New build 09-25-2019-r41134

Post new topic   Reply to topic    DD-WRT Forum Index -> Marvell MVEBU based Hardware (WRT1900AC etc.)
Goto page 1, 2  Next
Author Message
MLandi
DD-WRT Guru


Joined: 04 Dec 2007
Posts: 1008

PostPosted: Wed Sep 25, 2019 16:29    Post subject: New build 09-25-2019-r41134 Reply with quote
ftp://ftp.dd-wrt.com/betas/2019/09-25-2019-r41135/

https://dd-wrt.com/support/other-downloads/?path=betas%2F2019%2F09-25-2019-r41135%2F

NOTE: The folders are labeled as build 41135 but the build identifies as 41134

Smooth upgrade using FF69.0.1x64. No issues, all functions working as expected.

_________________
Netgear R9000
DD-WRT v3.0-r55460 std (03/25/24)
Linux 4.9.337 #715 SMP Mon Mar 25 06:15:53 +07 2024 armv7l
Gateway, AP, DNSMasq, Clock 2000MHz
VAP on wlan1 for internet devices
IPv4 & IPv6 (Prefix Delegation)
Static Leases & DHCP
CloudFlare, no SFE, SmartDNS, no QoS
2.4GHz: Vanilla, Airtime Fairness, NG-Mixed, ACK Timing 3150, WPA2 w/AES & WPA3
5GHz: Vanilla, Airtime Fairness, AC/N Mixed, ACK Timing 3150, WPA2 w/AES & WPA3
2 Netgear AX1800 WiFi Mesh Extenders
Xfinity 1.2Gbps/35Mbps
Sponsor
scar1943
DD-WRT User


Joined: 10 Nov 2018
Posts: 350
Location: South Carolina

PostPosted: Wed Sep 25, 2019 17:32    Post subject: DD-WRT v3.0-r41134 std (09/25/19) Reply with quote
WRT3200ACM V1 r41134 Firefox 69.0.1 (64-bit) webflash

OpenVPN CLIENT works fine (nordvpn server)
5GHz wpa2 CCMP-128 (AES)working fine 20MHz Mixed
2.4GHz wpa2 CCMP-128 (AES)working fine 20MHz Mixed
NAS via USB Samba also working fine
DaveI
DD-WRT User


Joined: 06 Jul 2009
Posts: 333

PostPosted: Wed Sep 25, 2019 18:44    Post subject: Reply with quote
Firmware Version
DD-WRT v3.0-r41134 std (09/25/19)
Kernel Version
Linux 4.9.194 #1313 SMP Wed Sep 25 04:35:31 CEST 2019 armv7l

Both partitions.

_________________
WRT1900ACSv2
illuminati_tri
DD-WRT Novice


Joined: 15 Jul 2019
Posts: 41
Location: Texas

PostPosted: Wed Sep 25, 2019 18:44    Post subject: Reply with quote
Webflash Google Chrome 77.0.3865.90 64-bit (set boot_part)

5GHz, Ch100+UUU, 160MHz, AC/N Mixed
2.4GHz, Ch10+L, 40MHz, N/G Mixed
VAP Guest Network on 2.4GHz; PBR bypasses VPN (SFE enabled)
OpenVPN Client (ExpressVPN)
MAC Whitelist
Static leases

Everything working so far

_________________
Linksys WRT3200ACM r41586
- ExpressVPN | VAP & PBR | Synology NAS
ttowling
DD-WRT User


Joined: 01 Mar 2019
Posts: 130

PostPosted: Thu Sep 26, 2019 8:44    Post subject: Reply with quote
WRT1900ACS V2
Web flash via chrome from build 40134.

Initially appeared stable, but quickly developed serious issues for me.

Flashed with QoS off. On Chrome new QoSs showed as 'undefined' but via Firefox showed all options. Turned QoS back on in Firefox and switched to Cake from Pie.

After around 30 minutes I lost connectivity to internet and thought I was unable to connect to router at all, even by cable, but managed to restore connection, then switched boot partition to revert to 40134.

Question . I am wondering whether a factory reset might fix this and whether the settings being carried over from the older build are causing these issues?
DaveI
DD-WRT User


Joined: 06 Jul 2009
Posts: 333

PostPosted: Thu Sep 26, 2019 9:24    Post subject: Reply with quote
I've been running this build on my WRT1900ACS V2 for about 14 hours now with no such problem but I do not use the QOS as I've found it did not do anything to reduce bufferbloat on my setup and only resulted in consumption of bandwidth...Also sometimes a reboot of both the router and the Gateway device after an upgrade (In my case a Ubiquiti CPE) will avoid the loss of connectivity...At least that's the case for my setup. Flashing with Chrome has also been found to be problematic in the past for some. I did an upgrade from the previous build using the web-flash file.

ttowling wrote:
WRT1900ACS V2
Web flash via chrome from build 40134.

Initially appeared stable, but quickly developed serious issues for me.

Flashed with QoS off. On Chrome new QoSs showed as 'undefined' but via Firefox showed all options. Turned QoS back on in Firefox and switched to Cake from Pie.

After around 30 minutes I lost connectivity to internet and thought I was unable to connect to router at all, even by cable, but managed to restore connection, then switched boot partition to revert to 40134.

Question . I am wondering whether a factory reset might fix this and whether the settings being carried over from the older build are causing these issues?

_________________
WRT1900ACSv2
Monza
DD-WRT User


Joined: 01 Jul 2018
Posts: 438

PostPosted: Thu Sep 26, 2019 12:15    Post subject: Reply with quote
Upgraded WRT1200AC v1 from r41117 to r41134 using Waterfox 56.2.14 (64 bit) running on Linux Mint 19.1 OS.

Successful update and reboot. No reset, nothing disabled prior to update, uptime about 30 mins, wired/wireless connected, vpn up immediately. No drops wired/wireless or OpenVPN. New data added to syslog that I don't recall seeing before.

Kernel Version Linux 4.9.194 #1313 SMP Wed Sep 25 04:35:31 CEST 2019 armv7l

Sep 26 07:52:36 Steve daemon.notice openvpn[1655]: OpenVPN 2.4.7 arm-unknown-linux-gnu [SSL (OpenSSL)] [LZO] [LZ4] [EPOLL] [MH/PKTINFO] [AEAD] built on Sep 25 2019
Sep 26 07:52:36 Steve daemon.notice openvpn[1655]: library versions: OpenSSL 1.1.1c 28 May 2019, LZO 2.09
johnnyNobody999
DD-WRT User


Joined: 10 Jan 2014
Posts: 499

PostPosted: Thu Sep 26, 2019 14:54    Post subject: Reply with quote
I have a similar problem on 2 wrt3200acm routers configured as WDS Stations. The link to the WDS AP via 5 GHz seems to be stable. I still have admin access to all of the routers from a wired connection though. And the 2 GHz radio seems to die even though the status page says it's up. 2 GHz clients that were attached drop off. Rebooting the WDS Station routers restores service. I tried a factory restore on one of the routers and manually reconfigured it but the problem persists.

ttowling wrote:
WRT1900ACS V2
Web flash via chrome from build 40134.

Initially appeared stable, but quickly developed serious issues for me.

Flashed with QoS off. On Chrome new QoSs showed as 'undefined' but via Firefox showed all options. Turned QoS back on in Firefox and switched to Cake from Pie.

After around 30 minutes I lost connectivity to internet and thought I was unable to connect to router at all, even by cable, but managed to restore connection, then switched boot partition to revert to 40134.

Question . I am wondering whether a factory reset might fix this and whether the settings being carried over from the older build are causing these issues?
M
DD-WRT User


Joined: 29 Dec 2012
Posts: 183

PostPosted: Thu Sep 26, 2019 17:06    Post subject: Reply with quote
This problem also happen this build on 16/11/17.

Could you show the warning message from syslog page for the administrator information please? (http://192.168.1.1/Syslog.asp)

I fear to upgrade about WRT1900ACS V2. It is unstable.

Thanks



ttowling wrote:
WRT1900ACS V2
Web flash via chrome from build 40134.

Initially appeared stable, but quickly developed serious issues for me.

Flashed with QoS off. On Chrome new QoSs showed as 'undefined' but via Firefox showed all options. Turned QoS back on in Firefox and switched to Cake from Pie.

After around 30 minutes I lost connectivity to internet and thought I was unable to connect to router at all, even by cable, but managed to restore connection, then switched boot partition to revert to 40134.

Question . I am wondering whether a factory reset might fix this and whether the settings being carried over from the older build are causing these issues?
scar1943
DD-WRT User


Joined: 10 Nov 2018
Posts: 350
Location: South Carolina

PostPosted: Thu Sep 26, 2019 17:08    Post subject: WRT3200ACM V1 - r41134 Reply with quote
Slightly skeered. lol

24 hours, no issues yet, however, I'm not using some of the options that folks having trouble with are using.

VPN client, USB Samba, narrow 20MHz G and N on both bands, and a full array of wired clients (16 wired and wireless clients). No problems seen yet.
M
DD-WRT User


Joined: 29 Dec 2012
Posts: 183

PostPosted: Thu Sep 26, 2019 17:23    Post subject: Reply with quote
Dear All

I am a dd-wrt user.
I think my message may make your inconvenience.

I recommend all of us (including me) report the operation of our routers.

If we report the dd-wrt build (Normal Operation or Abnormal Status)
Please also highlight the warning message from System Logs. The situations may make Programmer debug easily for the next build.

For example

1. Enable Klogd and Syslogd from http://192.168.1.1/Services.asp

2. Collect the information (Yellow Colour and Red Colour) message from http://192.168.1.1/Syslog.asp when boot.

3. Describe the symptom with 3W and 1H
What, Why, When & How

4. Print Screen the Config if possible

Many Thanks

M[/u]
ttowling
DD-WRT User


Joined: 01 Mar 2019
Posts: 130

PostPosted: Thu Sep 26, 2019 18:13    Post subject: Reply with quote
M wrote:
Dear All

I am a dd-wrt user.
I think my message may make your inconvenience.

I recommend all of us (including me) report the operation of our routers.

If we report the dd-wrt build (Normal Operation or Abnormal Status)
Please also highlight the warning message from System Logs. The situations may make Programmer debug easily for the next build.

For example

1. Enable Klogd and Syslogd from http://192.168.1.1/Services.asp

2. Collect the information (Yellow Colour and Red Colour) message from http://192.168.1.1/Syslog.asp when boot.

3. Describe the symptom with 3W and 1H
What, Why, When & How

4. Print Screen the Config if possible

Many Thanks

M[/u]


I was too busy scrambling to switch partitions while it would let me.
I was in a really dark place when it became unresponsive.
CantRepeat
DD-WRT User


Joined: 18 Oct 2017
Posts: 153

PostPosted: Thu Sep 26, 2019 22:51    Post subject: Re: New build 09-25-2019-r41134 Reply with quote
MLandi wrote:
ftp://ftp.dd-wrt.com/betas/2019/09-25-2019-r41135/

https://dd-wrt.com/support/other-downloads/?path=betas%2F2019%2F09-25-2019-r41135%2F

NOTE: The folders are labeled as build 41135 but the build identifies as 41134

Smooth upgrade using FF69.0.1x64. No issues, all functions working as expected.


I was wondering why I couldn't find the 41134 build and why no one posted the 41135 build. lol

_________________
-Tim
M
DD-WRT User


Joined: 29 Dec 2012
Posts: 183

PostPosted: Fri Sep 27, 2019 4:13    Post subject: WRT1900ACSV2 (T_T) Reply with quote
On my last post, I also mention that WRT1900ACSV2 DD-WRT Build is unstable since November 2017. The CPU Temperature is too high to 83.2C. It causes the CPU unstable. I know your case because I also this issues in 2017 Build but if you use VNC to remote the desktop or laptop. It can remote but you cannot browse the internet. After that, You will discover that is a DNS issues from the DD-WRT. AC(S)V2 means slow.

The wifi signal also cause by CPU High Temperature.

If you test, you will find changing Clone WAN MAC from MAC Address Clone, we must change vendor Mac Address. If not, the ISP will not provide a new Dynamic IP Address or no update.

The other issues are that DDNS Issues (http://192.168.1.1/DDNS.asp)does not work every reboot.


The reboot router button and schedule router processes are a little different. It is different with other type of routers. The reboot router button does not work the apply setting when you update some configurations. Schedule reboot will work since 2017.

We need to cut off the power and restart the router. After that it will work.






ttowling wrote:
M wrote:
Dear All

I am a dd-wrt user.
I think my message may make your inconvenience.

I recommend all of us (including me) report the operation of our routers.

If we report the dd-wrt build (Normal Operation or Abnormal Status)
Please also highlight the warning message from System Logs. The situations may make Programmer debug easily for the next build.

For example

1. Enable Klogd and Syslogd from http://192.168.1.1/Services.asp

2. Collect the information (Yellow Colour and Red Colour) message from http://192.168.1.1/Syslog.asp when boot.

3. Describe the symptom with 3W and 1H
What, Why, When & How

4. Print Screen the Config if possible

Many Thanks

M[/u]


I was too busy scrambling to switch partitions while it would let me.
I was in a really dark place when it became unresponsive.
M
DD-WRT User


Joined: 29 Dec 2012
Posts: 183

PostPosted: Fri Sep 27, 2019 4:27    Post subject: Reply with quote
I recommend you downgrade the build to 2016 or 2017 version

ttowling wrote:
M wrote:
Dear All

I am a dd-wrt user.
I think my message may make your inconvenience.

I recommend all of us (including me) report the operation of our routers.

If we report the dd-wrt build (Normal Operation or Abnormal Status)
Please also highlight the warning message from System Logs. The situations may make Programmer debug easily for the next build.

For example

1. Enable Klogd and Syslogd from http://192.168.1.1/Services.asp

2. Collect the information (Yellow Colour and Red Colour) message from http://192.168.1.1/Syslog.asp when boot.

3. Describe the symptom with 3W and 1H
What, Why, When & How

4. Print Screen the Config if possible

Many Thanks

M[/u]


I was too busy scrambling to switch partitions while it would let me.
I was in a really dark place when it became unresponsive.
Goto page 1, 2  Next Display posts from previous:    Page 1 of 2
Post new topic   Reply to topic    DD-WRT Forum Index -> Marvell MVEBU based Hardware (WRT1900AC etc.) All times are GMT

Navigation

 
Jump to:  
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
You cannot attach files in this forum
You cannot download files in this forum