Thanks for that info! I use those services all the time, so now I know the minimum version I have to move to if I upgrade from 33986. Thanks for logging and monitoring that ticket! _________________ WRT3200ACM 1st Gen
DD-WRT v3.0-r51440 std (1/19/23)
Upgraded from v3.0-r33986 (12/04/17)
Motorola MB8600
Comcast 1200/40
ExpressVPN OpenVPN Client Manual Config
NAS and miniDLNA: 8TB Seagate USB3
Ditto what AmesJainchill said, it's the only thing I was interested in as long as the WiFi is untouched. Thanks for checking that so quickly.
One issue, on the previous release r37139 Free and Used memory on the Status page was running about 50% for each and on this release r37305 it's running 81% Used and slowly increasing (and 19% Free). Is this going to cause any issues? It's the most Used memory I've seen on any DDWRT release since I started using it. _________________ Linksys WRT3200ACM
Currently using Linksys Firmware until DDWRT lets my ObiTalk 202 complete calls when connected via WiFi
Last used DD-WRT Version: r38326
OpenVPN server
One thing to remember if you are using a NAS drive is to mount the partition to jffs in the UUID section (Services/USB). If you don't do this and you have a lot of files the memory usage will be high like you said...If you mount the partition to jffs your memory usage should be much less...Here is mine after more than 8 hours usage since reboot...
One issue, on the previous release r37139 Free and Used memory on the Status page was running about 50% for each and on this release r37305 it's running 81% Used and slowly increasing (and 19% Free). Is this going to cause any issues? It's the most Used memory I've seen on any DDWRT release since I started using it.
One thing to remember if you are using a NAS drive is to mount the partition to jffs in the UUID section (Services/USB). If you don't do this and you have a lot of files the memory usage will be high like you said...If you mount the partition to jffs your memory usage should be much less...Here is mine after more than 8 hours usage since reboot...
OK, thank you. Everthing seems to work better after I did that but why can't I delete or paste files to the drive using Windows file explorer (no delete or paste options) but I can with my cell using ES File Explorer? All I can do using Windows is to copy from the USB to the PC, that's a pain if I have to remove it to add files. Memory is better Used 44% and Free 56%. EDIT: So much for that after 30 minutes memory is 80% Used and 20% free. _________________ Linksys WRT3200ACM
Currently using Linksys Firmware until DDWRT lets my ObiTalk 202 complete calls when connected via WiFi
Last used DD-WRT Version: r38326
OpenVPN server
I installed r37305-2018.October.10 on my WRT1900ACS_v1 as flash upgrade keeping my configs without issues. I used the Edge browser for the upgrade. Everything seems to be working without issues. I'll report if I hit any.
Kernel Version: Linux 4.9.131 #478 SMP PREEMPT Wed Oct 10 04:01:52 CEST 2018
DD-WRT config reference for my WRT1900ACS_v1: wired devices ~75, wireless ~20 clients using 5GHz-80Mhz-AC-Only & 2.4GHz-20Mhz-NG-Mixed with 2 additional APs in house (D-Link DAP-1650 - same SSID/Config, non-overlapping channels), IPv6 on, DHCP reservations for all known devices, local Raspberry Pi NTP, access rules (internet block security cameras), port forwards, no QOS, running OpenVPN server, firewall rules (OpenVPN & Guest), Guest 2.4GHz Wi-Fi segmented network/DHCP
_________________
Router: Linksys WRT1900ACS_v1 (Marvell Armada 385)
Firmware: DD-WRT v3.0-r37305 std 10/10/18
Cable Modem: Motorola MB7420
ISP: Comcast (250 Mbps down | 10 Mbps up)
Hi!
I tried to install this version from r36808, via Telnet / SSH.
I had the following problems:
Started the update I waited for the countdown indicated on the screen of 300s, after which the rototer has not restarted.
I waited again but nothing happened, I could use my network and internet but not to access the IP of the DDWRT.
I restarted the rototer manually and this time my network and internet were no longer accessible but I could open the IP of the DDWRT. I tried to make some settings but nothing.
Fortunately, Putty worked and after setting partition 1 where the Linksys FW is present, I always restarted via the command line.
At this point I found the FW Linksys and so I have I re-installed the r36808 with which I had no problems.
_________________ WRT3200acm - r41491
Last edited by turrikan on Thu Oct 11, 2018 18:36; edited 4 times in total
You will use memory if you are actively accessing the drive but the memory should recover. If not then there is another issue as mine is not doing that.
For write permissions...
Under SERVICES/NAS...In the FILE SHARING section I have mine set to
PATH mnt/sda1 NAME Router_NAS (Or whatever)
PUBLIC is Checked. ACCESS the drop down is set to Read/Write. That should give you read write.
Under USERS you can also add your Windows username and password here (And other users). Then when you try to access the NAS Windows will ask you for the password you set for the NAS. You can tell Windows to remember this so you don't need to keep doing that.
With PUBLIC checked you probably don't need to add the individual Users but that's how I have mine.
BobbyLee wrote:
OK, thank you. Everything seems to work better after I did that but why can't I delete or paste files to the drive using Windows file explorer (no delete or paste options) but I can with my cell using ES File Explorer? All I can do using Windows is to copy from the USB to the PC, that's a pain if I have to remove it to add files. Memory is better Used 44% and Free 56%. EDIT: So much for that after 30 minutes memory is 80% Used and 20% free.
You will use memory if you are actively accessing the drive but the memory should recover. If not then there is another issue as mine is not doing that.
Not actively accessing the drive and it stays at Used 80%.
DaveI wrote:
For write permissions...
Under SERVICES/NAS...In the FILE SHARING section I have mine set to
PATH mnt/sda1
/dev/sda1 is now mounted to /jffs so it doesn't give me the mnt/sda1 as an option only /jffs and /mnt but no mnt/sda1.
Any chance I could get you to PM me captures of your USB and NAS setup pages? I PM'ed you my NAS settings if you don't mind taking a look? _________________ Linksys WRT3200ACM
Currently using Linksys Firmware until DDWRT lets my ObiTalk 202 complete calls when connected via WiFi
Last used DD-WRT Version: r38326
OpenVPN server
I noticed someone with a different router reopened bug 6319 for this build.
Anybody notice not being able to see or stream to their chromecast, or not see their airprint enabled printer?
I noticed on the 10/4 build my printer wasn’t seen after 4 days. Had to restart router for it to come back. _________________ WRT3200ACM V1 r39267 std (03/22/19) OpenVPN client
@adamcarter Because of this bug I almost threw out my Klipsch G17 -- after multiple betas installed...
I hope that is not the case with this router or the 3200acm and this build.
-JM
