atErik DD-WRT Novice
Joined: 25 Apr 2019 Posts: 26
|
Posted: Wed May 01, 2019 11:03 Post subject: |
|
no. DDWRT-menu > Administration > Commands > Diagnostics > Command-Shell > `nvram get lan_ipaddr` > "Run-Commands":
No response box was shown below Command-Shell box with any response.
and i think (though not 100% sure) that br0 now has IP 192.168.10.252 (after i made below changes)
i have tried your iptables command "iptables -t nat -A POSTROUTING -o br0 -j SNAT --to-source 192.168.10.252"
but it has not improved functionalities
- - - - - - - - - - - - - - - - - - - - -
i'm still trying to establish net route for "ath0.1" (192.168.16.x NET) traffic going VIA "ath1" IP/GW or going VIA br0 to ath1, etc and ultimately into the Internet.
please help.
The settings which i posted in my 1st-post/1st-message/OP-1st-message (in 1st-page of this thread), by now i have CHANGED settings further, Below are the current changes i have made now in DDWRT-1 compared to 1st-page(1st-message) :
* changed ath1's fixed-IP from "192.168.10.250" into "192.168.10.252" <-- it is also the IP of the "DDWRT-1-RTR-1", and GW IP is same "192.168.10.254", ath1 is "Unbridged" & NAT-enabled.
* selected the "disable" option for "SSID-2" broadcast under "ath0" section, kept "ath0" in "Bridge" mode.
* currently DDWRT-1 has,
Route (Static)
Rule # | Destination-LAN | Subnet-Mask ..| Gateway ....| Interface .| Metric | NAT
1...| 192.168.16.0 .| 255.255.255.0 .| 192.168.16.1 . | ath0.1 ...| 0 ...| ✅
2...| 192.168.16.0 .| 255.255.255.0 .| 192.168.16.1 . | ath0 ....| 0 ...| ✅
3...| 192.168.16.0 .| 255.255.255.0 .| 192.168.16.1 . | LAN-&-WLAN | 0 ...| ✅
4...| 192.168.16.1 .| 255.255.255.255 | 192.168.10.252 | LAN-&-WLAN | 0 ...| ✅
Routing table:
Code: | Destination .|.Subnet
LAN NET ..|.Mask ......| Gateway ....| Flags | Metric | interface
---------------┼--------------------┼-------------------┼-------┼--------┼-----------
default ...| 0.0.0.0 .....| 192.168.10.254 | UG . | 0 ...| ath1
192.168.10.0 | 255.255.255.0 .| * ....... | U .. | 0 ...| LAN & WLAN
192.168.10.0 | 255.255.255.0 .| * ....... | U .. | 0 ...| ath1
192.168.16.0 | 255.255.255.0 .| 192.168.16.1 .| UG . | 0 ...| ath0.1
192.168.16.0 | 255.255.255.0 .| * ....... | U .. | 0 ...| ath0.1
192.168.16.1 | 255.255.255.255 | 192.168.10.252 | UGH.| 0 ...| LAN & WLAN |
* Current BRIDGE Settings:
Name: br0 , STP : STP , IGMP Snooping : Off , Prio: 32768 , Forward-Delay: 15 , Max-Age: 20 , MTU: 1500 , Root-MAC: "DDWRT-1-ETH0-MAC-ADRS".
* Current Bridging Table:
Bridge-Name: br0 , STP: yes , Interface: ath0 eth0 eth1
Based on above settings, DDWRT-1's functionalities still remained same as 1st-page 1st-message:
SSID-2 devices can get DHCP based IP from 192.168.16.x NET, but they cannot connect with Internet destination/addresses. |
|