TP-Link WDR3600 Starting Kernel...

Post new topic   Reply to topic    DD-WRT Forum Index -> Atheros WiSOC basierende Hardware
Author Message
mash110
DD-WRT Novice


Joined: 30 Jun 2017
Posts: 2

PostPosted: Fri Jun 30, 2017 11:06    Post subject: TP-Link WDR3600 Starting Kernel... Reply with quote
Mein TP-Link WDR3600 v1.1 hängt sich beim starten auf.

Ich habe versucht die Originalfirmware aufzuspielen was leider nicht funktioniert hat.

Ich habe eine TTL Verbindung hergestellt. Um dort steht dann Starting kernel ....

Gesamter code :
Code:

U-Boot 1.1.4 (Sep  9 2013 - 14:28:41)

U-boot DB120


DRAM:  128 MB
id read 0x100000ff
flash size 8MB, sector count = 128
Flash:  8 MB
Using default environment

PCIe Reset OK!!!!!!
In:    serial
Out:   serial
Err:   serial
Net:   ag934x_enet_initialize...
No valid address in Flash. Using fixed address
 wasp  reset mask:c03300
WASP  ----> S17 PHY *
: cfg1 0x7 cfg2 0x7114
eth0: ba:be:fa:ce:08:41
athrs17_reg_init: complete
eth0 up
eth0
dup 1 speed 1000
Using eth0 device
TFTP from server 192.168.0.66; our IP address is 192.168.0.86
Filename 'wdr3600v1_tp_recovery.bin'.
Load address: 0x80060000
Loading: #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         ############################
done
Bytes transferred = 8126464 (7c0000 hex)
original_product_id = 00
 original_product_ver = 00
 recovery_product_id = 36000001
 recovery_product_ver = 01
 auto update firmware: product id verify fail!
Autobooting in 1 seconds
## Booting image at 9f020000 ...
   Uncompressing Kernel Image ... OK

Starting kernel ...



Ich habe gelesen, wenn dort bei:
Code:

original_product_id = 00
 original_product_ver = 00
 recovery_product_id = 36000001
 recovery_product_ver = 01
 auto update firmware: product id verify fail!


Folgendes steht ist irgendwas verkehrt gelaufen.

Wie kann ich das Problem lösen?
Sponsor
mash110
DD-WRT Novice


Joined: 30 Jun 2017
Posts: 2

PostPosted: Sat Jul 01, 2017 11:55    Post subject: Lösung Reply with quote
Hier habe ich eine Lösung gefunden.

http://www.cbs-hilfe.de/index.php/computer/3-tp-link-wdr3600-wdr4300-unbrick-wiederbeleben
ofelija
DD-WRT Novice


Joined: 24 May 2019
Posts: 2

PostPosted: Fri May 24, 2019 19:17    Post subject: Re: TP-Link WDR3600 Starting Kernel... Reply with quote
TP-Link WDR3600 v1.3 hangs
ttl: Starting kernel ....

code :
Code:



U-Boot 1.1.4 (Jan 29 2013 - 16:09:44)

U-boot DB120


DRAM:  128 MB
id read 0x100000ff
flash size 8MB, sector count = 128
Flash:  8 MB
Using default environment

PCIe Reset OK!!!!!!
In:    serial
Out:   serial
Err:   serial
Net:   ag934x_enet_initialize...
No valid address in Flash. Using fixed address
 wasp  reset mask:c03300
WASP  ----> S17 PHY *
: cfg1 0x7 cfg2 0x7114
eth0: ba:be:fa:ce:08:41
athrs17_reg_init: complete
eth0 up
eth0
Autobooting in 1 seconds
## Booting image at 9f020000 ...
   Uncompressing Kernel Image ... OK

Starting kernel ...

ofelija
DD-WRT Novice


Joined: 24 May 2019
Posts: 2

PostPosted: Fri May 24, 2019 19:20    Post subject: Reply with quote
How to stop hanging system at booting kernel ... , the router do nothing after that, how fix this?
Display posts from previous:    Page 1 of 1
Post new topic   Reply to topic    DD-WRT Forum Index -> Atheros WiSOC basierende Hardware All times are GMT

Navigation

 
Jump to:  
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
You cannot attach files in this forum
You cannot download files in this forum