Uraniumhazee
DD-WRT Novice
Joined: 02 Aug 2018
Posts: 1
|
 Posted: Thu Aug 02, 2018 17:17 Post subject: WA701ND v2 DDWrt No Wifi Tab / Original Firmware Not Work |
 |
My router was bricked so i bought a USB UART converter for a serial connection.
There is no DDwrt firmware for wa701nd but
TP-Link TL-MR3020 is also same with WA701ND and i used MR30 DDwrt. İn below link somebody tried and succeeded.
This is source: http://techychirag.blogspot.com/2014/12/dd-wrt-for-tp-link-tl-wa701nd-v2.html
ddwrt fow wa701nd v2
https://drive.google.com/file/d/0B1qUytrATPCeVHJESXpkOUMwQ3c/view
Plan is basic.
My codes for putty.
| Code: | setenv ipaddr 192.168.1.111
setenv serverip 192.168.1.100
printenv
tftpboot 0x81000000 firmware.bin
erase 0x9f020000 +0x3c0000
cp.b 0x81000000 0x9f020000 0x3c0000
reset |
I connected router with putty. I flashed successfully and when I visit 192.168.1.1 DDwrt control panel, i mean admin panel is working.
But there are no wifi tab, wifi sections on the ddwrt panel.
it is so strange i flashed oepnwrt too and same, no wifi tab in his control panel too..
----------------------------------------------
/////////////////////////////////////////////
#################################################
Second problem is original firmware.
My original firmwware is about 4mb and when i flash it gives big file uncompressed.
So what i did?
1) i found stripped version.
2) Also i learned that from 00000000 hex to 00020200 is bootloader so i deleted 0000000 to 00020200 and i prepared a 3,840mb clean firmware.
3) also there is a tool http://www.chrysocome.net/dd
in windows with this tools the boodloader section can be delete. COMMAND: dd if=ori.bin of=mod.bin skip=257 bs=512 (Windows/CD)
When i flashed original stripped firmware, opwenwrt or ddwrt
3 led On= power, device is working gear led, and lan led.
and below the device with orginal / without bootloader firmware
| Code: |
U-Boot 1.1.4 (Jun 20 2016 - 15:22:27)
AP121 (ar9330) U-boot
DRAM: 32 MB
led turning on for 1s...
id read 0x100000ff
flash size 4194304, sector count = 64
Flash: 4 MB
Using default environment
In: serial
Out: serial
Err: serial
Net: ag7240_enet_initialize...
No valid address in Flash. Using fixed address
No valid address in Flash. Using fixed address
: cfg1 0x5 cfg2 0x7114
eth0: 00:03:7f:09:0b:ad
ag7240_phy_setup
eth0 up
: cfg1 0xf cfg2 0x7214
eth1: 00:03:7f:09:0b:ad
athrs26_reg_init_lan
ATHRS26: resetting s26
ATHRS26: s26 reset done
ag7240_phy_setup
eth1 up
eth0, eth1
Autobooting in 1 seconds
## Booting image at 9f020000 ...
Uncompressing Kernel Image ... OK
Starting kernel ...
Booting AR9330(Hornet)...
Linux version 2.6.31--LSDK-9.2.0.312 (tomcat@buildserver) (gcc version 4.3.3 (GC C) ) #129 Mon Jun 20 15:28:34 CST 2016
flash_size passed from bootloader = 4
CPU revision is: 00019374 (MIPS 24Kc)
Determined physical RAM map:
memory: 02000000 @ 00000000 (usable)
User-defined physical RAM map:
memory: 02000000 @ 00000000 (usable)
Zone PFN ranges:
Normal 0x00000000 -> 0x00002000
Movable zone start PFN for each node
early_node_map[1] active PFN ranges
0: 0x00000000 -> 0x00002000
Built 1 zonelists in Zone order, mobility grouping on. Total pages: 8128
Kernel command line: console=ttyS0,115200 root=31:02 rootfstype=squashfs init=/s bin/init mtdparts=ar7240-nor0:128k(u-boot),1024k(kernel),2816k(rootfs),64k(confi g),64k(ART) mem=32M
PID hash table entries: 128 (order: 7, 512 bytes)
Dentry cache hash table entries: 4096 (order: 2, 16384 bytes)
Inode-cache hash table entries: 2048 (order: 1, 8192 bytes)
Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
Writing ErrCtl register=00000000
Readback ErrCtl register=00000000
Memory: 29876k/32768k available (1885k kernel code, 2892k reserved, 520k data, 1 16k init, 0k highmem)
Hierarchical RCU implementation.
NR_IRQS:128
plat_time_init: plat time init done
Calibrating delay loop... 266.24 BogoMIPS (lpj=532480)
Mount-cache hash table entries: 512
NET: Registered protocol family 16
===== ar7240_platform_init: 0
Requeset IRQ for jumpstart with JUMPSTART_GPIO=26
bio: create slab <bio-0> at 0
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 1024 (order: 1, 8192 bytes)
TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
TCP: Hash tables configured (established 1024 bind 1024)
TCP reno registered
NET: Registered protocol family 1
AR7240 GPIOC major 0
squashfs: version 4.0 (2009/01/31) Phillip Lougher
NTFS driver 2.1.29 [Flags: R/O].
msgmni has been set to 58
alg: No test for lzma (lzma-generic)
alg: No test for stdrng (krng)
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered (default)
Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled
ttyS0: detected caps 00000000 should be 00000100
serial8250.0: ttyS0 at MMIO 0xb8020000 (irq = 19) is a 16550A
console [ttyS0] enabled
PPP generic driver version 2.4.2
NET: Registered protocol family 24
cmdlinepart partition parsing not available
set partition boot
set partition kernel
set partition rootfs
set partition config
set partition art
set partition ▒
Searching for RedBoot partition table
5 RedBoot partitions found on MTD device ar7240-nor0
Creating 5 MTD partitions on "ar7240-nor0":
0x000000000000-0x000000020000 : "boot"
0x000000020000-0x000000120000 : "kernel"
0x000000120000-0x0000003e0000 : "rootfs"
0x0000003e0000-0x0000003f0000 : "config"
0x0000003f0000-0x000000400000 : "art"
->Oops: flash id 0xef4016 .
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
Port Status 1c000004
ar7240-ehci ar7240-ehci.0: ATH EHCI
ar7240-ehci ar7240-ehci.0: new USB bus registered, assigned bus number 1
ehci_reset Intialize USB CONTROLLER in host mode: 3
ehci_reset Port Status 1c000000
ar7240-ehci ar7240-ehci.0: irq 3, io mem 0x1b000000
ehci_reset Intialize USB CONTROLLER in host mode: 3
ehci_reset Port Status 1c000000
ar7240-ehci ar7240-ehci.0: USB 2.0 started, EHCI 1.00
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 1 port detected
TCP cubic registered
NET: Registered protocol family 17
802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
All bugs added by David S. Miller <davem@redhat.com>
ar7240wdt_init: Registering WDT success
VFS: Mounted root (squashfs filesystem) readonly on device 31:2.
Freeing unused kernel memory: 116k freed
init started: BusyBox v1.01 (2016.06.20-07:32+0000) multi-call binary
This Board use 2.6.31
xt_time: kernel timezone is -0000
nf_conntrack version 0.5.0 (512 buckets, 5120 max)
ip_tables: (C) 2000-2006 Netfilter Core Team
insmod: cannot open module `/lib/modules/2.6.31/kernel/iptable_raw.ko': No such file or directory
insmod: cannot open module `/lib/modules/2.6.31/kernel/flashid.ko': No such file or directory
PPPoL2TP kernel driver, V1.0
PPTP driver version 0.8.3
insmod: cannot open module `/lib/modules/2.6.31/kernel/harmony.ko': No such file or directory
insmod: cannot open module `/lib/modules/2.6.31/kernel/af_key.ko': No such file or directory
insmod: cannot open module `/lib/modules/2.6.31/kernel/xfrm_user.ko': No such fi le or directory
(none) mips #129 Mon Jun 20 15:28:34 CST 2016 (none)
(none) login: Now flash open!
Now flash open!
ATHR_GMAC: Length per segment 1536
ATHR_GMAC: fifo cfg 3 01f00140
2
ATHR_GMAC: Max segments per packet : 1
ATHR_GMAC: Max tx descriptor count : 164
ATHR_GMAC: Max rx descriptor count : 196
ATHR_GMAC: Mac capability flags : 10004D83
1
ATHR_GMAC: Max segments per packet : 1
ATHR_GMAC: Max tx descriptor count : 96
ATHR_GMAC: Max rx descriptor count : 252
ATHR_GMAC: Mac capability flags : 4403
athr_gmac_ring_alloc Allocated 1536 at 0x81c54000
athr_gmac_ring_alloc Allocated 4032 at 0x81d42000
Setting Drop CRC Errors, Pause Frames and Length Error frames
Setting PHY...mac 0
athr_gmac_ring_alloc Allocated 2624 at 0x81e41000
athr_gmac_ring_alloc Allocated 3136 at 0x81f0d000
Setting Drop CRC Errors, Pause Frames and Length Error frames
ATHRS26: resetting s26
ATHRS26: s26 reset done
Setting PHY...mac 1
ATH_MAC_TIMER: Current RxFsm for GMAC unit:1 is 0x0 >> 11 is 0x0
device eth0 entered promiscuous mode
Now flash open!
nf_conntrack_rtsp v0.6.21 loading
nf_nat_rtsp v0.6.21 loading
CHIP REV ID: 111
dk_dev_init::status after register_chrdev(dk) = 0
Base Phsycal address :0x18100000
DK::Add client 0
DK::Reg phy addr = 18100000 vir Addr = b8100000
DK::Irq = 2
DK::Allocated 0x200000 bytes memory
DK::memory vir Addr = 81400000 phy Addr = 1400000
DK::Reg write @ 0xb8100024 : 0x0000
Device Status is : 0x0
|
printenv
| Code: | hornet> printenv
bootargs=console=ttyS0,115200 root=31:02 rootfstype=squashfs init=/sbin/init mtdparts=ar7240-nor0:256k(u-boot),64k(u-boot-env),2752k(rootfs),896k(uImage),64k(NVRAM),64k(ART)
bootcmd=bootm 0x9f020000
bootdelay=1
baudrate=115200
ethaddr=0xba:0xbe:0xfa:0xce:0x07:0x41
ipaddr=192.168.1.111
serverip=192.168.1.100
stdin=serial
stdout=serial
stderr=serial
ethact=eth0
|
With original firmware no wifi led on
and there are no login panel.
192.168.0.254 is the stock firmware panel but the page can not be opened and also wifi is not active with original firmware.
original firmware:
https://www.tp-link.com/tr/download/TL-WA701ND.html#Firmware
V2 version
What am i doing wrong?
is the router is broken?
in all firmwares device not working.
Please help me to fix this device. |
|
