Best builds for the Linksys-WRT3200ACM?

Post new topic   Reply to topic    DD-WRT Forum Forum Index -> Marvell MVEBU based Hardware (WRT1900AC etc.)
Author Message
Justanotherbrokenrouter
DD-WRT User


Joined: 27 Apr 2019
Posts: 71

PostPosted: Sat Jun 15, 2019 17:36    Post subject: Best builds for the Linksys-WRT3200ACM? Reply with quote
Web Flashed W/Chrome.
Linksys WRT3200ACM
DD-WRT v3.0 [Beta] Build; r36247, r37305, or r37582 with other issues, but is a clean VPN (SPEED) build
ath0-5GHz AC/N-Mixed Wide HT40 (40MHz), ath1-2.4GHz NG-mixed Full (20MHz), ath2 2.4/5GHz All Disabled
NordVPN DNS 1, DNS 2
NordVPN Client
NordVPN UDP 140Mbps/12Mbps out of 200/10Mbps ISP service.

r37305
AC/N Mixed
Wide HT40 (40 MHz)
124 - 5620 MHz
144 - 5720 MHz
Upper

NG-Mixed
Full (20 MHz)
10 - 2457 MHz 60%

Issues; Normal reboot time. All functions working properly for use with VPN's

(DD-WRT v3.0 [Beta] Build; r36247, 37305), or r37582 Linksys-WRT3200ACM is the fastest build.

After Open VPN is enabled with UDP protocol speeds with these builds are around 140Mbps down/11-12Mbps up. DD-WRT v3.0 [Beta] Build; 36247, DD-WRT v3.0 [Beta] Build; 37305, or 11-03-2018-r37582 has the fastest internet, but with WiFi error issues at times for all builds newer, or old. The errors start usually after running several speed test back to back, device is further than 15-20', or when (RX) is high. 11-17-2018-r37736 Linksys-WRT3200ACM was the first build to have its Wireless Security options changed. This is when more WPA Algorithms options where added, and speeds went down hill from there. If you have very fast internet then you probably will have no worries installing the newest Beta Builds. Those of us that only can run 200Mbps down, and 10Mbps up, or lower are the ones that suffer. 75-85Mbps, while upload is around 10Mbps after UDP OpenVPN is enabled with newer builds . Still WiFi errors with all new builds especially with Note 8 (Only improving error count in new builds). ISP router IP is still showing up in active clients (IP Address eth0), and this started with build r37582. Unable to keep DNS 3 at default 0.0.0.0 with all builds. DNS 3 should have the ability to default to 0.0.0.0, or be disabled. Would just like to see the speeds of old builds in the new builds so that me, and others could stay with the newest, and greatest that have slower internet. Erase nvram works, but doesn't return flash erased message back in telnet with builds past r37932. Well maybe it works.


Last edited by Justanotherbrokenrouter on Sat Jun 15, 2019 18:10; edited 2 times in total
Sponsor
Display posts from previous:    Page 1 of 1
Post new topic   Reply to topic    DD-WRT Forum Forum Index -> Marvell MVEBU based Hardware (WRT1900AC etc.) All times are GMT

Navigation

 
Jump to:  
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
You cannot attach files in this forum
You cannot download files in this forum