Router Model:
Status:
Reset:
Errors: _________________ ASUS GT-BE98 PRO Main: Fiber 5gbps up/down
ASUS AXE16000: AI Mesh node
2 X ASUS RT-AX89X: AI Mesh nodes
QNAP QSW-1208-8C 12-Port 10GbE Switch
XS712T ProSafe 12-Port 10GbE Switch
3 X R9000 DD-WRT Mesh
kong supposedly added wnm sleep mode to bs builds, but its still not working on dir-862L.. hostapd dont start.
-bss_transition is still missing
-wifi frame compression still hasnt worked since it was added
-what was the point of adding uapsd to webif if it wasnt fixed to actually WORK? ath9k has no radio fws to deal with, it dont work there either
-ipq806x performance and latency is still a train wreck as always _________________ LATEST FIRMWARE(S)
BrainSlayer wrote:
we just do it since we do not like any restrictions enforced by stupid cocaine snorting managers
EA8500
No reset -- GUI install over r39688
DD-WRT v3.0-r39715 std (05/03/19)
Linux 4.9.172 #300 SMP Fri May 3 00:57:21 CEST 2019 armv7l
---
WNDR3700v4
DD-WRT v3.0-r39715 std (05/03/19)
Linux 3.18.139 #39941 Fri May 3 04:55:49 CEST 2019 mips
No reset -- GUI install over r39654
both these routers are only--most often used as switches / opvn server / samba share
well the EA8500 also has a VLAN on 2 ports... anyways, all I'm using is worky so far.
anyone wondering --- dnsmasq is still ver 2.8.0
###
prolly stick this on main router, EA8500, but imma thinking 'bout time to reset/reconfig it when I do so that'll have to be afterlater sometime.
Router Model TP-Link TL-WR841ND v11
Firmware Version DD-WRT v3.0-r39715 std (05/03/19)
Kernel Version Linux 3.18.139 #39903 Fri May 3 03:51:56 CEST 2019 mips
Update from r39654 via telnet
Working OK as AP, HT40, NG-Mixed, QOS (HTB + FQCodel). Good throughput and bufferbloat.
Reset: no at first, then yes (see below)
Problems:
1. After update and reboot (no reset) wifi came back as open (unprotected). In GUI wireless security tab WPA was selected but no other option was checked/active. I selected WPA2 Personal and then CCMP-128 (AES) and it showed up WPA Shared Key, the one I had before. After save + apply setting it was all right, came back as protected wifi.
2. Still no Virtual Interfaces Add button. I then reset to factory in hope to make a difference but no luck.
Router Model: TP-Link ARCHER-C7 v2 (QCA 9558v1 r1.0 720MHz & 9880-BR4A)
Firmware: DD-WRT v3.0-r39715 std (05/03/19)
Kernel: Linux 3.18.139 #39921 Fri May 3 04:16:43 CEST 2019 mips
Status: 2.4 and 5 GHz WAPs for Edgerouter X, 2.4 Guest VAP, switch for Roku3 streambox and Ooma VOIP.
Reset: No
Issues: None
Router Model: Trendnet TEW824DRU v1.1R (QCA 9558v1 r1.0 720MHz & 9880-BR4A)
Firmware: DD-WRT v3.0-r39715 std (05/03/19)
Kernel: Linux 3.18.139 #39939 Fri May 3 04:45:49 CEST 2019 mips
Status: backup router
Reset: No
Issues: Same SoC, flash and memory size as Archer C7v2, but no WPA3 or Wireguard _________________ Linksys EA8500
Linksys EA6350v3
Edgerouter X
Posted: Fri May 03, 2019 22:02 Post subject: Upgrades
Router/Version: TP-Link WR841ND v8
Firmware: 39715
Previous: 39654
Mode/Status: WDS Station
Reset: No
Issues/Errors: Yes, missing VAP add button, also error in 39654. No WPA3.
Router/Version: D-Link DIR-615 C1
Firmware: 39715
Previous: 39654
Mode/Status: WDS Station
Reset: No
Issues/Errors: Yes, missing VAP add button, also error in 39654. No WPA3. _________________ Before asking a question on the forums, update dd-wrt: Where do I download firmware? I suggest reading it all.
QCA Best WiFi Settings
Some dd-wrt wiki pages are up to date, others are not. PM me if you find an old one.
Atheros:
Netgear R7800 x3 - WDS AP / station, gateway, QoS
TP-Link Archer C7 v2 x2 - WDS Station
TP-Link TL-WDR3600 v1 - WDS Station
TP-Link 841nd v8 - NU
D-Link 615 C1/E3/I1 x 7 - 1 WDS station
D-Link 825 B1 - NU
D-Link 862L A1 x2 - WDS Station
Netgear WNDR3700v2 - NU
UBNT loco M2 x2 - airOS
Broadcom
Linksys EA6400 - Gateway, QoS
Asus N66U - AP
Netgear WNDR3700v3 - not used
MediaTek
UBNT EdgeRouter X - switch
r39715, EA8500 main router
GUI install over r39575M
Reset & Reconfig
29 static leases
local DNS
QOS HTB PIE
ovpn server
samba share ext4 USB flash drive
isolated guest network on ath0.1, ath1.1 & VLAN port 4 via br1
port range forwarding
It all seems to be working ok but when I enabled 'Recursive DNS Resolving (Unbound)' it appeared to break local DNS and also NO DNS for clients on the 5GHz wifi.
Had to get back to router by its IP and disabled unbound. Can't mess with it any more right now... too many here online.
I know unbound ver 1.9.1 worked fine on previous BS build and also Kong's unbound ver 1.9.0 ..... well besides, on both, the local DNS while connected to its ovpn server which has been broken for a year. I'll looky more at it afterlater
###
EDIT: I had to switch QOS to HFSC FQ_CODEL...... the HTB PIE ain't worh a crap with this build on my 50/50 connection
Joined: 03 Jan 2010 Posts: 7568 Location: YWG, Canada
Posted: Sat May 04, 2019 1:30 Post subject:
mrjcd wrote:
but when I enabled 'Recursive DNS Resolving (Unbound)' it appeared to break local DNS
u have that now too? thats what unbound always did and still does to me, is why i cant use it.. apparently its supposed to be some port binding problem with it and dnsmasq & a user posted a easy patch, but devs gave a flat out "no wont fix" without a reason _________________ LATEST FIRMWARE(S)
BrainSlayer wrote:
we just do it since we do not like any restrictions enforced by stupid cocaine snorting managers
this is first time I ever seen unbound break like that
###
EDIT:
oh I see ... with r39715, If enable unbound must do a reboot and then he works just fine ...
...but still NO local DNS thru its ovpn server.
Oh well, that's the main reason why I keep other ovpn servers active on WAPs
Joined: 03 Jan 2010 Posts: 7568 Location: YWG, Canada
Posted: Sat May 04, 2019 17:45 Post subject:
jerrytouille wrote:
tatsuya46 wrote:
for the first time since this k4.x mess, i can actually use hfsc+fq_codel and get my entered download of near 320mbps. shocking..
now if fq_codel's upload would stop being wasteful and get me the 15mbps+ i entered instead of 13.5..
sfe on vs off?
was supposed to be in kong build thread got them mixed up, bs build is still broken.
sfe doesnt work with qos on, does run at all, unless manually started, then its still only working with upload only as usual. at least for me anyway.. _________________ LATEST FIRMWARE(S)
BrainSlayer wrote:
we just do it since we do not like any restrictions enforced by stupid cocaine snorting managers
