This build thread is for reporting successes and problem with loading this experimental test build. This is important info for developers and users. Always state your hardware and SPECIFIC build (e.g. 29000_NEWD-2_K2.6_mega-nv64k.bin). Do not ask questions about your specific router or how to configure it in this thread; create your own thread to discuss any specific problems you have or need resolved. Please also do not respond to such questions. This thread is to report info, not to seek it. Posts that do not add to understanding this build will be deleted. Make sure you know how to flash properly and the risk before using this build. It is important to adhere to these requirements, to keep this thread from becoming impossibly long and useless. If you don't know what build to flash and how to flash properly and have a means of recovery if things should go wrong, do NOT flash this experimental test build.
Last edited by Mile-Lile on Wed Aug 01, 2018 13:23; edited 1 time in total
Joined: 24 Feb 2013 Posts: 1634 Location: Belgrade
Posted: Sun Jul 29, 2018 10:58 Post subject:
Router Model Netgear R6250
Firmware Version DD-WRT v3.0-r36410 std (07/28/1
Kernel Version Linux 4.4.144 #3591 SMP Thu Jul 26 13:46:00 CEST 2018 armv7l
Status: Working (VAPs, Unbound,QoS, Speedchecker client, OpenVPN server, Remote Access etc.)
Reset: Yes! Did erase nvram && reboot and did new setup from "scratch"
Errors: None. Note: For working VAPs, you need to do setup config from scratch and after adding VAP you need to reboot unit...
BS, Chris, Markus and Peter thank you very much for your work!!!
Posted: Sun Jul 29, 2018 11:33 Post subject: E3000
Router/Version: Linksys E3000
Firmware: DD-WRT v3.0-r36410 mega ( 07/28/18 )
Kernel: LLinux 3.10.108-d4 #20248 Sat Jul 28 12:49:17 CEST 2018 mips
Previous: DD-WRT v3.0-r35531 mega
Mode/Status: Gateway/AP
Setup: Using DNSmasq, DDNS
Reset: No
Issues/Errors: None so far
E2500
DD-WRT v3.0-r36410 [07/28/18]
Linux 3.10.108-d4 #20248 Sat Jul 28 12:49:17 CEST 2018 mips
GUI install [dd-wrt.v24-36410_NEWD-2_K3.x_mega.bin] over r33555
GUI Reset
Test router....
MAC addresses good and VAP is now working well.
Joined: 09 Nov 2014 Posts: 314 Location: Bakersfield, CA
Posted: Sun Jul 29, 2018 18:45 Post subject:
Router Model: 2x Linksys E3000
Firmware: dd-wrt.v24-36410_NEWD-2_K3.x_mega-e3000.bin
Previous: dd-wrt.v24-36330_NEWD-2_K3.x_mega-e3000.bin
Kernel: Linux 3.10.108-d4 #20248 Sat Jul 28 12:49:17 CEST 2018 mips
Status: Both working as basic client bridge routers. Speedtests are good. Seems solid so far.
Reset: No
Errors: None thus far, will report any I may find.
My Trendnet TEW811DRU unit goes through the update process and then stays at the old firmware, it doesn't update to the new one. EDIT: It worked the second time I tried.
Router Model: Trendnet TEW811DRU
Firmware: DD-WRT v3.0-r36410 mini (07/28/1 Kernel: Linux 4.4.144 #3594 Sat Jul 28 07:50:48 CEST 2018 armv7l
Status: Working as a basic AC only client bridge router. Speedtests are good. Seems solid so far.
Reset: No
Errors: None thus far, will report any I may find. _________________ Deployed Routers:
Netgear R7800 - 1x build 46979
- Gateway (USB /w Entware, CAKE QoS)
Netgear R7000 - 3x build 46979
Joined: 13 Aug 2013 Posts: 6870 Location: Romerike, Norway
Posted: Sun Jul 29, 2018 19:36 Post subject:
Router Model: Asus RT-AC66U A1
Firmware: DD-WRT v3.0-r36410 giga (07/28/1 Previous: 36330
Kernel: Linux 3.10.108-d4 #20232 Sat Jul 28 12:33:46 CEST 2018 mips
Status: Working. VAP is also working and can be connected to.
Reset: Yes
Errors: None thus far, will report any I may find.
Router/Version: Asus RT-AC88U
Firmware: DD-WRT v3.0-r36410 std
Previous: r36154
Kernel: 4.4.144 #3596 SMP Sat Jul 28 07:59:16 CEST 2018 armv7l GNU/Linux
Mode: AP/router
Status: OK
Reset: No
Issues/Errors: None so far
Joined: 08 May 2018 Posts: 14246 Location: Texas, USA
Posted: Sun Jul 29, 2018 20:36 Post subject:
Router/Version: Linksys E4200 v1
Firmware: DD-WRT v3.0-r36410 mega ( 07/28/18 )
Kernel: Linux 3.10.108-d4 #20248 Sat Jul 28 12:49:17 CEST 2018 mips
Previous: DD-WRT v3.0-r36330 mega ( 07/16/18 )
Firmware file used: dd-wrt.v24-36410_NEWD-2_K3.x_mega-e4200.bin
Reset; Yes; Reset via webGUI (reboot), Firmware upgrade w/reset to defaults (httpd crash!), (wait 5 minutes, power cycled), configured previous settings manually (reboot), re-configured basic wireless (reboot)
Mode: Gateway/AP
Status: OK
Issues/Errors: HTTPD crashed after firmware flashed (again!) with no report of upgrade successful via the webGUI. Basic wireless settings, channels default to auto after initial re-configuration and reboot. Had to go back in, click save, re-configure channels, save, reboot. Gratuitous serial console log (forgot to have serial up and running initially, but) and final reboot syslog attached (I should probably save the first reboot syslog next time)....
EDIT: Httpd error messages (nothing new)
Jul 29 20:57:40 DD-WRT daemon.err httpd[1383]: Request Error Code 401: Authorization required. please note that the default username is "root" in all newer releases
Jul 29 20:57:51 DD-WRT daemon.err httpd[1383]: Request Error Code 404: File favicon.ico not found.
Jul 30 13:51:27 DD-WRT daemon.err httpd[1383]: Request Error Code 408: No request appeared within a reasonable time period.
Joined: 09 Nov 2014 Posts: 314 Location: Bakersfield, CA
Posted: Sun Jul 29, 2018 21:58 Post subject:
Will someone point me to a build that works as a repeater? This build isn't accepting connections. I've had it running for 100+ days, decided to update it, and the repeater setup like I had it doesn't work. No connections to the broadcasted repeated signal. _________________ Deployed Routers:
Netgear R7800 - 1x build 46979
- Gateway (USB /w Entware, CAKE QoS)
Netgear R7000 - 3x build 46979
Router/Version: Netgear R7000
Firmware: DD-WRT v3.0-r36410 std ( 07/28/18 )
Kernel: Linux 4.4.144 #3591 SMP Thu Jul 26 13:46:00 CEST 2018 armv7l
Previous: r36330
Mode/Status: Gateway / working
Reset: no
Issues/Errors: On numerous attempts, my router wouldn't take this version. Web update resulted in web GUI becoming unresponsive. Command line update caused SSH to become unresponsive. In both cases, the router continues to work. Each time, a reboot of the router restored web GUI and command line functions. A command line update eventually worked, and things are working well (after limited use and testing).
Uptime: 47m
Temperatures: CPU 68.0 °C / WL0 48.0 °C / WL1 51.5 °C
Joined: 24 Feb 2013 Posts: 1634 Location: Belgrade
Posted: Mon Jul 30, 2018 8:23 Post subject:
SinCalChewy wrote:
Will someone point me to a build that works as a repeater? This build isn't accepting connections. I've had it running for 100+ days, decided to update it, and the repeater setup like I had it doesn't work. No connections to the broadcasted repeated signal.
use latest publicly available build (36410 curently), then you have to erase nvram and set it up again from "scratch"... do not use previous backedup nvram configs...
if that doesn't work for you, you can try "Atheros Repeating" - Client bridge + VAP (AP) in router mode (no NAT)...
