This build thread is for reporting successes and problem with loading this experimental test build. This is important info for developers and users. Always state your hardware and SPECIFIC build (e.g. 31924_NEWD-2_K2.6_mega-nv64k.bin). Do not ask questions about your specific router or how to configure it in this thread; create your own thread to discuss any specific problems you have or need resolved. Please also do not respond to such questions. This thread is to report info, not to seek it. Posts that do not add to understanding this build will be deleted. Make sure you know how to flash properly and the risk before using this build. It is important to adhere to these requirements, to keep this thread from becoming impossibly long and useless.
If you don't know what build to flash and how to flash properly and have a means of recovery if things should go wrong, do NOT flash this experimental test build.
_________________ [I prefer answere in whole sentence]
Report for the unofficially supported -- Asus RT-N12D1 (shows as RT-N12B)
DD-WRT v3.0-r31924 mega (05/02/17)
Linux 3.10.105 #14590 Tue May 2 11:59:36 CEST 2017 mips
[dd-wrt.v24-31924_NEWD-2_K3.x_mega.bin]
Install over last release.
NO RESET
Tis just a WAP + Guest
Working very well
:~# date
Wed May 3 09:34:35 CDT 2017
:~# uptime
09:34:38 up 17:34, load average: 0.05, 0.05, 0.04
Joined: 26 Mar 2013 Posts: 1858 Location: Hung Hom, Hong Kong
Posted: Wed May 03, 2017 15:08 Post subject: Asus RT-N18U and DD-WRT build 31924
Router Name: Asus RT-N18U
Router Model: Asus RT-N18U
Firmware: DD-WRT v3.0-r31924 std (05/02/17)
Kernel: Linux 4.4.65 #1439 Tue May 2 07:17:08 CEST 2017 armv7l
Previous: DD-WRT v3.0-r31899 std (04/24/17)
Status: AP Working
Reset: NO reset during firmware upgrade
Errors: Working (I don't use VPN)
1. Clicking Disable, Apply Settings, then Enable in Services->Core USB no longer caused DD-WRT to crash like build 31899
2. LAN LED ... too lazy to check! Meow...
3. DDNS function working normally and didn't crash like 31722
4. wireless working normally
Attached Speedtest result as image, using a 100M internet line provided by HKBN.
a0503.6267977602.png
Description:
Filesize:
21.19 KB
Viewed:
17960 Time(s)
_________________ Router: Asus RT-N18U (rev. A1)
Drink, Blink, Stretch! Live long and prosper! May the Force and farces be with you!
still does not take on rt-ac88u. It shows old build number in top right corner of web ui.
RT-AC3100, same problem. Last working build was 03-21-2017-r31722.
Do we know what commit broke it?
It's a size problem. The installer is reporting that the linux partition has been exceeded. r31722 works because its 29.7 MB. Most of the firmwares in 2017 for the RT-AC88U have exceed 30 MB which causes the oversize partition error. The r31924 is 30.4 MB so it will not work.
Did a fresh install on another Netgear R8000 yesterday and found two problems.
1. Was unable to break out of the Netgear firmware with build R31923 - incompatible firmware type error. Used current Kong build to break out, which went without error, so looks like the factory-to-dd-wrt.chk is currently bad for this model.
2. Re-installed BS main build over above image and successfully configured up to replace functionality on old router - multiple VLANs, extra bridge for guest wireless, iptables scripts, guest wireless virtual interfaces, QoS, OpenVPN, USB JFFS etc. Internet connection is PPPoE service, system worked perfectly, however when I take the number of ports connected to VLAN 1 from 2 down to 1, the Internet connectivity then fails on the resart. interface ppp0 is no longer present if you do an ifconfig, hence no Internet connection. Adding any other LAN port back to VLAN 1 resolves issue.
The problem can be re-created with any of the LAN ports. Any 2 or more ports = works fine. Only one port in VLAN 1 and ppp0 fails to appear. At all times VLAN 5 and 8 only have one port assigned and that did not seem to affect anything, so VLAN 1 port count is the thing that breaks this.
Swapped to current Kong build (R31870), made no changes to configuration and it works fine. I note that it take a short period for the ppp0 interface to appear in ifconfig list, but it all comes up OK.
Posted: Fri May 05, 2017 12:49 Post subject: re: New build is out 31924 (BS) 2017-05-03
Linksys WRT1900ACS v1
I had a kong build from January but wanted to update just to be on top of things, so installed this build over the kong build and it's working just fine. It rebooted automagically and nothing has gone wrong.
Linux 3.18.51 #131 SMP armv7l
5 MAY 17 0538AM
Firmware: DD-WRT v3.0-r31100M kongmv (01/08/17)
Time: 05:36:14 up 1 day, 26 min, load average: 0.00, 0.00, 0.00
CPU Model: Marvel Armada 385
CPU Cores: 2
CPU Clock: 1600 MHz
Load Average: 0% 0.00, 0.00, 0.00
CPU Temperature: CPU 71.3 °C / WL0 45.6 °C / WL1 46.8 °C
-------------------
Linux 3.18.51 #131 SMP armv7l
5 MAY 17 0745AM
Firmware: DD-WRT v3.0-r31924 std (05/02/17)
Time: 07:47:52 up 2:06, load average: 0.00, 0.00, 0.00
CPU Model: Marvel Armada 385
CPU Cores: 2
CPU Clock: 1600 MHz
Load Average: 0% 0.00, 0.00, 0.00
CPU Temperature: CPU 70.8 °C / WL0 45.5 °C / WL1 46.6 °C
Posted: Fri May 05, 2017 12:57 Post subject: Re: re: New build is out 31924 (BS) 2017-05-03
Pflarg wrote:
Linksys WRT1900ACS v1
I had a kong build from January but wanted to update just to be on top of things, so installed this build over the kong build and it's working just fine. It rebooted automagically and nothing has gone wrong.
Linux 3.18.51 #131 SMP armv7l
5 MAY 17 0538AM
Firmware: DD-WRT v3.0-r31100M kongmv (01/08/17)
Time: 05:36:14 up 1 day, 26 min, load average: 0.00, 0.00, 0.00
CPU Model: Marvel Armada 385
CPU Cores: 2
CPU Clock: 1600 MHz
Load Average: 0% 0.00, 0.00, 0.00
CPU Temperature: CPU 71.3 °C / WL0 45.6 °C / WL1 46.8 °C
-------------------
Linux 3.18.51 #131 SMP armv7l
5 MAY 17 0745AM
Firmware: DD-WRT v3.0-r31924 std (05/02/17)
Time: 07:47:52 up 2:06, load average: 0.00, 0.00, 0.00
CPU Model: Marvel Armada 385
CPU Cores: 2
CPU Clock: 1600 MHz
Load Average: 0% 0.00, 0.00, 0.00
CPU Temperature: CPU 70.8 °C / WL0 45.5 °C / WL1 46.6 °C
That's a Marvell unit, not Broadcom, wrong forum _________________ R6400v2 (boardID:30) - Kong 36480 running since 03/09/18 - (AP - DNSMasq - AdBlocking - QoS) R7800 - BS 31924 running since 05/26/17 - (AP - OpenVPN Client - DNSMasq - AdBlocking - QoS) R7000 - BS 30771 running since 12/16/16 - (AP - NAS - FTP - SMB - OpenVPN Server - Transmission - DDNS - DNSMasq - AdBlocking - QoS) R6250 - BS 29193 running since 03/20/16 - (AP - NAS - FTP - SMB - DNSMasq - AdBlocking)
Router: Asus RT-N16
Firmware: dd-wrt.v24-31924_NEWD-2_K2.6_mega.bin
Kernel: Linux 2.6.24.111 #31257 Tue May 2 00:47:30 CEST 2017 mips
Reset: Reset after firmware upgrade, then restore config
Errors: 1.Incorrect wifi signal value.
2. Status_OpenVPN.asp not show info about my connection as client OpenVPN.
Scripts /etc/openvpnlog.sh /etc/openvpnstate.sh /etc/openvpnstatus.sh work properly.
Screenshots here
Router: Asus RT-AC66U
Firmware: DD-WRT v3.0-r31924 giga (05/02/17)
Previous: DD-WRT v3.0-r31899 giga (04/24/17)
Kernel: Linux 3.10.105 #14570 Tue May 2 11:41:31 CEST 2017 mips
Status: OK but BusyBox wget command is broken (v1.26.2)
Reset: No
Errors: None
IPv6 DHCPv6 PD: OK
WAN/LAN ports: OK
2.4GHz AP: OK
5GHz AP: unused
Site Survey: OK
Wiviz Survey: OK
OpenVPN Client: OK tunneling IPv4+IPv6
USB Flash Drive: OK mounting /opt, /jffs, /swap partitions
CPU Temperature: WL0 45.8 °C / WL1 unused _________________ [Broadcom] Asus rt-ac66u r35531 ('66 should only be factory reset through the DD UI)
Fix RT-AC66U "wl1 [2.4 GHz TurboQAM]". DD-WRT failsafe UI @ http|https://169.254.255.1/
