I think just bricked 1900ac

Post new topic   Reply to topic    DD-WRT Forum Forum Index -> Marvell MVEBU based Hardware (WRT1900AC etc.)
Author Message
e123enitan
DD-WRT Novice


Joined: 13 Mar 2017
Posts: 46

PostPosted: Sun Feb 25, 2018 23:09    Post subject: I think just bricked 1900ac Reply with quote
Help anyone I just updated 1900ac with wrong mode 1900acs v1, now I can't get into the router any longer. The router power just flashing but I can't get into the router.

Appreciate any suggestions
Sponsor
LookingForMyMojo
DD-WRT Guru


Joined: 29 Aug 2014
Posts: 693

PostPosted: Sun Feb 25, 2018 23:25    Post subject: Re: I think just bricked 1900ac Reply with quote
e123enitan wrote:
Help anyone I just updated 1900ac with wrong mode 1900acs v1, now I can't get into the router any longer. The router power just flashing but I can't get into the router.

Appreciate any suggestions


use the on-off method to flip it to the other partition

_________________
My "WRT" rant, and why I have gone ddwrt on x86, no more consumer routers. ( ac86u as access points & bridges )

https://www.dd-wrt.com/phpBB2/viewtopic.php?t=312142&highlight=ac86u
e123enitan
DD-WRT Novice


Joined: 13 Mar 2017
Posts: 46

PostPosted: Sun Feb 25, 2018 23:31    Post subject: Re: I think just bricked 1900ac Reply with quote
LookingForMyMojo wrote:
e123enitan wrote:
Help anyone I just updated 1900ac with wrong mode 1900acs v1, now I can't get into the router any longer. The router power just flashing but I can't get into the router.

Appreciate any suggestions


use the on-off method to flip it to the other partition


Pls I dont understand what you mean by on-off, appreciate a simple guide
Thanks
LookingForMyMojo
DD-WRT Guru


Joined: 29 Aug 2014
Posts: 693

PostPosted: Sun Feb 25, 2018 23:33    Post subject: Re: I think just bricked 1900ac Reply with quote
e123enitan wrote:
LookingForMyMojo wrote:
e123enitan wrote:
Help anyone I just updated 1900ac with wrong mode 1900acs v1, now I can't get into the router any longer. The router power just flashing but I can't get into the router.

Appreciate any suggestions


use the on-off method to flip it to the other partition


Pls I dont understand what you mean by on-off, appreciate a simple guide
Thanks


I am not intending to be sarcastic.

For your own good. Read the info below before doing anything else

https://www.dd-wrt.com/phpBB2/viewtopic.php?t=311117

_________________
My "WRT" rant, and why I have gone ddwrt on x86, no more consumer routers. ( ac86u as access points & bridges )

https://www.dd-wrt.com/phpBB2/viewtopic.php?t=312142&highlight=ac86u
myersw
DD-WRT Guru


Joined: 13 Jun 2006
Posts: 1609
Location: SE Michigan USA

PostPosted: Mon Feb 26, 2018 1:13    Post subject: Reply with quote
Hands off the wrt until you understand the wrt. Read the threads in my sig and then you will know what is meant by the on off sequence, plus other ways of switching partitions and lots of other good needed info.
--bill

_________________
Unifi Security Gateway: Unifi Firmware
Netgear r7800: Voxel Firmware
Modem:Netgear CM500V voice and Data.
ISP:Comcast
tutorial for flashing "WRT" series:
http://www.dd-wrt.com/phpBB2/viewtopic.php?t=287813
DD-WRT Installation, Upgrade & Basic Setup–Cliff Notes:
http://www.dd-wrt.com/phpBB2/viewtopic.php?t=311117
Kong DD-WRT Config Tutorial:
http://www.instructables.com/id/Install-and-Configure-a-DD-WRT-Kong-Router/
I tried to be normal once. Worst 2 minutes ever.
e123enitan
DD-WRT Novice


Joined: 13 Mar 2017
Posts: 46

PostPosted: Mon Feb 26, 2018 1:39    Post subject: Reply with quote
myersw wrote:
Hands off the wrt until you understand the wrt. Read the threads in my sig and then you will know what is meant by the on off sequence, plus other ways of switching partitions and lots of other good needed info.
--bill


Guys Thanks, for some no reason the system came back, I just left it turned of for about half hr, just about to putty into it, then I noticed that both power and internet light was solid, then I logged into it and I was successful. I have reflash with right and restored the back up and everything is back to normal.
Thanks again.
Display posts from previous:    Page 1 of 1
Post new topic   Reply to topic    DD-WRT Forum Forum Index -> Marvell MVEBU based Hardware (WRT1900AC etc.) All times are GMT

Navigation

 
Jump to:  
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
You cannot attach files in this forum
You cannot download files in this forum