Debrick Router Twg 870 (Thomson. Inc.) Broadcom 3380

Post new topic   Reply to topic    DD-WRT Forum Forum Index -> Broadcom SoC based Hardware
Author Message
z4t01cH1
DD-WRT Novice


Joined: 26 Jan 2018
Posts: 1

PostPosted: Fri Jan 26, 2018 17:03    Post subject: Debrick Router Twg 870 (Thomson. Inc.) Broadcom 3380 Reply with quote
Hi Guys.

I need help with my router Thomson Twg 870, use the Broadcom 3380 and FLA1 memory is Spansion FL064PIF and RAM is Samsung K4151163QJ. i connect the UART pin and data is show me this:

********************************************************
eCos - hal_diag_init
Init device '/dev/BrcmTelnetIoDriver'
Init device '/dev/ttydiag'
Init tty channel: 810b3d38
Init device '/dev/tty0'
Init tty channel: 810b3d58
Init device '/dev/haldiag'
HAL/diag SERIAL init
Init device '/dev/ser0'
BCM 33XX SERIAL init - dev: 0.2
Set output buffer - buf: 0x812a8570 len: 4096
Set input buffer - buf: 0x812a9570 len: 4096
BCM 33XX SERIAL config

Init device '/dev/ser1'
BCM 33XX SERIAL init - dev: 0.3
Set output buffer - buf: 0x812aa570 len: 4096
Set input buffer - buf: 0x812ab570 len: 4096
BCM 33XX SERIAL config

LsSpiInit 3380
Function: SetHardcodeVendorProfile
Battery Thread Constructor....
Leaving Battery thread constructor....
[Askey Debug]: No VP-24, use the default valus
mtaNvCalcChecksum: checksum= 1273036005
Reading Permanent settings from non-vol...
Checksum for permanent settings: 0x8a973f37
Setting downstream calibration signature to ''
Setting downstream calibration signature to ''

*
*
* One or more of the settings groups was missing, possibly as a result of a code upgrade.
*
*

*
*
* One or more of the settings groups was upgraded.
*
*
Settings were read and verified.


Reading Dynamic settings from non-vol...
Checksum for dynamic settings: 0x5f00baa2
Settings were read and verified.


------------------------------------
Free Pool Manager Configuration
---ChipHalSelectPinMux: Setting pin mux sel 18, word 0, value 2
ChipHalSelectPinMux: Setting pin mux sel 21, word 0, value 1
ChipHalSelectPinMux: Setting pin mux sel 13, word 0, value 0
---------------------------------
Buffer size in Bytes....Creating a new host MSG PROC DQM manager. Instance: 83eaba58, DQM_REGS = b8801800, CTRL_REGS = b8801000
Initializing main MSG_PROC DQM interrupts.
b8801000: 00000000
b8801004: 00000000
b8801008: 00000008
b880100c: 00000000
b8801010: 00000000
b8801014: 00000000
b8801018: 00000000
b880101c: 00000000
........... 2048
Number of TCreating a new host FAP DQM manager. Instance: 83eab9a4
Initializing main FAP DQM interrupts.
b8401000: 00000000
b8401004: 00000000
b8401008: 00000008
b840100c: 00000000
b8401010: 00000000
b8401014: 00000000
b8401018: 00000000
b840101c: 00000000
okens................... 8192
Base Address of FPM Memory ........ 0xb2010200
Base Address of FPM Mem in DDR2.... 0x82e50850

********************************************************

i dont know the next step to install DD WRT firmware, please help me or tell me if is possibly install a new ones.

Thx
Sponsor
Display posts from previous:    Page 1 of 1
Post new topic   Reply to topic    DD-WRT Forum Forum Index -> Broadcom SoC based Hardware All times are GMT

Navigation

 
Jump to:  
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
You can attach files in this forum
You can download files in this forum