V24 - There's no USB-version for no_kaid

Post new topic   Reply to topic    DD-WRT Forum Forum Index -> Broadcom SoC based Hardware
Goto page 1, 2, 3, 4  Next
Author Message
frater
DD-WRT Guru


Joined: 07 Jun 2006
Posts: 2777

PostPosted: Mon May 19, 2008 18:58    Post subject: V24 - There's no USB-version for no_kaid Reply with quote
If you only have 4 MB of flash you can't load the mega-version.

I have 2 WL-500G Premiums, but I don't want to load the mege-version on my WDS-config.

Please release a nokaid_usb for the final version...

JP

_________________
Asus RT16N + OTRW
Kingston 4GB USB-disk 128 MB swap + 1.4GB ext3 on /opt + 2 GB ext3 on /mnt
Copperjet 1616 modem in ZipB-config
Asterisk, pixelserv & Pound running on router
Another Asus RT16N as WDS-bridge

DD-WRT v24-sp2 vpn (c) 2010 NewMedia-NET GmbH
Release: 12/16/10 (SVN revision: 15758M)
Sponsor
bkmo
DD-WRT User


Joined: 18 Oct 2007
Posts: 385
Location: Grecia, Costa Rica

PostPosted: Mon May 19, 2008 21:34    Post subject: Re: V24 - There's no USB-version for no_kaid Reply with quote
frater wrote:
If you only have 4 MB of flash you can't load the mega-version.

I have 2 WL-500G Premiums, but I don't want to load the mege-version on my WDS-config.

Please release a nokaid_usb for the final version...

JP


I am hacking one together now using the final nokaid build. It is working on my setup now, but I will have to modify it a bit to fit on a 4 meg router. Give me a couple hours and I will post it.
bkmo
DD-WRT User


Joined: 18 Oct 2007
Posts: 385
Location: Grecia, Costa Rica

PostPosted: Mon May 19, 2008 23:04    Post subject: Reply with quote
Here is a V24 final nokaid USB+ version. The webui for USB is a bit different, it has some additions shown as undefined. I will post a jpeg capture with some explanations of what they are. This was put together from the V24 final I downloaded today, with usb module and scripts to load everything. Tested and working on my router. Automounts to /usb/disc#/part# . Optware and automounting can be selected together. I have uploaded an optware tarball that has samba,ftp, thttpd servers pre configured.
tarball here: http://www.dd-wrt.com/phpBB2/viewtopic.php?t=30678&start=15
Bkmo

Edit: Updated to build 9517 posted 5-20. Added small webui to manage unmounting, rebooting, and stats display.
http://router-ip/user/cgi-bin/managegui.cgi



usbcap.JPG
 Description:
 Filesize:  33.9 KB
 Viewed:  18810 Time(s)

usbcap.JPG



v24finalnokaidusb4m9517.bin
 Description:

Download
 Filename:  v24finalnokaidusb4m9517.bin
 Filesize:  3.57 MB
 Downloaded:  1525 Time(s)



Last edited by bkmo on Tue May 20, 2008 18:36; edited 3 times in total
frater
DD-WRT Guru


Joined: 07 Jun 2006
Posts: 2777

PostPosted: Tue May 20, 2008 6:42    Post subject: Reply with quote
That's nice!

I wrote some scripts to automount the discs and the printer daemon.

Can the scripts/code you are using be found in the forum? Can't your code be incorporated in the "official versions" ?

_________________
Asus RT16N + OTRW
Kingston 4GB USB-disk 128 MB swap + 1.4GB ext3 on /opt + 2 GB ext3 on /mnt
Copperjet 1616 modem in ZipB-config
Asterisk, pixelserv & Pound running on router
Another Asus RT16N as WDS-bridge

DD-WRT v24-sp2 vpn (c) 2010 NewMedia-NET GmbH
Release: 12/16/10 (SVN revision: 15758M)
fosk
DD-WRT Novice


Joined: 07 Jun 2006
Posts: 45
Location: fosk.it/dubbione

PostPosted: Tue May 20, 2008 13:20    Post subject: Reply with quote
VINT usb relase on eko directory: http://www.dd-wrt.com/dd-wrtv2/down.php?path=downloads%2Fothers%2Feko%2FV24-VINT-FINAL/
_________________

ADSL2MUE RouterTech 2.60
WRT54G Tomato 1.21
lots WRTs v23 SP2
lots Foneras v24 SP1
bkmo
DD-WRT User


Joined: 18 Oct 2007
Posts: 385
Location: Grecia, Costa Rica

PostPosted: Tue May 20, 2008 13:28    Post subject: Reply with quote
frater wrote:
That's nice!

I wrote some scripts to automount the discs and the printer daemon.

Can the scripts/code you are using be found in the forum? Can't your code be incorporated in the "official versions" ?

The automount scripts, and printer daemon scripts are already in the firmware I uploaded. They are based on scripts found in some of the wikis. Shinji257 did a nice usb version with serial and acm modem support based on an earlier RC7. He intended to get it incorporated in the official releases. The problem is that he has been busy, and is now quite absent from the forums. That is why I hacked one together with the scripts I did for his build. Too bad about the undefined entries in the webui. This cannot be changed by the firmware mod kit. The services page has to be added in when compiling fom source.
MilanMr1
DD-WRT Novice


Joined: 16 Sep 2007
Posts: 9

PostPosted: Thu May 22, 2008 19:04    Post subject: Reply with quote
I have Asus WL-500g Deluxe and 4 MB of flash.
I have USB print Canon BJC-6500 and VoIP Linksys SPA942.

Is there firmwae for support ethernet VoIP (RJ45) + for USB print together?
Thanks.
bkmo
DD-WRT User


Joined: 18 Oct 2007
Posts: 385
Location: Grecia, Costa Rica

PostPosted: Thu May 22, 2008 20:00    Post subject: Reply with quote
MilanMr1 wrote:
I have Asus WL-500g Deluxe and 4 MB of flash.
I have USB print Canon BJC-6500 and VoIP Linksys SPA942.

Is there firmwae for support ethernet VoIP (RJ45) + for USB print together?
Thanks.

The IP phone should work fine with any v24 firmwares with the proper ports forwared to its ip address. Or did I miss what you were asking?
MilanMr1
DD-WRT Novice


Joined: 16 Sep 2007
Posts: 9

PostPosted: Thu May 22, 2008 21:44    Post subject: Reply with quote
Yes. Thanks.

Last question:
The firmware dd-wrt.v24_voip_generic.bin - support USB print?
If not, use v24finalnokaidusb4m9517.bin.
bkmo
DD-WRT User


Joined: 18 Oct 2007
Posts: 385
Location: Grecia, Costa Rica

PostPosted: Thu May 22, 2008 21:50    Post subject: Reply with quote
MilanMr1 wrote:
Yes. Thanks.

Last question:
The firmware dd-wrt.v24_voip_generic.bin - support USB print?
If not, use v24finalnokaidusb4m9517.bin.

I think only the Mega version has USB support. You will need to use the nokaidusb that I uploaded. If you need the voip for the Milkfish support, then I probably could strip out the Hotspots and add in the USB. That is if the Voip version has not stripped them out already. It all really depends on what I can fit on a 4meg firmware.
MilanMr1
DD-WRT Novice


Joined: 16 Sep 2007
Posts: 9

PostPosted: Thu May 22, 2008 22:17    Post subject: Reply with quote
If you need the voip for the Milkfish support, then I probably could strip out the Hotspots and add in the USB. -> Yes, please. And QoS.
Thanks.
sbddude
DD-WRT Novice


Joined: 13 Nov 2007
Posts: 4

PostPosted: Fri May 23, 2008 5:53    Post subject: Reply with quote
Can someone give step-by-step instructions for enabling USB storage on a WL-520GU?
bkmo
DD-WRT User


Joined: 18 Oct 2007
Posts: 385
Location: Grecia, Costa Rica

PostPosted: Fri May 23, 2008 14:26    Post subject: Reply with quote
MilanMr1 wrote:
If you need the voip for the Milkfish support, then I probably could strip out the Hotspots and add in the USB. -> Yes, please. And QoS.
Thanks.

I looked and it has been pretty well stripped down already. I will see what I can doo about removing some languages and helpfiles to get USB into the Voip version for you.
MilanMr1
DD-WRT Novice


Joined: 16 Sep 2007
Posts: 9

PostPosted: Fri May 23, 2008 18:12    Post subject: :-) Reply with quote
Thanks.


If this is the problem with a lot of size, I do not know how it is the large, so use v24finalnokaidusb4m9517, at least the QoS.
anthonymo
DD-WRT User


Joined: 09 Apr 2008
Posts: 266

PostPosted: Sat May 24, 2008 1:45    Post subject: Reply with quote
http://www.dd-wrt.com/dd-wrtv2/downloads/others/eko/V24_FINAL-NEWD
http://www.dd-wrt.com/dd-wrtv2/downloads/others/eko/V24_FINAL-VINT


Eko has both NEWD and VINT nokaid usb builds
along with a MINI usb build!

_________________
--------------------------------
WRT-54G V2 Running 16403M VINT Eko std-nokaid
WR850G V2 Running v24-Sp1 10011 mini
Ubnt Routerstation running 16785 Std
Cisco Valet (M10)16773M NEWD-2 K2.6 Eko std-nokaid-small
Goto page 1, 2, 3, 4  Next Display posts from previous:    Page 1 of 4
Post new topic   Reply to topic    DD-WRT Forum Forum Index -> Broadcom SoC based Hardware All times are GMT

Navigation

 
Jump to:  
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
You can attach files in this forum
You can download files in this forum