This build thread is for reporting successes and problem with loading this experimental test build. This is important info for developers and users. Always state your hardware and SPECIFIC build (e.g. 29000_NEWD-2_K2.6_mega-nv64k.bin). Do not ask questions about your specific router or how to configure it in this thread; create your own thread to discuss any specific problems you have or need resolved. Please also do not respond to such questions. This thread is to report info, not to seek it. Posts that do not add to understanding this build will be deleted. Make sure you know how to flash properly and the risk before using this build. It is important to adhere to these requirements, to keep this thread from becoming impossibly long and useless. If you don't know what build to flash and how to flash properly and have a means of recovery if things should go wrong, do NOT flash this experimental test build.
Joined: 24 Feb 2013 Posts: 1647 Location: Belgrade
Posted: Thu Oct 11, 2018 7:08 Post subject:
Router Model Netgear R6250
Firmware Version DD-WRT v3.0-r37305 std (10/10/1
Kernel Version Linux 4.4.159 #4001 SMP Wed Oct 10 09:28:16 CEST 2018 armv7l
Status: Working great for my needs. Stable and fast 2,4Ghz and 5Ghz (AP mode - WPA2+AES, didn't test VAP or other modes), Unbound, Speedchecker, PPPoE - Gateway mode, MSTP, ntp client, syslog+klog+remote, ssh, QoS)
Reset: No
Errors: None
Thx BS and others
Last edited by Mile-Lile on Thu Oct 11, 2018 7:31; edited 1 time in total
Router/Version: Asus RT-N18U
Firmware: DD-WRT v3.0-r37305 std (10/10/18 )
Previous: r36995
Reset: No
Mode/Status: soft bricked
Issues/Errors: Webinterface reports upgrade was successful, but router never came back up.
Device goes into bootloop and never recovers. Had to revert r36995 via Asus CFE recovery.
Posted: Thu Oct 11, 2018 12:05 Post subject: Re: New BS Build - 10/10/2018 - r37305
New Build - 10/10/2018 - r37305
Router Model: Asus RT-AC87U, Linux 4.4.159 #4008 SMP Wed Oct 10 10:07:36 CEST 2018 armv7l
Status: AP, DD-WRT v3.0-r37305 std (10/10/18 )
Reset: no
Errors: none that I'm aware of
Working well, seems more stable than r37139. OpenVPN/DNSmasq OK. Uptime 2h. 2 new gimmicks in landing-page.
Router Model: Buffalo D1300, Linux 3.10.108-d6 #21208 Wed Oct 10 16:36:57 CEST 2018 mips
Status: RB, DD-WRT v3.0-r37305 giga (10/10/18 )
Reset: no
Errors: none that I'm aware of
Working REALLY well, especially as RB, steady and stable, far better than revious r37139.
Router Model: Buffalo D1300, Linux 3.10.108-d6 #21208 Wed Oct 10 16:36:57 CEST 2018 mips
Status: CB, DD-WRT v3.0-r37305 giga (10/10/18 )
Reset: no
Errors: none that I'm aware of
OK (CB mode was never an issue). Bandwidth of LAN seems too low/wrong, but LAN (eth0) is OK. Did not recheck again with r37139. _________________ 3xBuffalo WLI-H4-D1300
1xBuffalo WZR-D1800H
1xBuffalo WHR-HP-G300N
1xBuffalo WHR-1166D (stock f/w)
1xAsus RT-AC87U
1xAsus RT-AC88U
1xTP710
Router: Netgear R7000
Firmware: DD-WRT v3.0-r37305 std (10/10/2018)
Kernel: Linux 4.4.159 #4001 SMP Wed Oct 10 09:28:16 CEST 2018 armv7l
Status: Working
Reset: No
Previous: 37139
Errors: No
Temperatures : CPU 56.9 °C / WL0 48.8 °C / WL1 51.1 °C
Working very well :
Router mode : DHCP
SFE Enable STP Enable
DNSMasq
Encrypt DNS
Cache DNSSEC data
Validate DNS Replies (DNSSEC)
Local DNS
No DNS Rebind
Query DNS in Strict Order
wl0, wl1
Vpn (OpenVPN Client)
WARNING> this build softbricks ASUS RT-N18U reported by @djwujek in this thread
BS added a ton of disk/usb/raid/fs/tools-related stuff in this build, so everyone should ensure their relevant build isn't too big to fit now. _________________ FOR SALE: E1500@353, 2*E2500, WRT54GLv1.1 & GSv2 @250, 2*WNR1000v3, WGR614v10-mod, F9K1102v3
...and more; PM me for details: most of these are running FreshTomato now, some are OEM and/or modded
Joined: 26 Mar 2013 Posts: 1886 Location: Hung Hom, Hong Kong
Posted: Thu Oct 11, 2018 17:39 Post subject:
rnix wrote:
Router/Version: Asus RT-N18U
Firmware: DD-WRT v3.0-r37305 std (10/10/18 )
Previous: r36995
Reset: No
Mode/Status: soft bricked
Issues/Errors: Webinterface reports upgrade was successful, but router never came back up.
Device goes into bootloop and never recovers. Had to revert r36995 via Asus CFE recovery.
BS Build 37139 is safe and my RT-N18U is using it.
BS Build 37103 is also safe for RT-N18U. _________________ Router: Asus RT-N18U (rev. A1)
Drink, Blink, Stretch! Live long and prosper! May the Force and farces be with you!
Joined: 08 May 2018 Posts: 17394 Location: Texas, USA
Posted: Thu Oct 11, 2018 18:13 Post subject:
jwh7 wrote:
Quote:
WARNING> this build softbricks ASUS RT-N18U reported by @djwujek in this thread
BS added a ton of disk/usb/raid/fs/tools-related stuff in this build, so everyone should ensure their relevant build isn't too big to fit now.
Except for the Broadcom MIPS devices. Same applies to WPA3. There are devices that aren't getting anything 'new', except maybe patches. Bricking is not always an image size issue, either.
Router/Version: Netgear R7000
Firmware: DD-WRT v3.0-r37305 std ( 10/10/18 )
Kernel: Linux 4.4.159 #4001 SMP Wed Oct 10 09:28:16 CEST 2018 armv7l
Previous: r37139
Mode/Status: Gateway / working
Reset: no
Issues/Errors: None so far (command line upgrade because repeated failures via web UI during the last half-dozen upgrades feels bad).
Uptime: 32 minutes
Temperatures: CPU 65.8 °C / WL0 48.7 °C / WL1 50.3 °C
Router/Version: Belkin Play F7D4302
Files: 37305_NEWD-2_K3.x_mega
Kernels: 3.10.108-d6
Mode: AP
Reset: yes
Status: OK
Issues: VLAN now really confused-> Ethernet broken
possible to fix nvram set vlan1ports="3 2 1 0 5" does not work, it caches only the first value -> results in vlan1ports=3;nvram set vlan2ports="4 5" in WebUI correct VLAN 1 lan ports +Vlan2 none ports ,assign vlan0 to br0, choose vlan2 WAN.
strangly Ethernet works for now, wiviz not working on wl1
Router/Version: Netgear 3500Lv1
File: 37305_NEWD-2_K3.x_mega
Kernel: 3.10.108-d6
Mode: AP
Reset: yes
Status: OK
Issues: Ethernet broken,can be fixed by WebUI, on mine Ethernet port numbers wrong (1=4), can be fixed by setting vlan1ports=4 3 2 1 8*, device is recognized as Linksys WRT54G/GL/GS
I'm unsure if my vlan*ports settings are a good idea
Posted: Fri Oct 12, 2018 2:33 Post subject: New BS Build - 10/10/2018 - r37305
kooper2013 wrote:
New Build - 10/10/2018 - r37305
Router Model: Asus RT-AC87U, Linux 4.4.159 #4008 SMP Wed Oct 10 10:07:36 CEST 2018 armv7l
HOw'd you manage to flash this model? The size is almost 1MB larger and the web flash uploader refuses to upload. Did you apply it via the command line on the router?
Posted: Fri Oct 12, 2018 9:55 Post subject: Re: New BS Build - 10/10/2018 - r37305
3boysdad wrote:
kooper2013 wrote:
New Build - 10/10/2018 - r37305
Router Model: Asus RT-AC87U, Linux 4.4.159 #4008 SMP Wed Oct 10 10:07:36 CEST 2018 armv7l
HOw'd you manage to flash this model? The size is almost 1MB larger and the web flash uploader refuses to upload. Did you apply it via the command line on the router?
Yes, image is bigger, flashed with web-if of previous r37139, not cmd.
Which 'web flash uploader'? From stock? Or ASUS tool? I flashed Merlin first (web-if of stock fw), then DD-WRT many moons ago, and again (half a year later) after a DD-WRT flash has failed. _________________ 3xBuffalo WLI-H4-D1300
1xBuffalo WZR-D1800H
1xBuffalo WHR-HP-G300N
1xBuffalo WHR-1166D (stock f/w)
1xAsus RT-AC87U
1xAsus RT-AC88U
1xTP710
Posted: Fri Oct 12, 2018 12:34 Post subject: Re: New BS Build - 10/10/2018 - r37305
[quote="kooper2013"][quote="3boysdad"]
kooper2013 wrote:
Yes, image is bigger, flashed with web-if of previous r37139, not cmd.
Which 'web flash uploader'? From stock? Or ASUS tool? I flashed Merlin first (web-if of stock fw), then DD-WRT many moons ago, and again (half a year later) after a DD-WRT flash has failed.
I have typically used the 'web update' directly from the web gui (Admin -> Firmware Upgrade). The last two version have typically froze this process and, while the router still functioned, caused the management site to go down until a power cycle could occur.
