Hi, I bought a tp link 940n v6 but it is not available in the list of supported hardware, can you give me a hand? is there a way to solve the problem? Thanks in advance
Hello, I also own a 940N v6 (EU), and have tried the file which was posted in the first page.
The flashing was done through TFTP (web gui didn't work), which made the router stuck in a reboot loop like another user described. I was able to unbrick the router by TFTPing the stock image.
Is there anything I can do to make supported FW possible for v6?
Posted: Sat Feb 02, 2019 12:49 Post subject: Re: Test Files - EU
Xithyl wrote:
ian5142 wrote:
Here are some more test files for the 940N v6 - EU only.
Not tested by me.
Thanks, I'll try them as soon as I unbrick my router
Had a bit of a misfortune trying to flash back to original from openwrt.
Off-topic but I would appreciate it if anyone knows this, is it necessary to short pins in order to achieve serial connection? Right now I connected Rx to Tx, Tx to Rx, and ground to ground, am I doing something wrong?
If you're using serial connection for wr940n to flash dd-wrt, then don't. Try my method, it's simple as a pie
Hi there,
I managed to flash my router with the latest firmware on this thread. Apart from the blinking LED, it's working perfectly.
I do have one issue, why cannot I see hard wired devices connected to the same router? I get a destination host unreachable error.
Googling appears to indicate that there is a bug in the firmware?
I believe if that is the case, there is a command you can run but I would appreciate it if you could tell me how and where to run the command which is the following:
swconfig dev eth1 set enable_vlan 1
swconfig dev eth1 set apply
I've tried to run it through putty and the command line on the router config page, but appears to just time out.
Please can someone advise?
(I can ping wireless devices such as my smart TV).
Thanks.
Save your commands as startup under Administration - Commands page.
Then, reboot.
If not working, save the following commands as startup. (Just paste them and save as startup. The earlier commands will be replaced with the newer ones.)
swconfig dev eth0 set enable_vlan 1
swconfig dev eth0 set apply
Sorry if I'm posting on the wrong thread, I'm really new to this sort of forums...
Hi guys, I just bought a TL-WR940N v6 BR and been getting the same 18005 error message... is it the same problem than in v5? Any kind soul to modify the file to be usable in BR? Thanks in advance.
V6 usually means V6.X. So V6.1 should work with the V6 file. _________________ Before asking a question on the forums, update dd-wrt: Where do I download firmware? I suggest reading it all.
QCA Best WiFi Settings
Some dd-wrt wiki pages are up to date, others are not. PM me if you find an old one.
Atheros:
Netgear R7800 x3 - WDS AP / station, gateway, QoS
TP-Link Archer C7 v2 x2 - WDS Station
TP-Link TL-WDR3600 v1 - WDS Station
TP-Link 841nd v8 - NU
D-Link 615 C1/E3/I1 x 7 - 1 WDS station
D-Link 825 B1 - NU
D-Link 862L A1 x2 - WDS Station
Netgear WNDR3700v2 - NU
UBNT loco M2 x2 - airOS
Broadcom
Linksys EA6400 - Gateway, QoS
Asus N66U - AP
Netgear WNDR3700v3 - not used
MediaTek
UBNT EdgeRouter X - switch
VPN on that router, expect no more than 10MB/s through the VPN. And that is pushing it. It is not very powerful at all. _________________ Before asking a question on the forums, update dd-wrt: Where do I download firmware? I suggest reading it all.
QCA Best WiFi Settings
Some dd-wrt wiki pages are up to date, others are not. PM me if you find an old one.
Atheros:
Netgear R7800 x3 - WDS AP / station, gateway, QoS
TP-Link Archer C7 v2 x2 - WDS Station
TP-Link TL-WDR3600 v1 - WDS Station
TP-Link 841nd v8 - NU
D-Link 615 C1/E3/I1 x 7 - 1 WDS station
D-Link 825 B1 - NU
D-Link 862L A1 x2 - WDS Station
Netgear WNDR3700v2 - NU
UBNT loco M2 x2 - airOS
Broadcom
Linksys EA6400 - Gateway, QoS
Asus N66U - AP
Netgear WNDR3700v3 - not used
MediaTek
UBNT EdgeRouter X - switch
Sorry if I'm posting on the wrong thread, I'm really new to this sort of forums...
Hi guys, I just bought a TL-WR940N v6 BR and been getting the same 18005 error message... is it the same problem than in v5? Any kind soul to modify the file to be usable in BR? Thanks in advance.
Hello friend, thank you in advance.
But it does not work, the version is BR, in betas there is only US and EU.
ftp://ftp.dd-wrt.com/betas/2019/09-13-2019-r41027/tplink_tl-wr940ndv6/
I flashed them both via TFTP. Everything works, connect to wan, the Wifi network, but does not access the web interface 192.168.1.1, is loading infinitely. SSH and Telnet also do not work.
Sorry if I'm posting on the wrong thread, I'm really new to this sort of forums...
Hi guys, I just bought a TL-WR940N v6 BR and been getting the same 18005 error message... is it the same problem than in v5? Any kind soul to modify the file to be usable in BR? Thanks in advance.
Hello friend, thank you in advance.
But it does not work, the version is BR, in betas there is only US and EU.
ftp://ftp.dd-wrt.com/betas/2019/09-13-2019-r41027/tplink_tl-wr940ndv6/
I flashed them both via TFTP. Everything works, connect to wan, the Wifi network, but does not access the web interface 192.168.1.1, is loading infinitely. SSH and Telnet also do not work.