New Build 38535: BS 01-31-2019-r38535

Post new topic   Reply to topic    DD-WRT Forum Forum Index -> Broadcom SoC based Hardware
Author Message
jwh7
DD-WRT Guru


Joined: 25 Oct 2013
Posts: 2371
Location: Indy

PostPosted: Fri Feb 01, 2019 17:27    Post subject: New Build 38535: BS 01-31-2019-r38535 Reply with quote
Downloads: (if one doesn't work, try another)
https://download1.dd-wrt.com/dd-wrtv2/downloads/betas/2019/01-31-2019-r38535/
ftp://ftp.dd-wrt.com/betas/2019/01-31-2019-r38535/
Alternate link: DD-WRT website
Note: to use wget (or curl) for CLI flash (`write {f/w} linux`), change the https to http, or use ftp (curl only)

Changelogs:
SVN* changelog since last build (38507)
Summary: (deprecated after 29739)
*Github mirror: https://github.com/mirror/dd-wrt/

Notes:
1. SFE accelerated NAT is in 33006+ builds but only in kernel 3.10 and newer
2. krack fixes for Broadcom were completed in r33678, including k26 (33655) & k24 (33656); use build 33772 or later.
3. Bridge modes on k4.4 devices may sometimes work in some configurations in certain builds but are not supported by the bcmdhd driver. Use client or repeater instead as WDS doesn't work with Broadcom ARM either (see Issue #4 below).
4. R6400v2 support added in r36811-36818, 36825, and 36826. R6700v3 support added in r36828-36840.

Issues, observations, and/or workarounds reported:
1. (egc) Policy-Based Routing broken if SFE enabled: 5900
quarkysg's PBR+SFE fix: 5986
2. Trendnet 81*DRU models are missing factory-to-flash
3. DNScrypt is mostly only using v2 protocols now, but requires Golang that DD can't use: 6246
4. WDS does not work on ARM devices (only MIPS<->MIPS)
5. VAPs not working at boot (k3.10?); workaround startup command:
sleep 10;stopservice nas;stopservice wlconf;startservice wlconf;startservice nas
6. K2.6 builds are broken since 38253(?); GUI issues: 6538

Important: if any issues are found, please provide log info (GUI syslog, `dmesg`, `cat /var/log/messages`).
Or put into SVN ticket. For firewall issues, also provide "iptables" info (`iptables -L`, `iptables -t nat -L`, & the /tmp/.ipt file).

Template to copy (after "Code:") for posting issues, be sure to include the mode in use (gateway, AP, CB, etc.):
Code:
[b]Router/Version: [/b]
[b]File: [/b]
[b]Kernel: [/b]
[b]Mode: [/b]
[b]Status: [/b]

WARNING: This thread is to report on flashing this experimental test build, providing important info for both developers and users. Always state your hardware model, version, mode (e.g. Repeater) and SPECIFIC build (e.g. 33555_NEWD-2_K3.x_mega-nv64k.bin). Please avoid discussions and create a new thread to discuss specific problems or questions, as this thread is for reporting, not support. Posts may be deleted or moved to keep this thread manageable and useful. If you don't understand the risks or what to flash and how, with a means of recovery if it bricks, do NOT flash this experimental test build.

_________________
# NAT/SFE/CTF: limited speed w/ DD # Repeater issues # DD-WRT info: FAQ, Builds, Types, Modes, Changes, Demo #
x64 OPNsense 19.7.7|FT2019.3: EA6900v1.1@1GHz, F7D8302|DD 41596: WNDR4500v2, WNDR4000@533, R6300v1,
E2500, E1500@353, WRT54*@250: GLv1.1 nsg, GSv6 µ, RT-N66U@663
|OEM: WGR614v10@400 -> WNR1000v3 mod


Last edited by jwh7 on Mon Feb 04, 2019 15:35; edited 3 times in total
Sponsor
jwh7
DD-WRT Guru


Joined: 25 Oct 2013
Posts: 2371
Location: Indy

PostPosted: Fri Feb 01, 2019 18:14    Post subject: Reply with quote
Router/Version: Netgear WNDR4500v2
File: .bin upgrade via ssh, os_version=38535M
Kernel: Linux 3.10.108-d8 (OpenWrt GCC 8.2.0 r7577-d14647dd59) #22749 Thu Jan 31 13:05:30 CET 2019
Mode: 2.4GHz Client to 5GHz AP+VAP
Status: good so far

_________________
# NAT/SFE/CTF: limited speed w/ DD # Repeater issues # DD-WRT info: FAQ, Builds, Types, Modes, Changes, Demo #
x64 OPNsense 19.7.7|FT2019.3: EA6900v1.1@1GHz, F7D8302|DD 41596: WNDR4500v2, WNDR4000@533, R6300v1,
E2500, E1500@353, WRT54*@250: GLv1.1 nsg, GSv6 µ, RT-N66U@663
|OEM: WGR614v10@400 -> WNR1000v3 mod
flyzipper
DD-WRT User


Joined: 21 Feb 2016
Posts: 297

PostPosted: Fri Feb 01, 2019 21:17    Post subject: Reply with quote
Router/Version: Netgear R7000
Firmware: DD-WRT v3.0-r38535 std (01/31/19)
Kernel: Linux 4.4.172 #4555 SMP Thu Jan 31 07:13:14 CET 2019 armv7l
Previous: r38507
Mode/Status: Gateway / working
Reset: no
Issues/Errors: No issues so far (and anecdotally, the WiFi client I usually run speed tests on jumped from mid-300s to mid-500s with this release).

Uptime: 16m
Temperatures: CPU 65.8 °C / WL0 49.0 °C / WL1 52.8 °C
Paris17
DD-WRT Novice


Joined: 29 Jun 2015
Posts: 8

PostPosted: Sat Feb 02, 2019 23:47    Post subject: Reply with quote
Router/Version: TP-Link Archer C9 v2
Kernel: Linux 4.4.172 #4557 SMP Thu Jan 31 07:29:52 CET 2019 armv7l
Mode: Gateway/AP
Uptime: 3 hours
Reset: No
Previous: r38507
Status: Seems to be working, so far so good.
Temperature: CPU 67.5 °C / WL0 47.5 °C / WL1 48.5 °C
SinCalChewy
DD-WRT User


Joined: 09 Nov 2014
Posts: 299
Location: Bakersfield, CA

PostPosted: Sun Feb 03, 2019 1:51    Post subject: Reply with quote
Router/Version: 2x Linksys E3000
Firmware: dd-wrt.v24-38535_NEWD-2_K3.x_mega-e3000.bin
Previous: dd-wrt.v24-38507_NEWD-2_K3.x_mega-e3000.bin
Kernel: Linux 3.10.108-d8 #22765 Thu Jan 31 13:21:48 CET 2019 mips
Mode: Both client bridges with all settings not -required- for a bridge turned off. Basic setup.
Status: Seems really good actually. Speedtests are on par (even more so than the last build), no problems so far. If I find some, I shall report back. :)

Router/Version: Linksys E1200v2
Firmware: dd-wrt.v24-38535_NEWD-2_K3.x_mega-e1200v2.bin
Previous: dd-wrt.v24-38507_NEWD-2_K3.x_mega-e1200v2.bin
Kernel: Linux 3.10.108-d8 #22765 Thu Jan 31 13:21:48 CET 2019 mips
Mode: Repeater for our (rare) guests to use, so they're not on our network. It works, though is hardly used, so I haven't tested it much with this build.
Status: Seems to be working. Lol

Router/Version: Trendnet TEW811DRU
Firmware: DD-WRT v3.0-r38535 mini (01/31/19)
Previous: DD-WRT v3.0-r38507 mini (01/29/19)
Kernel: Linux 4.4.172 #4558 Thu Jan 31 07:34:03 CET 2019 armv7l
Mode: AC-only client bridge, all non-required bridge settings turned off. Basic setup.
Status: Seems to be working just fine. :)

_________________

Deployed Routers:
Netgear R7000 - 3x build 41664M (Gateway: DoT/DoH, CAKE QoS, USB /w Entware)
Linksys E3000 - 2x build 41664M (Client Bridges)

Spares/Backups/Collection:
Too many to list. I have old routers, bricked routers, weird routers. You name it.
smask
DD-WRT Novice


Joined: 28 Jan 2016
Posts: 48
Location: The sofa

PostPosted: Sun Feb 03, 2019 20:05    Post subject: Netgear WNR2000v2 Reply with quote
Router: Netgear WNR2000v2
Firmware: fftp://ftp.dd-wrt.com/betas/2019/01-31-2019-r38535/broadcom_K26/dd-wrt.v24-38535_NEWD-2_K2.6_mini.bin (3 584 000 bytes)
Previous: r31221
Kernel: Linux 2.6.24.111 #6003 Thu Jan 31 00:28:46 CET 2019 mips
Load: C 0.00, 0.00, 0.00 (0%)
Reset: Yep, I had to reset in order to get WiFi working again.
Errors/Issues: Not yet. (Uptime 1h 10min)

_________________
WNDR4300 BS K3.18 r40559 (Main AP)
WNDR3700v3 r40009 (WAP)
--- Spares ---
R7000 BS K4.4 r40750 (Dead ethernet ports)
WNDR4000 BS K3.10 r31899 (Loaned out to tenant who lives in my old home)
WNR2000v2 BS K2.6 r39230 (bricks and giggles)
+ A bunch of WRT54GL:s

I use my routers with pretty basic configuration. Only having WiFi + BT coexist enabled.
I don't have any USB devices connected.
kernel-panic69
DD-WRT Guru


Joined: 08 May 2018
Posts: 2641
Location: Texas, USA

PostPosted: Mon Feb 04, 2019 15:46    Post subject: Cisco Linksys E4200 v1 Reply with quote
Router/Version: Cisco Linksys E4200 v1
File: dd-wrt.v24-38535_NEWD-2_K3.x_mega-e4200.bin
Firmware: DD-WRT v3.0-r38535M mega (01/31/19)
Kernel: Linux 3.10.108-d8 #22765 Thu Jan 31 13:21:48 CET 2019 mips
Previous: DD-WRT v3.0-r38507M mega (01/29/19)
Reset: No
Mode: Gateway/AP
Uptime: 1 day, 23:31
Status: OK
Issues/Errors:

Wired and wireless speed testing, download speed has dropped by almost half, upload has doubled -- but this could always be an ISP issue. Will test via OEM E2500v3 and FreshTomato on another E4200v1 for comparison. Other than that, not much has changed.
egc
DD-WRT Guru


Joined: 18 Mar 2014
Posts: 4353
Location: Netherlands

PostPosted: Tue Feb 05, 2019 11:37    Post subject: Reply with quote
Router Model: Linksys E2000 (converted N320)

Firmware Version: DD-WRT v3.0-r38535M Mega 931/1/2019)
Kernel Version: Linux 3.10.108-d8 #22765 Thu Jan 31 13:21:48 CET 2019 mips

Upgraded: from DD-WRT v3.0-r38060 Mega
Reset: No

Status: Up and running for 24 hours, basic setup as Gateway, static leases, OpenVPN client (on PIA) up and running, VPN download speed 5-6 Mb/s, 2,4GHz and 5 GHz working, OpenVPN server working.

Errors: No, Seems like a good build


Big Thanks to the devs!!

_________________
Routers:Netgear R7800, Netgear R6400v1, Netgear R6400v2, Linksys EA6900 (XvortexCFE), Linksys E2000 (converted WRT320N), WRT54GS v1.
Install guide Linksys EA6900: http://www.dd-wrt.com/phpBB2/viewtopic.php?t=291230
OpenVPN Policy Based Routing guide: https://forum.dd-wrt.com/phpBB2/viewtopic.php?t=321686
Install guide R6400v2:http://forum.dd-wrt.com/phpBB2/viewtopic.php?t=316399
OpenVPN Server Setup:https://forum.dd-wrt.com/phpBB2/viewtopic.php?t=318795
Install guide R7800: https://forum.dd-wrt.com/phpBB2/viewtopic.php?t=320614
Wireguard Setup guide:https://forum.dd-wrt.com/phpBB2/viewtopic.php?p=1183135
Display posts from previous:    Page 1 of 1
Post new topic   Reply to topic    DD-WRT Forum Forum Index -> Broadcom SoC based Hardware All times are GMT

Navigation

 
Jump to:  
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
You can attach files in this forum
You can download files in this forum