, weird routers. You name it.
thommy181
DD-WRT Novice


Joined: 16 Mar 2019
Posts: 25
Location: Szczecin, Poland EU

PostPosted: Fri Jun 28, 2019 21:55    Post subject: Netgear WNR3500L v2 Reply with quote
Router/Version: Netgear WNR3500L v2
File: from 27 jun 19
Kernel: 3.10
Mode: Internet gateway and Wi-Fi AP
Status: rather big problem
After update via ssh from version 20 jun to 27 jun I can't boot device correctly. It wasn't ping request, Web GUI access and etc. I try hard reset via button on device case and I must config router again. When I try to change configuration in tab named "Switch config" (previously name: "Networking") and I'm order apply settings operation router crash again and situation was again. Device won't ping request and configuration panel isn't available. Power led on device is green then, but blue led of wifi is off. Then device won't working correctly. So I'm back to older version of dd-wrt system.
In my opinion the newest image of dd-wrt for this Netgear is rather unusable for medium level user who want minutely device configuration.
mbze430
DD-WRT User


Joined: 14 May 2012
Posts: 239

PostPosted: Fri Jun 28, 2019 22:56    Post subject: Reply with quote
Router/Version: ASUS RT-AC3200
File:
Kernel:
Mode: Gateway
Status: unusable
My ASUS RT-AC3200 is completely useless now.

After flashing this firmware, PORT 1 and WAN is completely dead. I flashed back to ASUSWRT original firmware and it works perfectly fine

Things I have tried

1) holding WPS to clear NVRAM
2) 'nvram erase' in both ASUSWRT and DDWRT firmware
3) ''mtd-erase2 nvram' in the ASUSWRT firmware
4) in DDWRT unchecking all port's VLAN setting hit apply, reboot and then going back in via WiFi and reseeting all the port's VLAN
5) Disabling all ports and enabling all ports
6) going back to one previous firmware (it has the same behavior)

This firmware is DEATH!

I am running ASUSWRT original firmware till this is resolved.

_________________
ASUS RT-AC3200 - Deployed Client's site
ASUS RT-AC5200 - Merlin
ASUS RT-AX88U - Merlin
wuruxu
DD-WRT Novice


Joined: 17 Jun 2019
Posts: 15

PostPosted: Sat Jun 29, 2019 7:38    Post subject: Reply with quote
Router/Version: Linksys EA6300
File:
Kernel:
Mode: Gateway
Status: unusable
My Linksys EA6300 is completely useless now.

After flashing this firmware, my linksys cann't boot correctly. so I use tftp to flash Firmware: DD-WRT v3.0-r40065 , all is very well
kernel-panic69
DD-WRT Guru


Joined: 08 May 2018
Posts: 1852
Location: Texas, USA

PostPosted: Sat Jun 29, 2019 15:02    Post subject: Build marked BAD... I presume by one of the moderators Reply with quote
I didn't change the subject line of the OP, so I presume one of the mods marked this build as BAD due to problems, although, the downloads are still on the servers at present.
bkaskar
DD-WRT Novice


Joined: 15 Feb 2019
Posts: 11

PostPosted: Sat Jun 29, 2019 15:07    Post subject: No good for WAP Reply with quote
Router/Version: Board: Asus RT-AC68U
File: asus_rt-ac68u-firmware.trx
Kernel:
Mode: AP with VAP bridged to VLAN on other bridges
Status: Does not work in the

Works fine as basic WAP with WAN port assigned to switch.
wl0 and wl1 Radio connects with WPA2-PSK/AES with different SSIDs
When VLAN config is changed from Setup>VLAN tab (Now called Swit....) and setting is applied connections are lost and system becomes unresponsive. After hard reboot WiFi radios stop showing as well.
At which point you again start with full reset.

Other thoughts - It definitely has a lot of new good features, but unfortunately I will not test the AC5300 build for this revision as it doesn't even get to a stable state where my rest of setup is.
Thank you so much for the effort!
tinkeruntilitworks
DD-WRT User


Joined: 21 May 2019
Posts: 96
Location: northeast us

PostPosted: Sat Jun 29, 2019 15:10    Post subject: Reply with quote
thanks for heads up kernel-panic69

i saw the title and got a bit nervous because i installed it yesterday. seems ok on my router

Router/Version: Netgear R7000P
Firmware: DD-WRT v3.0-r40134 std (06/27/19)
Kernel: Linux 4.4.183 #334 SMP PREEMPT Thu Jun 27 07:56:58 CEST 2019 armv7l
Mode: Gateway AP
Status: seems to be working fine
Reset No. gui upgrade over previous version
kernel-panic69
DD-WRT Guru


Joined: 08 May 2018
Posts: 1852
Location: Texas, USA

PostPosted: Sat Jun 29, 2019 15:14    Post subject: Reply with quote
tinkeruntilitworks wrote:
thanks for heads up kernel-panic69

i saw the title and got a bit nervous because i installed it yesterday. seems ok on my router


I just happened to notice the subject change when I refreshed the page. I opted not to flash this one, because it's short commits that would make it worth the bother to me. Neutral
twindragon6
DD-WRT User


Joined: 29 Jun 2008
Posts: 60

PostPosted: Sat Jun 29, 2019 16:26    Post subject: Netgear Nighthawk R7000 Reply with quote
Router/Version: Netgear R7000
Firmware: DD-WRT v3.0-r40134 std (06/27/19)
Kernel: Linux 4.4.183 #329 SMP PREEMPT Thu Jun 27 07:22:54 CEST 2019 armv7l
Mode: Gateway
Reset: No
Previous: 06-20-2019-r40065
Status: Working, all kinds of logging issues and misc.



LOGS.txt
 Description:
Logs:

Download
 Filename:  LOGS.txt
 Filesize:  4.51 KB
 Downloaded:  112 Time(s)

Wildlion
DD-WRT User


Joined: 24 May 2016
Posts: 442

PostPosted: Sat Jun 29, 2019 16:42    Post subject: Reply with quote
Router: Buffalo WZR-1750DHP
Firmware: buffalo-wzr-1750dhp-webflash.bin (v3.0-r40134 std)
Kernel: Linux 4.4.183 #329 SMP PREEMPT Thu Jun 27 07:22:54 CEST 2019 armv7l
Status: Working
Reset: No
Notes on configuration:

    FTP server
    DNSMasq
    DNSSEC
    USB v3.0
    DHCP reservation

Errors:
[list]
Goto page 1, 2  Next Display posts from previous:    Page 1 of 2
Post new topic   Reply to topic    DD-WRT Forum Forum Index -> Broadcom SoC based Hardware All times are GMT

Navigation

 
Jump to:  
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
You can attach files in this forum
You can download files in this forum