OpenVPN CLIENT works fine (nordvpn server)
5GHz wpa2 CCMP-128 (AES)working fine 20MHz Mixed
2.4GHz wpa2 CCMP-128 (AES)working fine 20MHz Mixed
NAS via USB Samba also working fine
*** Edit 2-13-1019 ***
After less then 24 hours, Average CPU pegs at 100% until I reboot the router once again. Unknown what the cause is.
Last edited by scar1943 on Wed Feb 13, 2019 14:24; edited 1 time in total
OK
Just upgraded to build 38581,reboot: no issue
Set SFE to disable
In PBR field I type the LAN IP adress of my IPAD
--> all traffic except IPAD IP is now NOT going through VPN (in my case VPN PIA), I can check via DNSFROG that my WAN IP adress is my local ISP one and not VPN one
--> my IPAD cannot access internet, the traffic doesn't go through.
--> if I remove the IPAD IP adress from the PBR field, all traffic revert back to be routed through the VPN
Posted: Thu Feb 07, 2019 20:13 Post subject: Re: New Build: r38581 02-6-19
My very first webflash. Upgrade went smooth from r38381 to this version with Safari 12.0.3, except for two issues that already existed with my previous version:
* iPhone cannot use a static IP address. It will only connect to wireless using DHCP, while our MacBooks can have static IP addresses;
* Firewall logs for outgoing and incoming are still empty, although firewall logging and syslog are enabled.
_________________ Linksys WRT3200ACM:
Gateway mode, DNSMasq for DNS and DHCP, OpenVPN client enabled, Firewall enabled, QoS enabled, USB Printer Support enabled (with USB over IP disabled) for printing. WIFI:
* ath0, 5ghz (private), mixed, 80mhz channel width, WPA2 personal, AES;
* ath1.x, 2.4ghz (private and separate guest) both: mixed, 20mhz channel width, WPA2 personal, AES.
Joined: 04 Aug 2018 Posts: 1447 Location: Appalachian mountains, USA
Posted: Sat Feb 09, 2019 0:22 Post subject: Re: New Build: r38581 02-6-19
Cybernaut wrote:
* Firewall logs for outgoing and incoming are still empty, although firewall logging and syslog are enabled.[/list]
My experience with firewall logging is that for it to work you have to enable kernel logging as well. (This goes back many versions... No idea how many. Maybe forever?) _________________ 2x Netgear XR500 and 3x Linksys WRT1900ACSv2 on 53544: VLANs, VAPs, NAS, station mode, OpenVPN client (AirVPN), wireguard server (AirVPN port forward) and clients (AzireVPN, AirVPN, private), 3 DNSCrypt providers via VPN.
Internet speed: 171 Mb/s
LAN speed: 582 Mb/s
WiFi speed (2.4 Ghz): 53 Mb/s (significantly slower, was 141)
WiFi speed (5 Ghz): 36 Mb/s (slower, was 96)
Can ping WiFi printer and see web page (from LAN)
Cannot see 3 of 4 wired PoE cameras from 2.4 GHz WiFi
Can see 4 of 4 wired PoE cameras via OpenVPN
Chromecast working (5GHz)
iPad working (2.4 GHz)
After about 2 to 4 hours:
- 5GHz stopped working ("No Internet", 2.4GHz is fine)
- WiFI printer ping was about 5000ms (instead of 18ms)
WRT1900AC V1. Upgraded was clean; seems to be good. Usually have 2.4Ghz disabled as it doesn't seem to work well, but will try with this build.
Internet speed: 15.11 Mb/s (rated speed, connection is supposed to be ADSL 15/10).
WiFi speed: Never gets past 'preparing' (Samsung Tab S2 running LineageOS 15, Firefox). Same thing happens in desktop Firefox.
Posted: Mon Feb 11, 2019 6:59 Post subject: Re: New Build: r38581 02-6-19
SurprisedItWorks wrote:
My experience with firewall logging is that for it to work you have to enable kernel logging as well. (This goes back many versions... No idea how many. Maybe forever?)
Thanks for the advice. I enabled Klogd. Still, Incoming and Outgoing Logs are empty under Security > Firewall > Log Management. However, I noticed now that firewall logging entries under Status > Syslog.
Is this the normal behaviour? _________________ Linksys WRT3200ACM:
Gateway mode, DNSMasq for DNS and DHCP, OpenVPN client enabled, Firewall enabled, QoS enabled, USB Printer Support enabled (with USB over IP disabled) for printing. WIFI:
* ath0, 5ghz (private), mixed, 80mhz channel width, WPA2 personal, AES;
* ath1.x, 2.4ghz (private and separate guest) both: mixed, 20mhz channel width, WPA2 personal, AES.
Posted: Thu Feb 14, 2019 2:00 Post subject: WRT32X Bugs Report
The bugs had found from version 06-20-2018-r36168 to 02-06-2019-r38581.
06-20-2018-r36168 to 02-06-2019-r38581
1.
VPN connect is used with PPTP Server. The connection time is too long.
2. Client Mode Only
If WRT32X is used with client mode for connection and disabled the http login to the web interface. Only using https accesses to web interface. The webpage will not load unless the user recover to the default setting.
3.
The scheduld reboot time is too long. It needs to waste more than 10 minutes. But the manual reboot or telnet using command for rebooting are no this issues happen.
4.
2.4G Wifi cannot mix with 2.4G and 5G together. It needs to disable the 2.4G Channel.
Channel 11 signal is too weak and always disconnect the devices.
5.
The upgrade process needs to repeat at least two times. If not, some functions cannot use.
Joined: 04 Aug 2018 Posts: 1447 Location: Appalachian mountains, USA
Posted: Fri Feb 15, 2019 22:59 Post subject: Re: New Build: r38581 02-6-19
Cybernaut wrote:
SurprisedItWorks wrote:
My experience with firewall logging is that for it to work you have to enable kernel logging as well. (This goes back many versions... No idea how many. Maybe forever?)
Thanks for the advice. I enabled Klogd. Still, Incoming and Outgoing Logs are empty under Security > Firewall > Log Management. However, I noticed now that firewall logging entries under Status > Syslog.
Is this the normal behaviour?
Certainly that's what I've seen as well. If there's a separate firewall log somewhere, I haven't found it yet. Anyone? _________________ 2x Netgear XR500 and 3x Linksys WRT1900ACSv2 on 53544: VLANs, VAPs, NAS, station mode, OpenVPN client (AirVPN), wireguard server (AirVPN port forward) and clients (AzireVPN, AirVPN, private), 3 DNSCrypt providers via VPN.
Updated my WRT1200ACv2 today using Seamonkey on SPARC Solaris 10. I've seen no problems so far. _________________ Netgear R9000
Netgear R7800 (spare)
Linksys WRT1200ac v2 (spare)
Been watching brainslayers Log and this next release has fixed a ton of problems we have been having. He has been working really hard on it for sure. _________________ Downloads:
ftp site: ftp://ftp.dd-wrt.com/betas/2021 SVN Timeline:
https://svn.dd-wrt.com/timeline Commands: Misc: sleep 10;stopservice nas;stopservice wlconf;startservice wlconf;startservice nas
samba: { sleep 30; stopservice samba3; startservice samba3; } &
WRT1900ACv1: WIFI: 2.4ghz: NG-mixed, 20mhz channel width, channel follows AP, WPA2-CCMP-128.
WIFI: 5ghz: AC/N mixed, 40mhz channel width, channel 100+upper, WPA2-CCMP-128.
Misc Info: WPA2 Personal: "CCMP-128 (AES)" Static IP's VIA Mac+Host, SFE Enabled, No Rebind, Strict, no-resolv. NOTE: this is now just a wireless access point so to speak but all settings still apply to what ever wireless person connects.
