New Brainslayer Build 10-10-18 - R37305

Post new topic   Reply to topic    DD-WRT Forum Forum Index -> Marvell MVEBU based Hardware (WRT1900AC etc.)
Goto page 1, 2  Next
Author Message
DaveI
DD-WRT User


Joined: 06 Jul 2009
Posts: 335

PostPosted: Wed Oct 10, 2018 21:12    Post subject: New Brainslayer Build 10-10-18 - R37305 Reply with quote
Released 10-10-18
https://dd-wrt.com/support/other-downloads/?path=betas%2F2018%2F10-10-2018-r37305%2F

_________________
WRT1900ACSv2
Sponsor
DaveI
DD-WRT User


Joined: 06 Jul 2009
Posts: 335

PostPosted: Wed Oct 10, 2018 21:50    Post subject: Reply with quote
NAS/SAMBA/DLNA back WORKING!!!

Will close ticket #6453.

_________________
WRT1900ACSv2
AmesJainchill
DD-WRT Novice


Joined: 10 Aug 2017
Posts: 37
Location: MI, USA

PostPosted: Wed Oct 10, 2018 22:13    Post subject: Reply with quote
DaveI wrote:
NAS/SAMBA/DLNA back WORKING!!!

Will close ticket #6453.


Thanks for that info! I use those services all the time, so now I know the minimum version I have to move to if I upgrade from 33986. Thanks for logging and monitoring that ticket!

_________________
WRT3200ACM 1st Gen
DD-WRT v3.0-r33986 (12/04/17) std - SVN rev: 33986
Motorola MB8600
Comcast 600/20
ExpressVPN OpenVPN Client Manual Config
NAS and miniDLNA: 4TB Seagate USB3
BobbyLee
DD-WRT User


Joined: 04 Jul 2016
Posts: 131

PostPosted: Wed Oct 10, 2018 22:36    Post subject: Reply with quote
DaveI wrote:
NAS/SAMBA/DLNA back WORKING!!!

Will close ticket #6453.

Ditto what AmesJainchill said, it's the only thing I was interested in as long as the WiFi is untouched. Thanks for checking that so quickly.

One issue, on the previous release r37139 Free and Used memory on the Status page was running about 50% for each and on this release r37305 it's running 81% Used and slowly increasing (and 19% Free). Is this going to cause any issues? It's the most Used memory I've seen on any DDWRT release since I started using it.

_________________
Linksys WRT3200ACM
Currently using Linksys Firmware until DDWRT lets my ObiTalk 202 complete calls when connected via WiFi
Last used DD-WRT Version: r38326
OpenVPN server
mainkaunhoon
DD-WRT Novice


Joined: 16 Jul 2016
Posts: 24

PostPosted: Thu Oct 11, 2018 3:02    Post subject: Reply with quote
Upgraded my WRT1200ACv1. So far so good. Thanks for this!
_________________
Device: Linksys WRT1200AC v1
New:Firmware Firmware: DD-WRT v3.0-r37305 std (10/10/1Cool
OLD:Firmware DD-WRT v3.0-r36006 std ( 05/23/18 )
DaveI
DD-WRT User


Joined: 06 Jul 2009
Posts: 335

PostPosted: Thu Oct 11, 2018 8:13    Post subject: Reply with quote
One thing to remember if you are using a NAS drive is to mount the partition to jffs in the UUID section (Services/USB). If you don't do this and you have a lot of files the memory usage will be high like you said...If you mount the partition to jffs your memory usage should be much less...Here is mine after more than 8 hours usage since reboot...

Memory
Total Available
499.9 MB / 512.0 MB
Free
433.0 MB / 499.9 MB
Used
66.8 MB / 499.9 MB
Buffers
7.3 MB / 66.8 MB
Cached
16.3 MB / 66.8 MB
Active
18.0 MB / 66.8 MB
Inactive
10.0 MB / 66.8 MB


BobbyLee wrote:

One issue, on the previous release r37139 Free and Used memory on the Status page was running about 50% for each and on this release r37305 it's running 81% Used and slowly increasing (and 19% Free). Is this going to cause any issues? It's the most Used memory I've seen on any DDWRT release since I started using it.

_________________
WRT1900ACSv2
BobbyLee
DD-WRT User


Joined: 04 Jul 2016
Posts: 131

PostPosted: Thu Oct 11, 2018 8:58    Post subject: Reply with quote
DaveI wrote:
One thing to remember if you are using a NAS drive is to mount the partition to jffs in the UUID section (Services/USB). If you don't do this and you have a lot of files the memory usage will be high like you said...If you mount the partition to jffs your memory usage should be much less...Here is mine after more than 8 hours usage since reboot...


OK, thank you. Everthing seems to work better after I did that but why can't I delete or paste files to the drive using Windows file explorer (no delete or paste options) but I can with my cell using ES File Explorer? All I can do using Windows is to copy from the USB to the PC, that's a pain if I have to remove it to add files. Memory is better Used 44% and Free 56%. EDIT: So much for that after 30 minutes memory is 80% Used and 20% free.

_________________
Linksys WRT3200ACM
Currently using Linksys Firmware until DDWRT lets my ObiTalk 202 complete calls when connected via WiFi
Last used DD-WRT Version: r38326
OpenVPN server
Monza
DD-WRT User


Joined: 01 Jul 2018
Posts: 175

PostPosted: Thu Oct 11, 2018 12:43    Post subject: Reply with quote
Updated WRT1200ACv1 from r37012 to r37305 with no reset, no issues.

No syslog OpenVPN red warnings like I started getting in r37139 only the usual yellow warnings.
derWolfMan
DD-WRT User


Joined: 20 Jan 2017
Posts: 84

PostPosted: Thu Oct 11, 2018 14:22    Post subject: Reply with quote
I installed r37305-2018.October.10 on my WRT1900ACS_v1 as flash upgrade keeping my configs without issues. I used the Edge browser for the upgrade. Everything seems to be working without issues. I'll report if I hit any.

Kernel Version: Linux 4.9.131 #478 SMP PREEMPT Wed Oct 10 04:01:52 CEST 2018

DD-WRT config reference for my WRT1900ACS_v1: wired devices ~75, wireless ~20 clients using 5GHz-80Mhz-AC-Only & 2.4GHz-20Mhz-NG-Mixed with 2 additional APs in house (D-Link DAP-1650 - same SSID/Config, non-overlapping channels), IPv6 on, DHCP reservations for all known devices, local Raspberry Pi NTP, access rules (internet block security cameras), port forwards, no QOS, running OpenVPN server, firewall rules (OpenVPN & Guest), Guest 2.4GHz Wi-Fi segmented network/DHCP
_________________
Router: Linksys WRT1900ACS_v1 (Marvell Armada 385)
Firmware: DD-WRT v3.0-r37305 std 10/10/18
Cable Modem: Motorola MB7420
ISP: Comcast (250 Mbps down | 10 Mbps up)
turrikan
DD-WRT Novice


Joined: 04 Mar 2018
Posts: 12
Location: Italy

PostPosted: Thu Oct 11, 2018 17:03    Post subject: Reply with quote
Hi!
I tried to install this version from r36808, via Telnet / SSH.
I had the following problems:

    Started the update I waited for the countdown indicated on the screen of 300s, after which the rototer has not restarted.

    I waited again but nothing happened, I could use my network and internet but not to access the IP of the DDWRT.

    I restarted the rototer manually and this time my network and internet were no longer accessible but I could open the IP of the DDWRT. I tried to make some settings but nothing.

    Fortunately, Putty worked and after setting partition 1 where the Linksys FW is present, I always restarted via the command line.

    At this point I found the FW Linksys and so I have I re-installed the r36808 with which I had no problems.

_________________
WRT3200acm - r41491


Last edited by turrikan on Thu Oct 11, 2018 18:36; edited 4 times in total
DaveI
DD-WRT User


Joined: 06 Jul 2009
Posts: 335

PostPosted: Thu Oct 11, 2018 17:48    Post subject: Reply with quote
You will use memory if you are actively accessing the drive but the memory should recover. If not then there is another issue as mine is not doing that.

For write permissions...

Under SERVICES/NAS...In the FILE SHARING section I have mine set to
PATH mnt/sda1 NAME Router_NAS (Or whatever)
PUBLIC is Checked. ACCESS the drop down is set to Read/Write. That should give you read write.

Under USERS you can also add your Windows username and password here (And other users). Then when you try to access the NAS Windows will ask you for the password you set for the NAS. You can tell Windows to remember this so you don't need to keep doing that.
With PUBLIC checked you probably don't need to add the individual Users but that's how I have mine.


BobbyLee wrote:


OK, thank you. Everything seems to work better after I did that but why can't I delete or paste files to the drive using Windows file explorer (no delete or paste options) but I can with my cell using ES File Explorer? All I can do using Windows is to copy from the USB to the PC, that's a pain if I have to remove it to add files. Memory is better Used 44% and Free 56%. EDIT: So much for that after 30 minutes memory is 80% Used and 20% free.

_________________
WRT1900ACSv2
BobbyLee
DD-WRT User


Joined: 04 Jul 2016
Posts: 131

PostPosted: Thu Oct 11, 2018 18:35    Post subject: Reply with quote
DaveI wrote:
You will use memory if you are actively accessing the drive but the memory should recover. If not then there is another issue as mine is not doing that.

Not actively accessing the drive and it stays at Used 80%.

DaveI wrote:
For write permissions...

Under SERVICES/NAS...In the FILE SHARING section I have mine set to
PATH mnt/sda1

/dev/sda1 is now mounted to /jffs so it doesn't give me the mnt/sda1 as an option only /jffs and /mnt but no mnt/sda1.

Any chance I could get you to PM me captures of your USB and NAS setup pages? I PM'ed you my NAS settings if you don't mind taking a look?

_________________
Linksys WRT3200ACM
Currently using Linksys Firmware until DDWRT lets my ObiTalk 202 complete calls when connected via WiFi
Last used DD-WRT Version: r38326
OpenVPN server
Adamcarter
DD-WRT User


Joined: 09 Aug 2016
Posts: 235

PostPosted: Thu Oct 11, 2018 18:55    Post subject: Reply with quote
I noticed someone with a different router reopened bug 6319 for this build.

Anybody notice not being able to see or stream to their chromecast, or not see their airprint enabled printer?

I noticed on the 10/4 build my printer wasn’t seen after 4 days. Had to restart router for it to come back.

_________________
WRT3200ACM V1 r39267 std (03/22/19) OpenVPN client
Juni0rM1nt
DD-WRT Novice


Joined: 26 Feb 2016
Posts: 27
Location: DM-Phobos

PostPosted: Thu Oct 11, 2018 19:19    Post subject: Reply with quote
@adamcarter Because of this bug I almost threw out my Klipsch G17 -- after multiple betas installed...
I hope that is not the case with this router or the 3200acm and this build.
-JM
DaveI
DD-WRT User


Joined: 06 Jul 2009
Posts: 335

PostPosted: Thu Oct 11, 2018 20:08    Post subject: Reply with quote
BobbyLee,

Replied with Screenshots in PM.

BobbyLee wrote:

Not actively accessing the drive and it stays at Used 80%.


_________________
WRT1900ACSv2
Goto page 1, 2  Next Display posts from previous:    Page 1 of 2
Post new topic   Reply to topic    DD-WRT Forum Forum Index -> Marvell MVEBU based Hardware (WRT1900AC etc.) All times are GMT

Navigation

 
Jump to:  
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
You cannot attach files in this forum
You cannot download files in this forum