People are creating threads to announce new builds without placing the proper warning at the beginning. I suspect this is being done by people who haven't had to deal with builds that have caused multiple unrecoverable bricks.
Do NOT post a thread announcing a new build without including this warning, only adapted to reflect the proper build number:
This build thread is for reporting successes and problem with loading this experimental test build. This is important info for developers and users. Always state your hardware and SPECIFIC build (e.g. 29000_NEWD-2_K2.6_mega-nv64k.bin). Do not ask questions about your specific router or how to configure it in this thread; create your own thread to discuss any specific problems you have or need resolved. Please also do not respond to such questions. This thread is to report info, not to seek it. Posts that do not add to understanding this build will be deleted. Make sure you know how to flash properly and the risk before using this build. It is important to adhere to these requirements, to keep this thread from becoming impossibly long and useless. If you don't know what build to flash and how to flash properly and have a means of recovery if things should go wrong, do NOT flash this experimental test build.
_________________ Location 1
R7800- DD-WRT v3.0-r53562 (10/03/23) Gateway
WNDR3400v1 DD-WRT v3.0-r35531_mega-nv64k (03/26/18 ) Access Point
WRT160Nv3 DD-WRT ?v3?.0-r35531 mini (03/26/18 ) Access Point
WRT54GSv5 DD-WRT v24-r33555_micro_generic (10/20/17) Repeater
Location 2
R7800- DD-WRT v3.0-r51855 (02/25/23) Gateway
R6300v2- DD-WRT v3.0-r50671 (10-26-22) Access Point
WNDR3700v2 DD-WRT v3.0-r35531 std (03/26/18 ) Access Point
E1200 v2 DD-WRT v3.0-r35531 mega-nv64k (03/26/18 ) Gateway(for trivial reasons)
RBWAPG-5HACT2HND-BE RouterOS-v6.46.4 (2/21/20) Outdoor Access Point
2x RBSXTG-5HPACD RouterOS-v6.46.4 (2/21/20) PTP Bridge 866.6Mbps-1GbpsLAN
Location 3
2x R7000- DD-WRT v3.0-r50671 (10/26/22) Access Points
2x RBWAPG-60AD RouterOS-v6.45.9 (04/30/20) PTP Bridge 2.3Gbps-1GbpsLAN
2x RBSXTsqG-5acD RouterOS-v6.49.7 (10/14/22) PTP Bridge 866.6Mbps-1GbpsLAN Thank You BrainSlayer for ALL that you do & have done, also to "most" everyone here that shares their knowledge
Model: Netgear R7000
Firmware Version DD-WRT v3.0-r39715M kongac (05/09/19)
Kernel VersionLinux 4.4.179 #658 SMP Thu May 9 10:24:44 CEST 2019
Reset: Yes
Works very well in my simple set up. Thanks BS and Kong!
Router: ASUS AC1900(AC68U)
Firmware: DD-WRT v3.0-r39715M kongac (05/09/19)
Kernel: Linux 4.4.179 #658 SMP Thu May 9 10:24:44 CEST 2019 armv7l
Setup Gateway/AP (very basic setup)
Status: Working fine so far
Reset: Yes. nvram erase+reboot before and after ddup --flash-latest
Temperatures CPU 39.1 °C / WL1 41.4 °C
Errors: As far as i can tell nothing new showing up in Klogd
Thank you <Kong> and <BS> _________________ Router: ASUS AC1900(RT-AC68U)
Router: Netgear 6250 x 2
Firmware: DD-WRT v3.0-r39715M kongac (05/09/19)
Setup: AP x 2, 5ghz AC only, 80Mhz non overlapping channels, explicit beamforming (very basic setup, most services disabled)
Status: Working great
Reset: No. GUI install.
Errors: None
Overall A, A bufferbloat score on dslreports Speedtest.
Firmware Version: DD-WRT v3.0-r39715M kongac (05/09/19)
Kernel Version: Linux 4.4.179 #658 SMP Thu May 9 10:24:44 CEST 2019 armv7l
Upgraded: from DD-WRT v3.0-r39575M kongac (04/20/19) via ddup --flash-latest
Reset: No, not this time
Status: Up and running for 8 hours, basic setup as Gateway, static leases, OpenVPN client (on PIA) with Policy Based Routing up and running, 2,4GHz, 5Ghz USB storage NAS and miniDLNA working, OpenVPN server working.
PBR working with standard SFE!!! Speed with SFE is very good
Joined: 16 Nov 2015 Posts: 6437 Location: UK, London, just across the river..
Posted: Mon May 13, 2019 14:36 Post subject:
Router Model Netgear R7000
Firmware Version DD-WRT v3.0-r39715M kongac (05/09/19)
Kernel Version Linux 4.4.179 #658 SMP Thu May 9 10:24:44 CEST 2019 armv7l
update: ddup 39345 > 39715
reset: NO
status: Operational
errors: Nothing bad for my set up...
10x Kong for keeping us alive !!! _________________ Atheros
TP-Link WR740Nv1 ---DD-WRT 55630 WAP
TP-Link WR1043NDv2 -DD-WRT 55723 Gateway/DoT,Forced DNS,Ad-Block,Firewall,x4VLAN,VPN
TP-Link WR1043NDv2 -Gargoyle OS 1.15.x AP,DNS,QoS,Quotas
Qualcomm-Atheros
Netgear XR500 --DD-WRT 55779 Gateway/DoH,Forced DNS,AP Isolation,4VLAN,Ad-Block,Firewall,Vanilla
Netgear R7800 --DD-WRT 55819 Gateway/DoT,AD-Block,Forced DNS,AP&Net Isolation,x3VLAN,Firewall,Vanilla
Netgear R9000 --DD-WRT 55779 Gateway/DoT,AD-Block,AP Isolation,Firewall,Forced DNS,x2VLAN,Vanilla
Broadcom
Netgear R7000 --DD-WRT 55460 Gateway/SmartDNS/DoH,AD-Block,Firewall,Forced DNS,x3VLAN,VPN
NOT USING 5Ghz ANYWHERE
------------------------------------------------------
Stubby DNS over TLS I DNSCrypt v2 by mac913
Posted: Wed May 15, 2019 2:46 Post subject: EA6350 V2
Router/Version: Linksys EA6350 v2
Firmware: DD-WRT v3.0-r39715M kongac (05/09/19)
Kernel: Linux 4.4.179 #658 SMP Thu May 9 10:24:44 CEST 2019 armv7l
Previous: DD-WRT v3.0-r39575M kongac (04/20/19 )
Mode/Status: Gateway : Up and running
Reset: yes, "nvram erase" before and after update
Issues/Errors: None
Upgrade method: Putty into router and perform "nvram erase" then used web GUI to web flash/ upgrade. Then "nvram erase" again after upgrade. Then re-setup manually. So far so good !
Thank you Kong and BS for all the hard work you do. _________________ WRT54GL v1.1 - Flashed
Linksys WRT54G2 v1 - Flashed
EA6350 v2 - Flashed
Router/Version: Netgear R7000
Firmware: v3.0-r39715M kongac (05/09/19)
Kernel: Linux 4.4.179 #658 SMP Thu May 9 10:24:44 CEST 2019 armv7l
Previous: v3.0-r39575M kongac (04/20/19)
Mode/Status: Up and runnig for 3 1/2 days
Reset: Soft boot before and after ddup
Issues/Errors: None
Upgraded via "ddup --flash-latest" over ssh. No 'nvram erase' this time. No unexpected messages in the syslog. Speed tests indicate advertised rates.
The temperatures are good: CPU 56.9 °C / WL0 45.0 °C / WL1 47.8 °C (The R7000 is wall-mounted.)
Current basic R7000 setup (subject to change of course):
- SFE - On
- STP - On
- Static WAN IP
- LAN DHCP Enabled
- IPv4 only
- Wireless: Regulatory Domain = UNITED_STATES, wl0 Mixed (ch. 1), wl1 NA-Mixed (ch. 161 + 159), AES
- 1 wireless VLAN on wl0
- SNMP disabled, SSH enabled, Telnet disabled
- Firewall enabled, Log Level high
- Syslog: to local server. klogd: disabled.
- USB support - Off
- NO: ttraf, VNC, Zabbix, VPN, Radius, OpenVPN
- NO: UPnP, DMZ, QoS
- NO: Samba, CIFS, JFFS2, miniDLNA, Entware, Optware _________________ Netgear R7000: v3.0-r54248 std (11/29/23)
EdgeRouter-X: EdgeOS v2.0.9-hotfix 7
Router/Version: Netgear Ex6200 x 2
Firmware: v3.0-r39715M kongac (05/09/19)
Previous: DD-WRT v3.0-r38580M mini (02/05/19)
Mode/Status: my wifi devices would not authenticate - rolled back
Reset: Soft boot before and after upgrade
Issues/Errors: as above
Upgraded via web gui, no reset
Have 2 VAPS + standard AP on 2.4Ghz and one standard AP on 5GHz, most of my devices would not connect to either EX6200 unit although they have good signal.
Router/Version: Asus RT -AC5300
Firmware: v3.0-r39715M kongac (05/09/19)
Previous:
Mode/Status: Working
Reset: Soft boot before and after upgrade
Issues/Errors: as above
VPN Server
EOIP
1 VAP _________________ Please Fix The Following Bugs:
EOIP Settings not applied automatically after FW upgrade or reboot. http://svn.dd-wrt.com/ticket/4061
The port 80 forwarding bug with out reapplying settings appears to have been fixxed.
2x R7000 here. Newer user so I'm going to post a couple of pain points, you may or may not consider them to be actual errors.
Using 2019-05-09 test build coming from NG firmware->DDWRT->Factory Reset:
* OpenVPN server form takes the "Public Server Cert" field and does dump it into cert.pem, but cert.pem is not referenced in OpenVPN.conf by default and OpenVPN server will fail to start unless "cert /tmp/openvpn/cert.pem" is manually added to the "Additional config" box.
* I think OpenVPN files (certs, etc.) seem to only be updated in filesystem after reboot, router does not recommend reboot when saving if changes were made.
* The OpenVPN config setting "management 127.0.0.1 14" is not automatically added to the OpenVPN.conf file, so the OpenVPN status page in the web UI is dead out of the box. You have to Google and dig up old posts that propose various possible ports to see what the Web UI might be expecting, the expected port is not even listed on the status UI page and probably should be.
* There seems to be no way to turn "Auto-refresh" to Off on the web UI status pages for LAN, WAN, Wireless
* The form to add static IPs for Mac addresses is _really_ bad to use unless you know that if you don't hit Save after adding each row it won't save anything. I thought it was broken for a while.
* DDNS with No-IP only works if you can find a very specific page on their site to get your host ID number and add it after your domain name. I don't know why this is, but if I hadn't found a link on the forum detailing this obscurity, I would never have got it working. I'm not sure how NG can get a valid update without this issue in their UI.
* Default port count was "32768", but the UI says the default should be 4096. As a new user, I can't tell if it went higher because this model has sufficient memory, or it's just wrong and I should lower it.
* There's no way to cancel a command once entered. Entering a command like "top" will make the web UI unusable.
* Server running the web UI died several times while setting up these 2x R7000s. Had to power cycle units, was just setting options and clicking "Save" on various pages.
* Dark style is not the default ;)
Other things:
* Built-in help is so out-of-date vs. actual options on each page that it's almost useless. Ironically, there is a lot of conflicting information on the forum, the wiki(s), the database, so this would be an ideal spot for up-to-date information to exist.
Thanks for the hard work. Uptime is already 1.5 days without any major issues, which is much better than most of NG's latest FWs...
