OpenVPN CLIENT works fine (nordvpn server)
5GHz wpa2 CCMP-128 (AES)working fine 20MHz Mixed
2.4GHz wpa2 CCMP-128 (AES)working fine 20MHz Mixed
NAS via USB Samba also working fine
*** NOTE ***
This version will NOT flash on my Buffalo WZR-HP-AG300H for those interested. Still on v3.0-r38581 std (02/06/19)
Posted: Sat Mar 02, 2019 18:58 Post subject: something wrong again!
I tried to upgrade my WRT1900ACS V2 but after the successful upgrade (I have not seen any error message), the firmware returned to the previous release.
Updated WRT1200AC v1 from r37837 to r39031 with no reset, no issues using Firefox 65.0.2(64 bit) Up-time 2+ hours. Usual OpenVPN client yellows in syslog.
Wired, wireless,OpenVPN client, DNSMasq and VPN passthru (Corp VPN passes thru OpenVPN Client) working as expected with no wired/wireless or OpenVPN drops noticed since update.
Kernel Version Linux 4.9.161 #854 SMP Sat Mar 2 03:14:15 CET 2019 armv7l
OpenVPN dropped reverted to r37837
Last edited by Monza on Sat Mar 02, 2019 21:14; edited 1 time in total
Joined: 30 May 2017 Posts: 582 Location: Rural Manitoba
Posted: Sat Mar 02, 2019 20:31 Post subject: r39031
WEBFLASH with IE11 r38993 -> r39031 WRT3200acm, 1 local & 1 over WiFi.
Had the usual with no Internet, reboot after upgrade solved as always
WRT1900 V1's & WRT1200 V1 had to change partition to 2 (reboot) ,otherwise would not upgrade to partition 2. WEBFLASH with IE11 r38581 -> r39031
All three done over WiFi
So far no apparent problems. ESP devices still won't connect on 3200's without workarounds. _________________ Starlink & DSL -> TPLink TL-R470T+
->
WRT3200acm Master WDS 5GHz 80Mhz CH 100 (+6) r55819
Ath1 2.4Ghz Disabled
99 Static Leases
ExpressVPN
WRT3200acm r55819 WDS Station 5Ghz
Ath1 AP N/G Mixed Channel 11 HT40
WRT1900Ac V1 5Ghz r55819 WDS Station
(Defective, no 2.4Ghz but 5Ghz works great)
WRT1900AC V1 5Ghz AC 80Mhz WDS Station r55819
2.4Ghz AP Ch1 HT20 Mixed
WRT1900ACS SPARE r54914
WRT1900AC SPARE r54914
WRT1900AC V1 5Ghz AC 80Mhz WDS-AP r55819
2.4Ghz AP Ch1 HT20 Mixed
WRT54G DD-WRT v3.0-r37305 micro AP CH 6 Mixed - Not in use
Since it looks like the Factory flash may still be an issue and I already had 38993 installed on Partition 1 I used the DD upgrade trick to do an in-place upgrade on my WRT1900ACSv2...
Factory Linksys on boot_part 2
DD-WRT on boot_part 1
Running on boot_part 1
Run Command: ubootenv set boot_part 2
DO NOT REBOOT
Upgrade to new WEBFLASH - DO NOT RESET...
Successful in-place upgrade from 38993 to r39031.
Firmware Version
DD-WRT v3.0-r39031 std (03/02/19)
Kernel Version
Linux 4.9.161 #854 SMP Sat Mar 2 03:14:15 CET 2019 armv7l _________________ WRT1900ACSv2
I tried to upgrade my WRT1900ACv1 via GUI, but the firmware returned to the previous release (r38581) upon reboot.
I'd rather not swap partitions etc - this was not necessary before and I will wait for BS to resolve this recent issue. _________________ ------------------------------------
Linksys WRT3200ACM DD-WRT r55819 (Gateway)
Linksys EA8500 OpenWrt-23.05.3 (Wired AP)
Netgear WNDR3700v4 DD-WRT r55819 (spare Gateway)
Photos: https://www.flickr.com/photos/nickant44/albums
I Still had to use the Shell method to upgrade on this build. As for the Rest all working well so far.
Oh yeah id like to mention that the 2.4ghz and 5ghz Virtual Access points are also now working in this build and the previous build. _________________ Downloads:
ftp site: ftp://ftp.dd-wrt.com/betas/2021 SVN Timeline:
https://svn.dd-wrt.com/timeline Commands: Misc: sleep 10;stopservice nas;stopservice wlconf;startservice wlconf;startservice nas
samba: { sleep 30; stopservice samba3; startservice samba3; } &
WRT1900ACv1: WIFI: 2.4ghz: NG-mixed, 20mhz channel width, channel follows AP, WPA2-CCMP-128.
WIFI: 5ghz: AC/N mixed, 40mhz channel width, channel 100+upper, WPA2-CCMP-128.
Misc Info: WPA2 Personal: "CCMP-128 (AES)" Static IP's VIA Mac+Host, SFE Enabled, No Rebind, Strict, no-resolv. NOTE: this is now just a wireless access point so to speak but all settings still apply to what ever wireless person connects.
Joined: 17 Feb 2010 Posts: 611 Location: Yorkshire (GOC)
Posted: Sun Mar 03, 2019 8:18 Post subject:
nickant wrote:
I tried to upgrade my WRT1900ACv1 via GUI, but the firmware returned to the previous release (r38581) upon reboot.
I'd rather not swap partitions etc - this was not necessary before and I will wait for BS to resolve this recent issue.
@Nickant
Same thing with my WRT1900AC v1, however, I got round this by simply re-flashing with r38581 first, then flashing r39031 immediately after. All settings retained.
No need to "swap" partitions manually.
My other routers upgraded via Webflash without a hitch. _________________ Linksys WRT32X v1 - r45677
Linksys WRT1900AC v1 - r45677
TP-Link Archer C9 v1 - r45677
Firmware: ftp://ftp.dd-wrt.com/betas/2021/
Posted: Sun Mar 03, 2019 15:14 Post subject: Re: something wrong again!
I tried to upgrade my router again and again but unfortunately there is no hope. My router recalls the previous release of firmware after the reboot.
This release also should be removed on the ftp site!
dyilmaz wrote:
I tried to upgrade my WRT1900ACS V2 but after the successful upgrade (I have not seen any error message), the firmware returned to the previous release.
Yemble - thank you.
I reflashed my WRT1900ACv1 with r38581 and then reflashed with r39031 as you suggested and it worked!
Initially the r38531 reflash looked bad, as it never gave the "successful" message and the 5 min countdown timer kept going.
I had to manually turn off/on the router to get it to come back up with r38531 before flashing r39031. _________________ ------------------------------------
Linksys WRT3200ACM DD-WRT r55819 (Gateway)
Linksys EA8500 OpenWrt-23.05.3 (Wired AP)
Netgear WNDR3700v4 DD-WRT r55819 (spare Gateway)
Photos: https://www.flickr.com/photos/nickant44/albums
