Posted: Sat Oct 28, 2017 6:16 Post subject: Linksys E900
Router/Version: Linksys E900 V1
Firmware: DD-WRT v3.0-r33607 mega (10/25/17)
Kernel: Linux 3.10.107 #16438 Wed Oct 25 10:47:53 CEST 2017 mips
Previous: k26 33555
Mode/Status: Auto Config DHCP, Wifi AP
Reset: yes, during flash
Issues/Errors: None so far.I Don't use VLANs or USB.
EDIT: formatting.
Last edited by Harshwardhan on Sat Oct 28, 2017 8:24; edited 2 times in total
Router: Netgear WNDR3400v1
Firmware: dd-wrt.v24-33607_NEWD-2_K3.x_mega-nv64k.bin
Kernel: Linux 3.10.107 #16448
Previous: dd-wrt.v24-33555_NEWD-2_K3.x_mega-nv64k.bin
Status: No connectivity between wl0 and wl1
Reset: No
Errors: I thought everything was OK until I just tried scanning using my lone item on the 2.4 GHz band. The printer/scanner connects to the 2.4 wireless but cannot be pinged from any of my hosts on the 5 GHz including the router.
Reverted to 33555 and it works fine.
scootcha, check to see if the radios are in different vlans
tried 30/30/30 reset did not make any difference. Radio shows as disabled.
Attempted to downgrade to build 33555 K3.0 and vlan setups became corrupted and the LAN interfaces stopped working however the wifi radio did start working. Had to revert to build 33555 K2.6 in order for the vlans to be properly configured and the radio and LAN ports to work.
I believe the K3.X 33555 build would work if webflashed with NO RESET from K2.6 build 33555 BUT if the router were 30/30/30ed with a K3.x build on it, it would not properly setup the VLAN.
Attempted to update to build 33607 mini K2.6 on this router from build 33555 mini K2.6 - that failed initially, wifi radio was not on channel selection is set to Auto and does not allow changing. Reverted to a much older build 25628 which also displayed the same issue with the radio, did a 30/30/30 reset, the radio then came back, then updated to build 33607 K2.6 mini and everything worked.
Last edited by tedm on Sat Oct 28, 2017 18:44; edited 2 times in total
ASUS AC66U. Upgraded from 33006 to 33607. Appears to have WiFi issues on 5GHz band. My Nexus 6 (phone) repeatedly connects and disconnects. Confirmed on both the phone and the router SysInfo screen. Power cycling the router and phone have no affect. So far my Chromecasts appear to be working okay but none of the other phones are showing up on the SysInfo screen, either.
Edit - rolled back to 33525, it appears to work a bit better.
Router/Version: Archer C9 v1
Firmware: DD-WRT v3.0-r33607 std (10/25/17)
Kernel: Linux 4.4.94 #2179 SMP Wed Oct 25 06:24:25 CEST 2017 armv7l
Previous: r32597
Mode/Status: 2.4 AP, 5 Client
Reset: no
Issues/Errors: None so far. I use 5 GHz to connect to WISP and then broadcast my own 2.4 GHz network.
Attempted to update to 33607 K3.x mega and was UNABLE to do so, the router DID NOT flash it (flash aborted by the router)
30/30/30 reset on the previous build 33555 mega K3.x change the VLAN assignment making the Ethernet ports unusable. I was able to attach to the dd-wrt SSID and put the VLAN assignment back then save it and power-cycle the router to get it back working again.
Problems were similar as with my Linksys E1500 v1 router.
mini lacks IPv6 support, but there is no mini in the K3.x build.
Last edited by tedm on Sat Oct 28, 2017 18:11; edited 1 time in total
scootcha, check to see if the radios are in different vlans
My config is rather vanilla, I have never used wireless virtual interfaces in the past and they are not configured now. I can't quite tell from your statement if you think implementing them would help alleviate this issue or I should continue to avoid them.
Router/Version: Linksys E3000
Firmware: DD-WRT v3.0-r33607 mega (10/25/17)
Kernel: Linux 2.6.24.111 #32965 Wed Oct 25 00:56:34 CEST 2017 mips
Previous: k3.x 23919
Mode/Status: Client bridge
Reset: 30-30-30 before and after flash.
Issues/Errors: Seems to work fine (5ghz only, haven't tried 2.4)
Other: In between the two builds above, I briefly tried the k3.x version of 33607. Because the WebGUI (still) lacks TLS support, I loaded the k2.6 version.
Posted: Sat Oct 28, 2017 20:37 Post subject: ASUS RT-AC68U & Linksys E2000
Asus RT-AC68U
Firmware: DD-WRT v3.0-r33607 std (10/25/17) - (previous r33555)
Kernel: Linux 4.4.94 #2177 SMP Tue Oct 24 06:50:06 CEST 2017 armv7l
5Ghz (Mixed) with 80Mhz channel width: Ok
SSH: Ok
Telnet: Disabled but tested to work
Site Survey: Ok
Wi-viz Survey 2.4Ghz & 5Ghz: Ok
Reset: No
Status: Ok*
Uptime: 3 days, 1:49
CPU Temperature: CPU 68.0 °C / WL0 45.0 °C / WL1 45.5 °C
2 x E2000
Firmware: DD-WRT v3.0-r33607 mega (10/25/17) - (previous r33555)
Kernel: Linux 3.10.107 #16438 Wed Oct 25 10:47:53 CEST 2017 mips
2.4Ghz (NG-mixed) with 40Mhz channel width: Ok
SSH: Ok
Telnet: Disabled but tested to work
Site Survey: Ok
Wi-viz Survey 2.4Ghz: Ok
Reset: No
Status: Ok*
Uptime: 1 day, 1:21
CPU Temperature: WL0 53.8 °C
*Experiencing dropouts on both 5 and 2.4 GHz
All devices working as AP's each with individual 1Gb wired connections to main firewall
