Posted: Sat Dec 18, 2021 14:30 Post subject: New Build - 12/18/2021 - r47874
Welcome to Atheros r47874 beta release thread for reporting, feedback to developers and community benefit.
Please do not flash builds until installation is understood, risks involved and device specificrecovery methods.
Avoid discussions, create threads for questions, general problems or use search; this thread is not for support.
Please list router model & revision, operating & wireless mode(s) and exact filename/firmware image flashed.
Issues, observations, and/or workarounds reported:
• WebUI: Clear history or use a portable. Temporary cache bypass: Ctrl+F5, Cmd+Shift+R or new private window/incognito.
• Please report findings with steps needed to reproduce, configuration, clients, output, logs and important information below!
Important:
• For issues provide applicable info: 'dmesg' 'cat /tmp/var/log/messages', syslog klog, serial, strace, tcpdump, wireshark etc.
• Any firewall NAT or WAN issues, show output: 'iptables -vnL' 'iptables -t nat -vnL' 'iptables -t mangle -vnL' and /tmp/.ipt file.
• Gremlins: reset & configure manually, not restore a backup. Reboot. Search Trac & discuss in forum before opening tickets.
• Please include operating & wireless modes (e.g. Gateway, Router, AP, CB, WDS, Mesh) & relevant configuration information.
Update method: SSH / CLI
Router/Version: Netgear R9000 Nighthawk X10
File/Kernel: DD-WRT v3.0-r47874 std (12/18/21)
Previous/Reset: DD-WRT v3.0-r47853 std (12/16/21) / No
Mode/Status: Gateway / Working Normally
Issues/Errors: Although the build did load the leases file on reboot, I had to uncheck Use JFFS2 for client lease DB, Apply, re-check and Apply, to get leases to start updating to /jffs.
Note that I did not have to erase /tmp/dnsmasq.leases to get /jffs to start updating.
Linksys EA8500 ...main gateway
DD-WRT v3.0-r47874 std (12/18/21)
Linux 4.9.292 #605 SMP Fri Dec 17 21:11:23 +07 2021 armv7l
GUI install over r47865
Has NOT been reset in long long time.
37 staic DHCP leases --- some for main net & some for br1
VANILLA FW for both raios
wlan0.1 + wlan1.1 + 1 wired port as VLAN all via isolated br1
main net uses unbound --- all on br1 use 9.9.9.9
port range forwarding
32GB ext4 used as samba share
OVPN server
HFSC - CAKE
forgot to mention I use local DNS since forever
she is worky very well
#
Netgear WNDR3700 V4
DD-WRT v3.0-r47874 std (12/18/21)
Linux 3.18.140-d6 #132105 Sat Dec 18 17:18:44 +07 2021 mips
GUI install over r47865
used as switch & sometime use its radios -- setup same as a WAP
all good
Joined: 16 Nov 2015 Posts: 6410 Location: UK, London, just across the river..
Posted: Sat Dec 18, 2021 16:35 Post subject:
Router Model TP-Link WR1043ND V2
Firmware Version DD-WRT v3.0-r47874 std (12/18/21)
Kernel Version Linux 3.18.140-d6 #132077 Sat Dec 18 16:25:04 +07 2021 mips
update: CLI r47853 > r47874
reset: NO
mode: Gateway
status: Operational 1h+
errors: is this normal...or i haven't noticed it before...my WAN lease time is the same as the local DHCP lease time...
Basic Setup>Network Address Server Settings (DHCP)>Client Lease Expiration=360
at status WAN it shows 6h too...
WAN Remaining Lease Time 0 days 05:46:46
as well at
Services>DHCP Server>Used Domain LAN & WLAN _________________ Atheros
TP-Link WR740Nv1 ---DD-WRT 55179 WAP
TP-Link WR1043NDv2 -DD-WRT 55303 Gateway/DoT,Forced DNS,Ad-Block,Firewall,x4VLAN,VPN
TP-Link WR1043NDv2 -Gargoyle OS 1.15.x AP,DNS,QoS,Quotas
Qualcomm-Atheros
Netgear XR500 --DD-WRT 55460 Gateway/DoH,Forced DNS,AP Isolation,4VLAN,Ad-Block,Firewall,Vanilla
Netgear R7800 --DD-WRT 55460 Gateway/DoT,AD-Block,Forced DNS,AP&Net Isolation,x3VLAN,Firewall,Vanilla
Netgear R9000 --DD-WRT 55363 Gateway/DoT,AD-Block,AP Isolation,Firewall,Forced DNS,x2VLAN,Vanilla
Broadcom
Netgear R7000 --DD-WRT 55460 Gateway/SmartDNS/DoH,AD-Block,Firewall,Forced DNS,x3VLAN,VPN
NOT USING 5Ghz ANYWHERE
------------------------------------------------------
Stubby DNS over TLS I DNSCrypt v2 by mac913
Router: TL-WDR3600 v1
Firmware: tl-wdr3600_us-webflash.bin (v3.0-r47874 std)
Kernel: Linux 3.10.108-d11 #96888 Sat Dec 18 14:45:40 +07 2021 mips
Status: working
Reset: No
Notes on configuration:
Client
Errors:
1. 5Ghz wireless light is not on (2.4Ghz light works)
Router: DIR-825 rev B1
Firmware: dir825-firmware.bin (v3.0-r47874 std)
Kernel: Linux 3.10.108-d11 #96886 Sat Dec 18 14:29:24 +07 2021 mips
Status: Working
Reset: None
Notes on configuration: Used for Wifi Lab (no internet)
Errors:
None
Router: Archer-A7 v5
Firmware: tplink_archer-a7-v5.bin (v3.0-r47874 std)
Kernel: Linux 3.18.140-d6 #132089 Sat Dec 18 16:46:33 +07 2021 mips
Status: Working
Reset: None
Notes on configuration:
DNSMasq
Virtual wireless with bridging x2
multiple DHCP server
I've just noticed something different about latest builds vs older ones. On the Security page, do all radio buttons depend on Firewall being enabled or disabled? If yes, why are they even there, but in no, then something's changed. With firewall disabled, if I check, let's say, Filter Multicast and click Save, the radio button resets to unchecked. Some builds ago it was not behaving like that, the states were still checked.
Joined: 08 May 2018 Posts: 14126 Location: Texas, USA
Posted: Sat Dec 18, 2021 22:44 Post subject:
AsX wrote:
I've just noticed something different about latest builds vs older ones. On the Security page, do all radio buttons depend on Firewall being enabled or disabled? If yes, why are they even there, but in no, then something's changed. With firewall disabled, if I check, let's say, Filter Multicast and click Save, the radio button resets to unchecked. Some builds ago it was not behaving like that, the states were still checked.
I have noticed this, too, and I haven't found a reason yet. But with all of the webUI improvements and changes going on, there is always a possibility for error. Has anyone tested that shiny new feature to disable webUI access from wireless? _________________ "Life is but a fleeting moment, a vapor that vanishes quickly; All is vanity"
Contribute To DD-WRT Pogo - A minimal level of ability is expected and needed... DD-WRT Releases 2023 (PolitePol)
DD-WRT Releases 2023 (RSS Everything)
----------------------
Linux User #377467 counter.li.org / linuxcounter.net
Router/Version: Netgear R7800
File: dd-wrt-webupgrade.bin
Firmware: DD-WRT v3.0-r47874 std (12/18/21) (prev. DD-WRT v3.0-r47853 std (12/16/21))
Kernel: Linux 4.9.292 #607 SMP Sat Dec 18 12:16:51 +07 2021 armv7l
Mode: Gateway, SFE disabled, 2.4G and 5G wifi, Wireguard for external access, WAN to 4G, Keep Alive reboot 6:02 in the morning
Reset: No
Status: Up and running since yesterday, Ok!
Has anyone tested that shiny new feature to disable webUI access from wireless?
I don't know that is does much in this build but in r47893 it is ON by default -- both radios.
Didn't realize such till I got in the recliner with laptop last night and thought WTH.
Give PW page and when click to login then you get a 401 --- no can go. That is where a another unit as a WAP on main net is very handy
All the 'wireless' webif pages are really screwed in r47893 ... anything you do will kill httpd but it comes back up after couple minutes on the EA8500
I reckon BS is working on it
---
Oh shit -- just seen r47893 is a public release while I was typing this
It is same build I installed yesterday--- I done checksum (sha256sum):