New Kong's Test build DD-WRT v3.0-r36840M kongac (09/03/18)

Post new topic   Reply to topic    DD-WRT Forum Forum Index -> Broadcom SoC based Hardware
Goto page 1, 2, 3  Next
Author Message
egc
DD-WRT Guru


Joined: 18 Mar 2014
Posts: 5544
Location: Netherlands

PostPosted: Tue Sep 04, 2018 10:57    Post subject: New Kong's Test build DD-WRT v3.0-r36840M kongac (09/03/18) Reply with quote
Kong's DD-WRT test build v3.0-r36840M kongac (09/03/2018)) has been released: http://desipro.de/ddwrt/K3-AC-Arm/TEST/

Support for R6400v2 (with different boardid's) and R6700v3 added.

Your reports for Broadcom units are greatly appreciated !
Router:
Firmware:
Kernel:
Status:
Reset:
Errors:


This build thread is for reporting successes and problem with loading this experimental test build. This is important info for developers and users. Always state your hardware and SPECIFIC build (e.g. 29440_NEWD-2_K2.6_mega-nv64k.bin). Do not ask questions about your specific router or how to configure it in this thread; create your own thread to discuss any specific problems you have or need resolved. Please also do not respond to such questions. This thread is to report info, not to seek it. Posts that do not add to understanding this build will be deleted. Make sure you know how to flash properly and the risk before using this build. It is important to adhere to these requirements, to keep this thread from becoming impossibly long and useless. If you don't know what build to flash and how to flash properly and have a means of recovery if things should go wrong, do NOT flash this experimental test build.

_________________
Routers:Netgear R7800, Netgear R6400v1, Netgear R6400v2, Linksys EA6900 (XvortexCFE), Linksys E2000 (converted WRT320N), WRT54GS v1.
Install guide Linksys EA6900: http://www.dd-wrt.com/phpBB2/viewtopic.php?t=291230
OpenVPN Policy Based Routing guide: https://forum.dd-wrt.com/phpBB2/viewtopic.php?t=321686
Install guide R6400v2:http://forum.dd-wrt.com/phpBB2/viewtopic.php?t=316399
OpenVPN Server Setup:https://forum.dd-wrt.com/phpBB2/viewtopic.php?t=318795
Install guide R7800: https://forum.dd-wrt.com/phpBB2/viewtopic.php?t=320614
Wireguard server setup guide:https://forum.dd-wrt.com/phpBB2/viewtopic.php?p=1183135
Wireguard client setup guide:https://forum.dd-wrt.com/phpBB2/viewtopic.php?t=324624
Wireguard Advanced setup guide:https://forum.dd-wrt.com/phpBB2/viewtopic.php?t=324787
Sponsor
egc
DD-WRT Guru


Joined: 18 Mar 2014
Posts: 5544
Location: Netherlands

PostPosted: Tue Sep 04, 2018 11:06    Post subject: Reply with quote
Router Model: Netgear R6400 v2 (boardid: U12H332T30_NETGEAR)

Firmware Version: DD-WRT v3.0-r36840M kongac (09/03/2018)
Kernel Version: Linux 4.4.153 #598 SMP Mon Sep 3 22:38:12 CEST 2018 armv7

Upgraded: from v3.0-r36820M kongac (09/01/2018)
Reset: No

Configuration: Repeater bridge and VAP on 2.4 GHz, 5 Ghz also working.

Status: Up and stable for 1 h, excellent wireless speed and range, Router is recognised as R 6400v2
Errors: none so far

Thanks BrainSlayer and special thanks to Kong for his support!!

_________________
Routers:Netgear R7800, Netgear R6400v1, Netgear R6400v2, Linksys EA6900 (XvortexCFE), Linksys E2000 (converted WRT320N), WRT54GS v1.
Install guide Linksys EA6900: http://www.dd-wrt.com/phpBB2/viewtopic.php?t=291230
OpenVPN Policy Based Routing guide: https://forum.dd-wrt.com/phpBB2/viewtopic.php?t=321686
Install guide R6400v2:http://forum.dd-wrt.com/phpBB2/viewtopic.php?t=316399
OpenVPN Server Setup:https://forum.dd-wrt.com/phpBB2/viewtopic.php?t=318795
Install guide R7800: https://forum.dd-wrt.com/phpBB2/viewtopic.php?t=320614
Wireguard server setup guide:https://forum.dd-wrt.com/phpBB2/viewtopic.php?p=1183135
Wireguard client setup guide:https://forum.dd-wrt.com/phpBB2/viewtopic.php?t=324624
Wireguard Advanced setup guide:https://forum.dd-wrt.com/phpBB2/viewtopic.php?t=324787
Bernadoe
DD-WRT User


Joined: 03 Dec 2014
Posts: 206

PostPosted: Tue Sep 04, 2018 13:25    Post subject: Reply with quote
Router: Netgear R7000
Firmware: DD-WRT v3.0-r36840M kongac (09/03/2018)
Kernel Version : Linux 4.4.153 #598 SMP Mon Sep 3 22:38:12 CEST 2018 armv7l
Status: Working
Reset: No
Previous: 36820M
Errors: No

Temperatures : CPU 54.7 °C / WL0 48.0 °C / WL1 50.0 °C

Working very well :
Router mode : DHCP
SFE Enable
STP Enable
DNSMasq
Encrypt DNS
Cache DNSSEC data
Validate DNS Replies (DNSSEC)
Local DNS
No DNS Rebind
Query DNS in Strict Order
Usb
Nas, Samba, JFFS2, MiniDLNA
wl0, wl1
Vpn (OpenVPN Client)

Kong and BS: Thanks for all your good work!

without VPN



with VPN
jheide44
DD-WRT Guru


Joined: 03 Sep 2013
Posts: 729

PostPosted: Tue Sep 04, 2018 14:47    Post subject: Reply with quote
Netgear R6400v1
Kong PTB ????? file dated 7/30/18 (i think?) --> Kong PTB 36840 file dated 09/03/2018 )

**Dirty Flash -- NO RESET**

Firmware Version: DD-WRT v3.0-r36840M kongac (09/03/18 )
Kernel Version: Linux 4.4.153 #598 SMP Mon Sep 3 22:38:12 CEST 2018 armv7l

File: http://www.desipro.de/ddwrt/ or http://ddwrt-kong.clonevince.fr/
File Name: dd-wrt.v24-K3_AC_ARM_STD_128K.bin
MD5: N/A, used ddup from CLI


DDNS -- OK (custom for dnsomatic)
SSH Tunneling -- OK (update to 2048 bit key!)
**note: Flashed from the far side of an SSH tunnel. Initial testing performed based on 30 minutes observations, I will update if anything above is not accurate**
DDNS -- OK (custom for dnsomatic)
RDP session via SSH Tunneling -- OK
OpenDNS Content Filtering -- OK
SAMBA -- OK, 2tb public NAS no security
MiniDLNA -- NOT TESTED THIS TIME



ddup command love notes:

I forget what version I was on 7/30/18 if i recall...
ddup --flash-latest

*** REBOOT HERE ***

login as: root
DD-WRT v3.0-r36840M kongac (c) 2018 NewMedia-NET GmbH
Release: 09/03/18
Authenticating with public key "rsa-key-20180327"
Passphrase for key "rsa-key-20180327":


BusyBox v1.29.2 (2018-09-03 22:43:19 CEST) built-in shell (ash)

root@DD-WRT:~# clear
root@DD-WRT:~#

_________________
reenignE esreveR
Resistance is NOT futile... It's Voltage divided by Current!

[size=9]
_.-:Curently Deployed Devices:-._
Loc_1.0: R6400 -- Kong PTB 35550M 03-28-2018
Loc_2.0: R6300v2 -- Kong PTB 35550M 03-28-2018
Loc_3.0: R6300v2 -- Kong PTB 35030M 02-19-2018
Loc_4.0: R6300v2 -- Kong PTB 28600M 12-31-2015 (Radios OFF) & 5 Ubiquity UniFi APs
Loc_4.1: E4200 -- BrainSlayer K2.6 30880
Others: too many others to list

UNofficial Repo Kong's old builds HERE.

R7000 (& similar HW) Tips/Tricks HERE.

Assumptions:
1. Everyone on the forum has read the relevant forum section announcements.
2. For Broadcom section we have ALL at least tried to understand the "Peacock" thread,
HERE
eywong
DD-WRT User


Joined: 21 Jul 2010
Posts: 120
Location: USA

PostPosted: Tue Sep 04, 2018 17:17    Post subject: Asus RT-AC68U A1 Reply with quote
Router: Asus RT-AC68U (H/W Ver: A1)
Firmware: DD-WRT v3.0-r36840M kongac (09/03/18)
Previous: DD-WRT v3.0-r36820M kongac (09/01/18)
Kernel: Linux 4.4.153 #598 SMP Mon Sep 3 22:38:12 CEST 2018 armv7l
Previous: Linux 4.4.153 #595 SMP Sat Sep 1 19:15:55 CEST 2018 armv7l
Status: ok
Reset: no (ddup --flash-latest)
Errors: no
Uptime: 1:00

wl0: AP / NG-Mixed / Ch 11
Channel Width: 20 MHz
wl1: AP / AC/N-Mixed / Ch 52 + 54
Channel Width: Wide VHT80 (80 MHz)
Extension Channel: lower lower
DHCP Server: Enabled - Running
Static Leases: 4 hardwired NAS, 1 wireless printer
NTP Client: Enable
Server IP/Name: us.pool.ntp.org
IPv6: Disable
Xeon2k8
DD-WRT Guru


Joined: 11 Feb 2016
Posts: 1321

PostPosted: Tue Sep 04, 2018 17:53    Post subject: Reply with quote
Router: R6400v2 (boardID ending in 30)
Firmware: DD-WRT v3.0-r36840M kongac (09/03/18 )
Kernel: Linux 4.4.153 #598 SMP Mon Sep 3 22:38:12 CEST 2018 armv7l
Status: Good
Reset: Yes
Errors: None

Comments: Flashed from stock. Usual steps, restore to factory, reboot, flash through LAN cable, erase nvram and reboot.

Everything smooth and perfect. If I have issues will update the thread.

_________________
R6400v2 (boardID:30) - Kong 36480 running since 03/09/18 - (AP - DNSMasq - AdBlocking - QoS)
R7800 - BS 31924 running since 05/26/17 - (AP - OpenVPN Client - DNSMasq - AdBlocking - QoS)
R7000 - BS 30771 running since 12/16/16 - (AP - NAS - FTP - SMB - OpenVPN Server - Transmission - DDNS - DNSMasq - AdBlocking - QoS)
R6250 - BS 29193 running since 03/20/16 - (AP - NAS - FTP - SMB - DNSMasq - AdBlocking)
bushant
DD-WRT Guru


Joined: 18 Nov 2015
Posts: 1380

PostPosted: Tue Sep 04, 2018 22:40    Post subject: Reply with quote
Router Name6200v2 What it is
Router Model Netgear R6250 What it ain't
Firmware Version DD-WRT v3.0-r36840M kongac 09/03/18
Kernel Version Linux 4.4.153 #598 SMP Mon Sep 3
Previous 36820
no reset
no errors
Working

I can now confirm the only method of upgrading/downgrading this unsupported unit:
You have to soft brick it. Try to upgrade/downgrade via WebGUI or ddup will do it.
Then tftp with 24170-dd-wrt-K3_R6200V2_7-Aug-2014.chk. Timing is no issue.
Then install dd-wrt.v24-K3_AC_ARM_STD.bin via WebGUI.
So now it is on 36840

GW AP
VAP on both radios
1TB HDD serving minidlna
usb entware YAMon3 nano others
ovpn client
proftp

EDIT: Have not tried upgrade via CLI. Next time.
mac913
DD-WRT Guru


Joined: 02 May 2008
Posts: 1519
Location: Canada

PostPosted: Wed Sep 05, 2018 4:45    Post subject: Reply with quote
Router: Gateway R7000 (WiFi Disabled)
Firmware: DD-WRT v3.0-r36840M kongac (09/03/2018)
Kernel Version : Linux 4.4.153 #598 SMP Mon Sep 3 22:38:12 CEST 2018 armv7l
Status: Working
Reset: No
Previous: 36410M
Errors: No

Router: WiFi R7000 (2.4Ghz + 2 VAPs & 5Ghz +VAP)
Firmware: DD-WRT v3.0-r36840M kongac (09/03/2018)
Kernel Version : Linux 4.4.153 #598 SMP Mon Sep 3 22:38:12 CEST 2018 armv7l
Status: Gone Back to Spare R7000 with Working 35550M
Reset: No
Previous: 36410M
Errors: Can Not Connect to VAP on 5Ghz (WL1.1)

_________________
Home Network on Telus PureFibre - 10GbE Copper Backbone
2x R7800 - Gateway WiFi 3xWireGuard - DDWRT r43290 Std
WHR-HP-G54 - Internal Routing - DDWRT r35531 std-special
2x E3000 - Gateway Wired IPTV - DDWRT r35531 Mega
E3000 - TRAVEL Wireless Client WireGuard(+25Mbit/s) - DDWRT r43290 Mega

Off Site 1

R7000 - Gateway, WiFi & WireGuard - DDWRT r43217 Std
WRT610Nv1 - Client Bridge - DDWRT r33679 Mega K2.4

Off Site 2

R7000 - Gateway & WiFi - DDWRT r43217 Std
E2000 - Wired PVR Blocker - DDWRT r35531


YAMon 3.4.6 | DNSCrypt-Proxy V2
egc
DD-WRT Guru


Joined: 18 Mar 2014
Posts: 5544
Location: Netherlands

PostPosted: Wed Sep 05, 2018 11:41    Post subject: Reply with quote
Router Model: Linksys EA6900 (XVortex CFE)

Firmware Version: DD-WRT v3.0-r36840M kongac (09/03/2018)
Kernel Version: Linux 4.4.153 #598 SMP Mon Sep 3 22:38:12 CEST 2018 armv7l

Upgraded: from 36820M via telnet (upgrade via WebGui or DDUP not possible, due to XVortex CFE)
Reset: No, not this time

Configuration: Gateway, AP, DHCP server, 2,4GHz wireless running, 5GHz running, some static leases.
Unbridged VAP on 5 GHz. working!
NVRAM size just below 32K (NVRAM size should not be a problem with the Xvortex CFE)

Status: Up and stable for 2 h, excellent wireless speed and range,
Errors: none so far

Thanks Kong and BrainSlayer!!

_________________
Routers:Netgear R7800, Netgear R6400v1, Netgear R6400v2, Linksys EA6900 (XvortexCFE), Linksys E2000 (converted WRT320N), WRT54GS v1.
Install guide Linksys EA6900: http://www.dd-wrt.com/phpBB2/viewtopic.php?t=291230
OpenVPN Policy Based Routing guide: https://forum.dd-wrt.com/phpBB2/viewtopic.php?t=321686
Install guide R6400v2:http://forum.dd-wrt.com/phpBB2/viewtopic.php?t=316399
OpenVPN Server Setup:https://forum.dd-wrt.com/phpBB2/viewtopic.php?t=318795
Install guide R7800: https://forum.dd-wrt.com/phpBB2/viewtopic.php?t=320614
Wireguard server setup guide:https://forum.dd-wrt.com/phpBB2/viewtopic.php?p=1183135
Wireguard client setup guide:https://forum.dd-wrt.com/phpBB2/viewtopic.php?t=324624
Wireguard Advanced setup guide:https://forum.dd-wrt.com/phpBB2/viewtopic.php?t=324787
mac913
DD-WRT Guru


Joined: 02 May 2008
Posts: 1519
Location: Canada

PostPosted: Wed Sep 05, 2018 15:21    Post subject: Reply with quote
mac913 wrote:
Router: WiFi R7000 (2.4Ghz + 2 VAPs & 5Ghz +VAP)
Firmware: DD-WRT v3.0-r36840M kongac (09/03/2018)
Kernel Version : Linux 4.4.153 #598 SMP Mon Sep 3 22:38:12 CEST 2018 armv7l
Status: Gone Back to Spare R7000 with Working 35550M
Reset: No
Previous: 36410M
Errors: Can Not Connect to VAP on 5Ghz (WL1.1)


With the WiFi Router with build 36840M I did an "erase nvramm" and "reboot" and started creating my 2 VAPs on the 2.4Ghz Radio and one VAP on the 5Ghz Radio. The one problem I'm seeing is that the 5Ghz VAP has the same MAC Address as the 2.4Ghz #2 VAP....

Code:
Firmware: DD-WRT v3.0-r36840M kongac (09/03/18)
Time: 01:05:55 up 5 min, load average: 0.00, 0.04, 0.00
WAN IP: 0.0.0.0

Virtual Interfaces wl0.2 SSID [dd-wrt_vap] HWAddr [E6:F4:xx:xx:xx:FA]

Virtual Interfaces wl1.1 SSID [dd-wrt_vap] HWAddr [E6:F4:xx:xx:xx:FA]


I did try changing the MAC Address Manually on one of the VAP through the GUI and it would go back to the same MAC Address, so I am unable to change the MAC Address.

_________________
Home Network on Telus PureFibre - 10GbE Copper Backbone
2x R7800 - Gateway WiFi 3xWireGuard - DDWRT r43290 Std
WHR-HP-G54 - Internal Routing - DDWRT r35531 std-special
2x E3000 - Gateway Wired IPTV - DDWRT r35531 Mega
E3000 - TRAVEL Wireless Client WireGuard(+25Mbit/s) - DDWRT r43290 Mega

Off Site 1

R7000 - Gateway, WiFi & WireGuard - DDWRT r43217 Std
WRT610Nv1 - Client Bridge - DDWRT r33679 Mega K2.4

Off Site 2

R7000 - Gateway & WiFi - DDWRT r43217 Std
E2000 - Wired PVR Blocker - DDWRT r35531


YAMon 3.4.6 | DNSCrypt-Proxy V2


Last edited by mac913 on Fri Sep 07, 2018 14:33; edited 1 time in total
egc
DD-WRT Guru


Joined: 18 Mar 2014
Posts: 5544
Location: Netherlands

PostPosted: Wed Sep 05, 2018 16:02    Post subject: Reply with quote
I have a modified Linkys EA6900 (MAC addresses are in the CFE for this router so can be changed in CFE), I started with setting MAC address for eth2 further away from eth1 (I used +2) to create room for MAC addresses of more than one VAP.
You could try a similar thing, so start with increasing the MAC address of eth2
You probably have to erase nvram then set MAC address of eth2 + 2, as the MAC addresses of the VAP are then derived from eth1 and eth2.

Never tried it just a thought

_________________
Routers:Netgear R7800, Netgear R6400v1, Netgear R6400v2, Linksys EA6900 (XvortexCFE), Linksys E2000 (converted WRT320N), WRT54GS v1.
Install guide Linksys EA6900: http://www.dd-wrt.com/phpBB2/viewtopic.php?t=291230
OpenVPN Policy Based Routing guide: https://forum.dd-wrt.com/phpBB2/viewtopic.php?t=321686
Install guide R6400v2:http://forum.dd-wrt.com/phpBB2/viewtopic.php?t=316399
OpenVPN Server Setup:https://forum.dd-wrt.com/phpBB2/viewtopic.php?t=318795
Install guide R7800: https://forum.dd-wrt.com/phpBB2/viewtopic.php?t=320614
Wireguard server setup guide:https://forum.dd-wrt.com/phpBB2/viewtopic.php?p=1183135
Wireguard client setup guide:https://forum.dd-wrt.com/phpBB2/viewtopic.php?t=324624
Wireguard Advanced setup guide:https://forum.dd-wrt.com/phpBB2/viewtopic.php?t=324787
hebeda
DD-WRT User


Joined: 18 Sep 2006
Posts: 408
Location: Leipzig, Germany

PostPosted: Wed Sep 05, 2018 16:13    Post subject: Reply with quote
r8000
gui unaccessable after 30 minutes, no telnet either ... AFTER reset gui ....

same happens after erase nvram .... after 30 minutes is the gui not accessable any longer

any suggestion for a working stable version ? brainslayer or kong build ?!
Muzeneer
DD-WRT User


Joined: 06 Jan 2018
Posts: 56

PostPosted: Wed Sep 05, 2018 16:47    Post subject: Reply with quote
Router Model: Netgear R6400 v2 (board_id=U12H332T20_NETGEAR)
Firmware Version: DD-WRT v3.0-r36840M kongac (09/03/2018)
Kernel Version: Linux 4.4.153 #598 SMP Mon Sep 3 22:38:12 CEST 2018 armv7

Previous: v3.0-r36820M kongac (ddup upgrade)
Reset: no

Configuration: AP on 2.4 GHz and 5 Ghz + VAP on 2.4 GHz.

Status: Up and stable for 12 h
Errors:
Code:
Sep 5 18:34:31 DD-WRT_Router daemon.err httpd[1186]: Request Error Code 408: No request appeared within a reasonable time period.
Sep 5 18:35:34 DD-WRT_Router daemon.warn dnsmasq-dhcp[1032]: no address range available for DHCP request via br0
Sep 5 18:35:34 DD-WRT_Router daemon.warn dnsmasq-dhcp[1032]: no address range available for DHCP request via br0
Sep 5 18:36:26 DD-WRT_Router daemon.warn dnsmasq-dhcp[1032]: no address range available for DHCP request via br0
Sep 5 18:36:33 DD-WRT_Router daemon.warn dnsmasq-dhcp[1032]: no address range available for DHCP request via br0
Sep 5 18:36:35 DD-WRT_Router daemon.warn dnsmasq-dhcp[1032]: no address range available for DHCP request via br0
Sep 5 18:36:36 DD-WRT_Router daemon.warn dnsmasq-dhcp[1032]: no address range available for DHCP request via br0
Sep 5 18:39:25 DD-WRT_Router daemon.warn dnsmasq-dhcp[1032]: no address range available for DHCP request via br0
Sep 5 18:39:25 DD-WRT_Router daemon.warn dnsmasq-dhcp[1032]: no address range available for DHCP request via br0
Sep 5 18:39:27 DD-WRT_Router daemon.warn dnsmasq-dhcp[1032]: no address range available for DHCP request via br0
Sep 5 18:40:36 DD-WRT_Router daemon.warn dnsmasq-dhcp[1032]: no address range available for DHCP request via br0
Sep 5 18:40:37 DD-WRT_Router daemon.warn dnsmasq-dhcp[1032]: no address range available for DHCP request via br0
slice1900
DD-WRT User


Joined: 18 Feb 2013
Posts: 99

PostPosted: Wed Sep 05, 2018 19:53    Post subject: Reply with quote
egc wrote:
I have a modified Linkys EA6900 (MAC addresses are in the CFE for this router so can be changed in CFE), I started with setting MAC address for eth2 further away from eth1 (I used +2) to create room for MAC addresses of more than one VAP.
You could try a similar thing, so start with increasing the MAC address of eth2
You probably have to erase nvram then set MAC address of eth2 + 2, as the MAC addresses of the VAP are then derived from eth1 and eth2.

Never tried it just a thought



I don't think the MAC duplication is really a problem since they are different physical networks but just to make things simpler/clearer for me I did similar for my TM1900/AC68Us. I changed the last two octets of my et0macaddr to :10 on my first router, :20 on the second and so forth to help tell the MAC addresses apart for client-side troubleshooting. Then I set 0.macaddr to et0macaddr+4 and 1.macaddr to et0macaddr+8 to leave a bit more breathing room for the two VAPs I have on both 2.4 & 5 GHz.

During my testing I noticed I could change et0_macaddr in NVRAM and commit the changes, and it would be obeyed. I assume the same would be true with 0.macaddr & 1.macaddr, though I didn't try it. So if the OP doesn't want to modify CFE, he can first try modifying the addresses stored in NVRAM and see if they'll stick and be obeyed on his router model. If he erases nvram they'll need to be changed again, of course.
Malachi
DD-WRT Guru


Joined: 17 Jul 2012
Posts: 7267
Location: Columbus, Ohio

PostPosted: Wed Sep 05, 2018 22:13    Post subject: Reply with quote
New rt-ac68u B2 1.4ghz cpu. Sent info to BS two weeks ago to get it added.

Router Model Asus RT-AC68U
Firmware Version DD-WRT v3.0-r36840M kongac (09/03/1Cool
Kernel Version Linux 4.4.153 #598 SMP Mon Sep 3 22:38:12 CEST 2018 armv7l

Everything working fine so far, up 13+ hours.

_________________
I am far from a guru, I'm barely a novice.
Goto page 1, 2, 3  Next Display posts from previous:    Page 1 of 3
Post new topic   Reply to topic    DD-WRT Forum Forum Index -> Broadcom SoC based Hardware All times are GMT

Navigation

 
Jump to:  
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
You can attach files in this forum
You can download files in this forum