WAN VLAN Tagging NIGHTMARE

Post new topic   Reply to topic    DD-WRT Forum Index -> Marvell MVEBU based Hardware (WRT1900AC etc.)
View previous topic :: View next topic  
Author Message
naps1saps
DD-WRT Novice


Joined: 16 Dec 2016
Posts: 14
PostPosted: Sun Aug 13, 2017 9:07    Post subject: WAN VLAN Tagging NIGHTMARE Reply with quote
I just had Centurylink installed with the ONT and it works great... just not with my WRT1200AC v1 router on DDWRT. I can get connected with PPPoE on the stock firmware but I cannot get it connected with DDWRT.

I obviously added my username and password.
I added a VLAN tag e0 -> vlan 201
Changed the WAN interface to e0.201

Rebooted everything and waited. Nothing.
WAN IP is 0.0.0.0

Am I doing something wrong here???
PLEASE HELP!!! Shocked
Back to top View user's profile Send private message
Sponsor
Per Yngve Berg
DD-WRT Guru


Joined: 13 Aug 2013
Posts: 6868
Location: Romerike, Norway
PostPosted: Sun Aug 13, 2017 10:03    Post subject: Reply with quote
Search this forum on how to use SWCONFIG to configure VLAN.
Back to top View user's profile Send private message
naps1saps
DD-WRT Novice


Joined: 16 Dec 2016
Posts: 14
PostPosted: Sun Aug 13, 2017 21:41    Post subject: Reply with quote
I tried out OpenWRT last night and if I can get the same functions working VPN and bandwidth tracking I like the interface better.

Is there any WAN to LAN performance difference between ddwrt and openwrt? I have gigabit so it matters.
Back to top View user's profile Send private message
naps1saps
DD-WRT Novice


Joined: 16 Dec 2016
Posts: 14
PostPosted: Mon Aug 14, 2017 2:46    Post subject: Reply with quote
Per Yngve Berg wrote:
Search this forum on how to use SWCONFIG to configure VLAN.


Changed my mind openwrt is not working for me. I'm having trouble finding SWCONFIG information. I'm not sure how to configure the code. I found this site:
http://trac.gateworks.com/wiki/OpenWrt/swconfig

Can someone help with configuring WAN for vlan tagging 201 using swconfig?
Back to top View user's profile Send private message
naps1saps
DD-WRT Novice


Joined: 16 Dec 2016
Posts: 14
PostPosted: Mon Aug 14, 2017 4:19    Post subject: Reply with quote
Found some more information and tried some code but the router just locks up requiring a power cycle.

Code:
swconfig dev eth0 set reset
swconfig dev eth0 set enable_vlan1
swconfig dev eth0 vlan 1 set vid 201
swconfig dev eth0 vlan 1 set ports '0 4t'
swconfig dev eth0 set apply


Any advice?
Back to top View user's profile Send private message
Per Yngve Berg
DD-WRT Guru


Joined: 13 Aug 2013
Posts: 6868
Location: Romerike, Norway
PostPosted: Mon Aug 14, 2017 8:30    Post subject: Reply with quote
You have reset the switch, but you have not configured a new LAN.

Isn't the WAN on VLAN2?
Back to top View user's profile Send private message
naps1saps
DD-WRT Novice


Joined: 16 Dec 2016
Posts: 14
PostPosted: Mon Aug 14, 2017 14:49    Post subject: Reply with quote
To be honest I have no idea but I will try that.
Back to top View user's profile Send private message
Gigabitten
DD-WRT Novice


Joined: 02 Jun 2017
Posts: 43
PostPosted: Wed Aug 23, 2017 18:33    Post subject: Reply with quote
VLAN/ tagging and swconfig not fully functional with DD-WRT and Marvell chipsets yet.
_________________
Linksys WRT3200ACM
Build: B.S.'s DD-WRT v3.0-r32597 std (07/08/17)

Help me with my VLANING problem:
https://www.dd-wrt.com/phpBB2/viewtopic.php?t=309654
Back to top View user's profile Send private message
naps1saps
DD-WRT Novice


Joined: 16 Dec 2016
Posts: 14
PostPosted: Tue May 15, 2018 21:59    Post subject: Reply with quote
So I ended up switching over to OpenWRT and have been using it a while but only on an older firmware, the new one does not work. I'm now needing the new one to work for reasons. So I'm going to be posting over there for some help Smile
Back to top View user's profile Send private message
Display posts from previous:    Page 1 of 1
Post new topic   Reply to topic    DD-WRT Forum Index -> Marvell MVEBU based Hardware (WRT1900AC etc.) All times are GMT

Navigation

 
Jump to:  
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
You cannot attach files in this forum
You cannot download files in this forum