[james1795]

Kong's DD-WRT test build v3.0-r36400M kongac (26/07/2018) has been released: http://desipro.de/ddwrt/K3-AC-Arm/TEST/

Your reports for Broadcom units are greatly appreciated !
Router:
Firmware:
Kernel:
Status:
Reset:
Errors:

This build thread is for reporting successes and problem with loading this experimental test build. This is important info for developers and users. Always state your hardware and SPECIFIC build (e.g. 29440_NEWD-2_K2.6_mega-nv64k.bin). Do not ask questions about your specific router or how to configure it in this thread; create your own thread to discuss any specific problems you have or need resolved. Please also do not respond to such questions. This thread is to report info, not to seek it. Posts that do not add to understanding this build will be deleted. Make sure you know how to flash properly and the risk before using this build. It is important to adhere to these requirements, to keep this thread from becoming impossibly long and useless. If you don't know what build to flash and how to flash properly and have a means of recovery if things should go wrong, do NOT flash this experimental test build.

[blackraiin]

Router: D-Link DIR-868L A1
Firmware: DD-WRT v3.0-r36400M kongac ( 07/26/18 )
Kernel: Linux 4.4.144-rc1 #582 SMP Thu Jul 26 18:11:52 CEST 2018 armv7l
Status: Working
Reset: Yes
Errors: None

I am now able to connect to the 5GHz

[grc]

Router: Netgear r6300v2
Firmware: DD-WRT v3.0-r36400M kongac ( 07/26/18 )
Reset: yes 2x, erase nvram
Errors: yes

[blenn]

Router: Netgear R8000
Firmware: DD-WRT v3.0-r36400M kongac ( 07/26/18 )
Kernel: Linux 4.4.144-rc1 #582 SMP Thu Jul 26 18:11:52 CEST 2018 armv7l
Status: Working
Reset: No
Errors: None

Fairly simple setup with 2.4GHz + 5GHz + 5GHz AP and a few LAN clients. All working fine with no trace of earlier dropouts!
Thank you Kong!

[decompiled]

Router: R7000
Firmware: DD-WRT v3.0-r36400
Kernel: Linux 4.4.144-rc1 #582 SMP Thu Jul 26 18:11:52 CEST 2018 armv7l
Status: Working
Reset: No
Errors: No

Upgraded from latest. Using features static wan, dhcp lan, qos, port forwarding, sshd, ntp, link aggregation and both radios.

[diogosena]

Router: AC68U
Firmware: DD-WRT v3.0-r36400
Kernel: Linux 4.4.144-rc1 #582 SMP Thu Jul 26 18:11:52 CEST 2018 armv7l
Status: Not Working
Reset: No
Errors: Yes

My setup have both radios as wireless repeaters, and each radio with a secondary VAP.
Can't connect to any of the VAPS.
Back to stable.

[thunderhead]

Wondering if the disconnect issue from the last test build is fixed:

[LiloBzH]

Hi!

@kong, Why do you ignore questions about problem with remote acess in HTTPS ?
or it's patched now ?

Thank you !

[Bernadoe]

Router: Netgear R7000
Firmware: DD-WRT v3.0-r36400M kongac (07/26/2018)
Kernel: Linux 4.4.144-rc1 #582 SMP Thu Jul 26 18:11:52 CEST 2018 armv7l
Status: Working
Reset: No
Previous: 36330
Errors: No

CPU Temperature : 59.7 °C / WL0 50.0 °C / WL1 52.0 °C

Working very well :
Router mode : DHCP
SFE Enable
STP Enable
DNSMasq
Encrypt DNS
Cache DNSSEC data
Validate DNS Replies (DNSSEC)
Local DNS
No DNS Rebind
Query DNS in Strict Order
SPI Firewall
Usb
Nas, Samba, JFFS2,
MAC Filter
wl0, wl1
Vpn (OpenVPN Client)

Kong and BS: Thanks for all your good work!

without VPN

[Fahrstufensensor]

Router: Netgear R7000 + R8000
Firmware: DD-WRT v3.0-r36400M kongac (07/26/2018)
Kernel: Linux 4.4.144-rc1 #582 SMP Thu Jul 26 18:11:52 CEST 2018 armv71

Status: not working

Upgraded: From 35550M via ddup --flash-latest

Reset: No

Errors: Virtual Interfaces not working for Guest Access

R7000 config:

no DHCP
wl0 NG-Mixed WEP2/AES with fixed channels + one virtual i/f
wl1 AC/N-mixed WEP2/AES with auto channel + one virtual i/f
VLAN for guest WLAN separation


R8000:
same as R7000, plus
DHCP
QoS

Kong: Thanks for all your good work!

fahrstufensensor

[eywong]

Router: Asus RT-AC68U (H/W Ver: A1)
Firmware: DD-WRT v3.0-r36400M kongac (07/26/18)
Previous: DD-WRT v3.0-r36325M kongac (07/19/18)
Kernel: Linux 4.4.144-rc1 #582 SMP Thu Jul 26 18:11:52 CEST 2018 armv7l
Previous: Linux 4.4.140 #574 SMP Thu Jul 19 23:21:12 CEST 2018 armv7l
Status: ok
Reset: no (ddup --flash-latest)
Errors: no
Uptime: 22:55

wl0: AP / NG-Mixed / Ch 11
Channel Width: 20 MHz
wl1: AP / AC/N-Mixed / Ch 52 + 54
Channel Width: Wide VHT80 (80 MHz)
Extension Channel: lower lower
DHCP Server: Enabled - Running
Static Leases: 4 hardwired NAS, 1 wireless printer
NTP Client: Enable
Server IP/Name: us.pool.ntp.org
IPv6: Disable

[hurleyp]

Router/Version: Netgear R7000
Firmware: v3.0-r36400M kongac (07/26/18 )
Kernel: Linux 4.4.144-rc1 #582 SMP Thu Jul 26 18:11:52 CEST 2018 armv7l
Previous: v3.0-r36070M kongac (05/31/18 )
Mode/Status: Up and runniung for approx. 15 hours
Reset: Soft boot before and after ddup
Issues/Errors: None

Upgraded via "ddup --flash-latest".

No 'erase nvram' this time, but I ran that command and re-entered all settings by hand after rolling back to r36070 from r36325.

The multiple repeated NAS stop/restart messages I encountered in r36325 no longer appear, and wireless connectivity is solid.

The temperatures are good: CPU 59.7 °C / WL0 46.5 °C / WL1 49.4 °C (The R7000 is wall-mounted.)

Current basic R7000 setup (subject to change of course):
- SFE - Off
- Static WAN IP
- LAN DHCP Enabled
- IPv4 only
- 1 wireless VLAN on wl0
- Encrypt DNS disabled
- Wireless: Regulatory Domain = UNITED_STATES, wl0 Mixed (ch. 1), wl1 NA-Mixed (ch. 161 + 159), AES
- SNMP enabled, SSH enabled, Telnet disabled
- Firewall enabled, Log Level high
- Syslog: remote to Logentries. klogd: disabled.
- USB support - Off
- NO: ttraf, VNC, Zabbix, VPN, Radius, OpenVPN
- NO: UPnP, DMZ, QoS
- NO: Samba, CIFS, JFFS2, miniDLNA, Entware, Optware