Posted: Sat Jun 04, 2016 20:15 Post subject: Kong's 29825 build of 4 JUNE '16
New builds by <Kong> released this evening. Performance is pretty much the same as with the last two builds released in May, so not sure at present what changes have been made. No complaints though!
Regards, lim _________________ WRT1900ACS v1
WRT3200ACM
Regulatory Domain: UK
Last edited by lim on Fri Jun 10, 2016 12:06; edited 1 time in total
Posted: Sat Jun 04, 2016 20:29 Post subject: Re: Kong's build 29825 of 4 JUNE '16
lim wrote:
New builds by <Kong> released this evening. Performance is pretty much the same as with the last two builds released in May, so not sure at present what changes have been made. No complaints though!
Posted: Sat Jun 04, 2016 20:35 Post subject: Re: Kong's build 29825 of 4 JUNE '16
<Kong> wrote:
lim wrote:
New builds by <Kong> released this evening. Performance is pretty much the same as with the last two builds released in May, so not sure at present what changes have been made. No complaints though!
Regards, lim
Comes with latest drivers and updated mac80211, BrainSlayers builds should have the same performance now.
Thank you so much for all your efforts for the users; it is greatly appreciated.
Regards, lim _________________ WRT1900ACS v1
WRT3200ACM
Regulatory Domain: UK
Thanks Kong, working well and now able to use VHT80 for the first time 😀😀 _________________ Linksys WRT 1900AC - V2
Firmware:DD-WRT v3.0-r30015M kongmv (24/June/16)
1. For 2.4GHz., missing channels 4, 5, 6, 7, and 8. They're just not in the list of channels. In particular missing channel 6. Channel 6 is the one that works best around here.
2. Put the 5GHz. on 80MHz. channel 157/upper, and it came up on channel 161. Switched it to 157/lower, and it didn't work at all, and neither did the second try at 157/upper. Now it's set at 40MHz. channel 157, and that works. Too bad no 80MHz. channel with 157 as primary channel.
Odd, anyone else seeing this sort of thing?
The wireless is working, but channel selection appears to be borked.
Might just need to go back a release? Or reflash? Just weird.
1. For 2.4GHz., missing channels 4, 5, 6, 7, and 8. They're just not in the list of channels. In particular missing channel 6. Channel 6 is the one that works best around here.
Same here on point above. It works, had to switch to channel 9 as the ones above were not listed.
Posted: Sun Jun 05, 2016 21:48 Post subject: 2.4ghz goes missing
I had my 2.4Ghz channel stop responding and knocked everyone off. The 5Ghz kept running fine. I had to reboot to get it working again. Looking at the console, it showed that the 2.4Ghz range was still being recognized... but most clients weren't visible any longer in the connections list.
I'm running the 6/4 version, but this happened on the previous version as well. Unfortunately I don't know any commands to run to give you a crash dump of what is happening on the router at that time, and would appreciate anyone to share that info for next time it happens? Thank you! _________________ Device: Linksys WRT1900AC V1
Firmware: Kong Build 31100 1/8/2017
Kong Links: http://www.desipro.de/ddwrt/K3-AC-MVEBU/
BS Links: ftp://ftp.dd-wrt.com/betas/
I picked channel 3 on 2.4GHz. Don't like it, since it overlaps with other channels, but channels 1 and 11 are fully occupied here. Luckily I only need 2.4GHz. for a wifi printer that's not on very often, everything else is on 5GHz.
I am pining for good ol' channel 6 though, I want it back *smile*.
Note that I did try clearing my browser cache, just to see if the "missing channels" was because of that. Didn't help. Also have flashed latest openWRT now, too, so I know that the router's okay, too. And all channels are available again. Will come back to Kong when the channels are restored.
Last edited by MrDoh on Mon Jun 06, 2016 17:34; edited 4 times in total
