New Kong's build: DD-WRT 30800M - 10/27/2016

Post new topic   Reply to topic    DD-WRT Forum Forum Index -> Broadcom SoC based Hardware
Goto page 1, 2, 3, 4  Next
Author Message
Xeon2k8
DD-WRT Guru


Joined: 11 Feb 2016
Posts: 1286

PostPosted: Thu Oct 27, 2016 17:28    Post subject: New Kong's build: DD-WRT 30800M - 10/27/2016 Reply with quote
Kong's DD-WRT build 30800M - 10/27/2016 has been released:
http://desipro.de/ddwrt/K3-AC-Arm/

Your reports for Broadcom units are greatly appreciated !
Router:
Firmware:
Kernel:
Previous:
Status:
Reset:
Errors:

This build thread is for reporting successes and problem with loading this experimental test build. This is important info for developers and users. Always state your hardware and SPECIFIC build (e.g. 30796_NEWD-2_K2.6_mega-nv64k.bin). Do not ask questions about your specific router or how to configure it in this thread; create your own thread to discuss any specific problems you have or need resolved. Please also do not respond to such questions. This thread is to report info, not to seek it. Posts that do not add to understanding this build will be deleted. Make sure you know how to flash properly and the risk before using this build. It is important to adhere to these requirements, to keep this thread from becoming impossibly long and useless.
If you don't know what build to flash and how to flash properly and have a means of recovery if things should go wrong, do NOT flash this experimental test build.
Sponsor
ciscodlink
DD-WRT User


Joined: 13 May 2014
Posts: 254

PostPosted: Thu Oct 27, 2016 18:35    Post subject: Reply with quote
.nvm

Last edited by ciscodlink on Wed Nov 02, 2016 19:15; edited 1 time in total
cdmarshall
DD-WRT User


Joined: 09 Jul 2014
Posts: 308

PostPosted: Thu Oct 27, 2016 20:18    Post subject: Reply with quote
http://svn.dd-wrt.com/timeline

And you can see whats been worked fixed and added

_________________
EA-6900
Asus 68U
cc999
DD-WRT User


Joined: 20 Feb 2015
Posts: 110

PostPosted: Fri Oct 28, 2016 0:30    Post subject: Not Good Reply with quote
R8500
Updated thru telnet

Lasted 2 hours, streaming to my laptop (5 ghz) caused a complete router crash.This is after about 30 minutes into the stream.

ver 30700 ran flawlessly. I went back to 30700.

I did NOT clear nvram just updated from the telnet prompt as stated before. Whether or not that is a problem when moving up to this version I guess only KONG can answer.

CC
mrjcd
DD-WRT Guru


Joined: 31 Jan 2015
Posts: 5398
Location: Texas

PostPosted: Fri Oct 28, 2016 1:33    Post subject: Re: Not Good Reply with quote
cc999 wrote:
R8500
Updated thru telnet

Lasted 2 hours, streaming to my laptop (5 ghz) caused a complete router crash.This is after about 30 minutes into the stream.

ver 30700 ran flawlessly. I went back to 30700.

I did NOT clear nvram just updated from the telnet prompt as stated before. Whether or not that is a problem when moving up to this version I guess only KONG can answer.

CC


Well my longest run on the EA8500 was 23 minutes... several crash/reboots before Razz
cc999
DD-WRT User


Joined: 20 Feb 2015
Posts: 110

PostPosted: Fri Oct 28, 2016 1:56    Post subject: Re: Not Good Reply with quote
mrjcd wrote:
cc999 wrote:
R8500
Updated thru telnet

Lasted 2 hours, streaming to my laptop (5 ghz) caused a complete router crash.This is after about 30 minutes into the stream.

ver 30700 ran flawlessly. I went back to 30700.

I did NOT clear nvram just updated from the telnet prompt as stated before. Whether or not that is a problem when moving up to this version I guess only KONG can answer.

CC


Well my longest run on the EA8500 was 23 minutes... several crash/reboots before Razz


Looks like this build is a no go.

CC
mrjcd
DD-WRT Guru


Joined: 31 Jan 2015
Posts: 5398
Location: Texas

PostPosted: Fri Oct 28, 2016 2:00    Post subject: Re: Not Good Reply with quote
cc999 wrote:
mrjcd wrote:
cc999 wrote:
R8500
Updated thru telnet

Lasted 2 hours, streaming to my laptop (5 ghz) caused a complete router crash.This is after about 30 minutes into the stream.

ver 30700 ran flawlessly. I went back to 30700.

I did NOT clear nvram just updated from the telnet prompt as stated before. Whether or not that is a problem when moving up to this version I guess only KONG can answer.

CC


Well my longest run on the EA8500 was 23 minutes... several crash/reboots before Razz


Looks like this build is a no go.

CC

I haven't reset either --- but plan to soon... Thinking that would be the sensible thing to do. Kong usually knows what he's doing ---
e3000usr
DD-WRT User


Joined: 09 Jul 2014
Posts: 183

PostPosted: Fri Oct 28, 2016 5:01    Post subject: Reply with quote
Router: Asus RT-AC56U
Firmware: DD-WRT v3.0-r30800M kongac (10/27/16)
Kernel: Linux 4.4.25 #134 SMP Thu Oct 27 16:01:52 CEST 2016 armv7l
Previous: DD-WRT v3.0-r30700M kongac (09/27/16)
Status: OK
Reset: NO
Errors: NO

Thank you Kong!
limerick_fr
DD-WRT User


Joined: 07 Nov 2012
Posts: 111

PostPosted: Fri Oct 28, 2016 5:04    Post subject: Reply with quote
12 hours running now on my R8000.
<Kong>
DD-WRT Guru


Joined: 15 Dec 2010
Posts: 4339
Location: Germany

PostPosted: Fri Oct 28, 2016 5:32    Post subject: Re: Not Good Reply with quote
cc999 wrote:
R8500
Updated thru telnet

Lasted 2 hours, streaming to my laptop (5 ghz) caused a complete router crash.This is after about 30 minutes into the stream.

ver 30700 ran flawlessly. I went back to 30700.

I did NOT clear nvram just updated from the telnet prompt as stated before. Whether or not that is a problem when moving up to this version I guess only KONG can answer.

CC


I do not recall a lot of changes that have any potential to cause this. Mostly little fixes that cannot cause crashes.

Ndpi was the biggest change which is a kernel module and therefore would be my first candidate for inspection. Are you
doing any protocol prioritization/blocking?

_________________
KONG PB's: http://www.desipro.de/ddwrt/
KONG Info: http://tips.desipro.de/
cc999
DD-WRT User


Joined: 20 Feb 2015
Posts: 110

PostPosted: Fri Oct 28, 2016 10:47    Post subject: Re: Not Good Reply with quote
<Kong> wrote:
cc999 wrote:
R8500
Updated thru telnet

Lasted 2 hours, streaming to my laptop (5 ghz) caused a complete router crash.This is after about 30 minutes into the stream.

ver 30700 ran flawlessly. I went back to 30700.

I did NOT clear nvram just updated from the telnet prompt as stated before. Whether or not that is a problem when moving up to this version I guess only KONG can answer.

CC


I do not recall a lot of changes that have any potential to cause this. Mostly little fixes that cannot cause crashes.

Ndpi was the biggest change which is a kernel module and therefore would be my first candidate for inspection. Are you
doing any protocol prioritization/blocking?


KONG,

IN QOS I am using Services Priority

apple
netflix
httpvideo
httpaudio
youtube

I have been using this setting for months now. This is the first time in months I actuallyt had a full out router crash.

Could that be the cause?

CC
CloneVince
DD-WRT User


Joined: 31 May 2014
Posts: 219

PostPosted: Fri Oct 28, 2016 10:54    Post subject: Reply with quote
R7000 updated with
Code:
ddup --flash-latest


It took a lot of times before reboot, but all was done.

Thx Kong Smile

_________________
Unofficial Kong's release repository : http://ddwrt-kong.clonevince.fr/
kallsop
DD-WRT User


Joined: 10 Apr 2008
Posts: 135

PostPosted: Fri Oct 28, 2016 11:33    Post subject: Reply with quote
R7000
DD-WRT v3.0-r30800M kongac (10/27/16)
Linux 4.4.25 #134 SMP Thu Oct 27 16:01:52 CEST 2016 armv7l

Loaded code via GUI upload, no reset. Everything running ok so far, 12 hours uptime: WAN, dual band WiFi, DHCP and static IP, VPN, QoS, port forwarding, firewall rules, ...
Ah-Pin-Kor
DD-WRT User


Joined: 19 Sep 2015
Posts: 267

PostPosted: Fri Oct 28, 2016 12:44    Post subject: Reply with quote
Router: D-Link DIR-885L
Firmware: DD-WRT v3.0-r30800M kongac (10/27/16)
Kernel: Linux 4.4.25 #134 SMP Thu Oct 27 16:01:52 CEST 2016 armv7l
Previous: DD-WRT v3.0-r30700M kongac (09/27/16)
Status: OK
Reset: No
Errors: None so far

Thanks Kong & BS.

_________________

Netgear R7800 kongpro 19.07 20190919 || Netgear R7000 36070M kongac (Client Bridge=5GHz, AP=2.4GHz with bridged VAP)
Linksys WRT32X davidc502 OpenWrt || Linksys WRT1200ACv1 Gargoyle 1.11.x
Linksys WRT1900ACSv2 dd-wrt 39956
cc999
DD-WRT User


Joined: 20 Feb 2015
Posts: 110

PostPosted: Fri Oct 28, 2016 13:35    Post subject: Re: Not Good Reply with quote
<Kong> wrote:
cc999 wrote:
R8500
Updated thru telnet

Lasted 2 hours, streaming to my laptop (5 ghz) caused a complete router crash.This is after about 30 minutes into the stream.

ver 30700 ran flawlessly. I went back to 30700.

I did NOT clear nvram just updated from the telnet prompt as stated before. Whether or not that is a problem when moving up to this version I guess only KONG can answer.

CC


I do not recall a lot of changes that have any potential to cause this. Mostly little fixes that cannot cause crashes.

Ndpi was the biggest change which is a kernel module and therefore would be my first candidate for inspection. Are you
doing any protocol prioritization/blocking?


KONG,

Now I nvram erased, reflashed (30800), nvram erased again and started to put in my settings manually. When I went to the Services tab and added 15 spots for the static ip's (like I do for every build) I got to about 11 then the router crashed.
This never happened before.

I then nvram erased, reflashed (307000}, nvram erased again and started to put in my settings manually. Again goto the services tab and there were no problems at all. Something is wrong in a few areas for the R8500 in this build.

Back on 30700 and everything is running perfectly again.

CC
Goto page 1, 2, 3, 4  Next Display posts from previous:    Page 1 of 4
Post new topic   Reply to topic    DD-WRT Forum Forum Index -> Broadcom SoC based Hardware All times are GMT

Navigation

 
Jump to:  
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
You can attach files in this forum
You can download files in this forum