New Build: 08-29-2019-r40854

Post new topic   Reply to topic    DD-WRT Forum Forum Index -> Marvell MVEBU based Hardware (WRT1900AC etc.)
Author Message
DaveI
DD-WRT User


Joined: 06 Jul 2009
Posts: 304

PostPosted: Thu Aug 29, 2019 17:52    Post subject: New Build: 08-29-2019-r40854 Reply with quote
Flashed to PARTITION ONE with Firefox 68.02.

ftp://ftp.dd-wrt.com/betas/2019/08-29-2019-r40854/

https://dd-wrt.com/support/other-downloads/?path=betas%2F2019%2F08-29-2019-r40854%2F

Firmware Version
DD-WRT v3.0-r40854 std (08/29/19)
Kernel Version
Linux 4.9.190 #1255 SMP Thu Aug 29 04:26:50 CEST 2019 armv7l

_________________
WRT1900ACSv2
Sponsor
gufus
DD-WRT Guru


Joined: 04 Aug 2012
Posts: 610
Location: behind the screen

PostPosted: Thu Aug 29, 2019 20:20    Post subject: Reply with quote
---

WDS VHT80 STA VAP in ch 104 and 100 DFS in my county CA work

I don't know how many VAP Channels work in WDS VHT80 STA mode

--
MAC Address60:38:E0:B7:F8:E2
Chipset 88W8964 802.11ac
RadioRadio is On
ModeWDS Station
NetworkAC/N-Mixed
SSIDgypsynet_5g
Channel104 + 106 (5520 MHz VHT80)
Busy Time27063 ms
Active Time1038454 ms
Channel Quality98%
TX Power21 dBm
Rate1300 Mb/s
ACK TimingN/A
Encryption - Interface ath0Enabled, WPA2-PSK
Connected Clients1

Wireless Packet Info
Received (RX)
100%62835 OK, no error
Transmitted (TX)
100%48103 OK, no error

Wireless Nodes
Access Point & Clients
MAC Address Radioname Interface Uptime TX Rate RX Rate Info Signal Noise SNR Signal Quality
00:25:9C:13:34:6B ath0 0:19:21 1300M 1170M VHT80SGI -58 -105 47
84%
B4:6B:FC:3E:75:B5 ath0.1 0:03:36 866M 866M VHT80SGI -58 -105 47
84%

_________________
WRT3200ACM openwrt 18.06.4
WRT3200ACM dd-wrt r40009
WRT54GL dd-wrt r21676
PIZZEDMEOFF
DD-WRT User


Joined: 12 Dec 2017
Posts: 155
Location: FL

PostPosted: Thu Aug 29, 2019 22:36    Post subject: Reply with quote
wireless craps out on this one with me ( the bridge ) backed up to previous build.
_________________
Downloads:
ftp site: ftp://ftp.dd-wrt.com/betas/2019
SVN Timeline:
https://svn.dd-wrt.com/timeline
Commands:
Misc: sleep 10;stopservice nas;stopservice wlconf;startservice wlconf;startservice nas
samba: { sleep 30; stopservice samba3; startservice samba3; } &


WRT1900ACv1:

WIFI: 2.4ghz: NG-mixed, 20mhz channel width, channel 6, WPA2-CCMP-128.
WIFI: 5ghz: AC/N mixed, 80mhz channel width, channel 100+6, WPA2-CCMP-128.
Misc Info: Wireless Mode: "Client" WPA2 Personal: "CCMP-128 (AES)", Virtual Wireless AP "2.4 + 5ghz", Static IP's VIA Mac+Host, SFE Enabled, No Rebind, Strict, no-resolv.
ttowling
DD-WRT User


Joined: 01 Mar 2019
Posts: 109

PostPosted: Fri Aug 30, 2019 8:20    Post subject: Reply with quote
PIZZEDMEOFF wrote:
wireless craps out on this one with me ( the bridge ) backed up to previous build.


I had this problem with the previous build on 1900ACSV2.

r40134 is the de facto stable build.
ellick
DD-WRT User


Joined: 28 Mar 2016
Posts: 241

PostPosted: Fri Aug 30, 2019 13:50    Post subject: Reply with quote
ttowling wrote:


r40134 is the de facto stable build.


Funny how different builds cause problems for different people. r40134 is the build where I started having serious problems. I kept losing the GUI completely after a few hours. The router was still up and I could access the internet, even access it from putty but the GUI wouldn't respond from multiple machines and browsers. I'd have to reboot it to get it back.

The most stable build for me is still r40009

I really like the addition of the Cake, QoS discipline, in these later builds though. I'll be switching to one of them as soon as I'm not affected by bugs.

WRT1900acs v.1
MLandi
DD-WRT User


Joined: 04 Dec 2007
Posts: 170

PostPosted: Fri Aug 30, 2019 14:27    Post subject: Reply with quote
Flashed to partition w/FF68.0.2x64. No issues at all, everything running smoothly.
_________________
Netgear R9000 X10
DD-WRT v3.0-r41686 std (12/10/19)
AP, DNSMasq, Local DNS
CloudFlare DNS
QoS using HFSC w/CAKE
Static Leases & DHCP
2.4GHz: 3 + 7 (2422 MHz HT40)
5GHz: 161 + 155 (5805 MHz VHT80)
Xfinity 1Gbps/35Mbps
ttowling
DD-WRT User


Joined: 01 Mar 2019
Posts: 109

PostPosted: Fri Aug 30, 2019 16:41    Post subject: Reply with quote
[/quote]

Funny how different builds cause problems for different people. r40134 is the build where I started having serious problems. I kept losing the GUI completely after a few hours. The router was still up and I could access the internet, even access it from putty but the GUI wouldn't respond from multiple machines and browsers. I'd have to reboot it to get it back.

I really like the addition of the Cake, QoS discipline, in these later builds though. I'll be switching to one of them as soon as I'm not affected by bugs.

WRT1900acs v.1[/quote]

I wonder if a factory reset would help.. but I really can't be bothered to re enter all the settings and then have to set up all the devices that will stop working around my house.
ellick
DD-WRT User


Joined: 28 Mar 2016
Posts: 241

PostPosted: Fri Aug 30, 2019 17:00    Post subject: Reply with quote
[quote="ttowling"]
Quote:



I wonder if a factory reset would help.. but I really can't be bothered to re enter all the settings and then have to set up all the devices that will stop working around my house.


I actually don't mind doing a factory reset and I do clear the settings when upgrading if I have a problem. just to see if that might fix it. I have to set up basic wireless, a vpn and QoS and that's not that big a deal.

In my case the GUI problem goes away as soon as I revert back to r40009.

I tried the two latest builds and the only bug I see is I have to press apply twice to get my vpn to start. I'm using r40854 right now and will be curious to see if I have the wireless problem you and another reported.
PIZZEDMEOFF
DD-WRT User


Joined: 12 Dec 2017
Posts: 155
Location: FL

PostPosted: Sat Aug 31, 2019 11:29    Post subject: Reply with quote
just for clarification it is only the brige that has issues for me, it will run 15 mins or so then do that 2mbtx thing the rest of the wireless works. so if your not using it as a bridge it could be fine for you.
_________________
Downloads:
ftp site: ftp://ftp.dd-wrt.com/betas/2019
SVN Timeline:
https://svn.dd-wrt.com/timeline
Commands:
Misc: sleep 10;stopservice nas;stopservice wlconf;startservice wlconf;startservice nas
samba: { sleep 30; stopservice samba3; startservice samba3; } &


WRT1900ACv1:

WIFI: 2.4ghz: NG-mixed, 20mhz channel width, channel 6, WPA2-CCMP-128.
WIFI: 5ghz: AC/N mixed, 80mhz channel width, channel 100+6, WPA2-CCMP-128.
Misc Info: Wireless Mode: "Client" WPA2 Personal: "CCMP-128 (AES)", Virtual Wireless AP "2.4 + 5ghz", Static IP's VIA Mac+Host, SFE Enabled, No Rebind, Strict, no-resolv.
ellick
DD-WRT User


Joined: 28 Mar 2016
Posts: 241

PostPosted: Sat Aug 31, 2019 14:58    Post subject: Reply with quote
PIZZEDMEOFF wrote:
just for clarification it is only the brige that has issues for me, it will run 15 mins or so then do that 2mbtx thing the rest of the wireless works. so if your not using it as a bridge it could be fine for you.


Ah, ok. That's good to know. I just run it in standard AP mode and it appears solid. The only problem I have is that having to hit "save" then twice on "apply"to make openvpn start.
Display posts from previous:    Page 1 of 1
Post new topic   Reply to topic    DD-WRT Forum Forum Index -> Marvell MVEBU based Hardware (WRT1900AC etc.) All times are GMT

Navigation

 
Jump to:  
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
You cannot attach files in this forum
You cannot download files in this forum