DD-WRT :: View topic - New Build - 12/01/2015

New Build - 12/01/2015 - r28397

DD-WRT Forum Index -> Atheros WiSOC based Hardware

Goto page Previous 1, 2, 3 Next

View previous topic :: View next topic

Author

Message

Doppel-D
DD-WRT User

Joined: 13 Jul 2014
Posts: 215
Location: Germany

Posted: Tue Dec 01, 2015 21:41 Post subject:

Mile-Lile wrote:

Errors: newly created VAP doesn't broadcast

Had VAP configured but had signal disabled . Enable & "Apply" wasn't enough to get VAP going -> no IP. Reboot necessary.

Sponsor

samgu
DD-WRT User

Joined: 17 Jul 2011
Posts: 67

Posted: Tue Dec 01, 2015 22:48 Post subject:

Router Model: TP TL-WDR4300 v1
Status: OK
Reset: No
Errors: Not sure

When I apply changes, the main page doesn't load completely all the time. A simple refresh solves that.

That other situation is that the 2.4GHz network is working good, better than with the factory firmware. BUT, the 5GHz is weird. My "family" laptop is 5 meters or 16 feet away from the router, without any physical barriers between. The strengh signal is bellow 45%.

Is that right? Shouldn't that be a bit better?

redhawk0
DD-WRT Guru

Joined: 04 Jan 2007
Posts: 11564
Location: Wherever the wind blows- North America

Posted: Tue Dec 01, 2015 23:33 Post subject:

redhawk0 wrote:

Argorr wrote:

Do you use dhcp forwarder on the setup page? That's what happened to me on the last release. It was fixed by turning it back to just dhcp but disabled. Just curious.

Actually....Yes...I do have it set as a DHCP Forwarder....I'll try a different setup on this unit and report back.

Thanx for the info.

redhawk

Sorry guys....changing from DHCP Forwarder to DHCP Server (disabled) didn't help with this unit. Still the same problem.

I'm back on 27858 as a DHCP Forwarder.

redhawk
_________________
The only stupid question....is the unasked one.

Doppel-D
DD-WRT User

Joined: 13 Jul 2014
Posts: 215
Location: Germany

Posted: Tue Dec 01, 2015 23:46 Post subject:

samgu wrote:

Router Model: TP TL-WDR4300 v1
BUT, the 5GHz is weird. My "family" laptop is 5 meters or 16 feet away from the router, without any physical barriers between. The strengh signal is bellow 45%.

Is that right? Shouldn't that be a bit better?

With how many dBm you are transmitting? there are different channel (groups) which uses different power.

samgu
DD-WRT User

Joined: 17 Jul 2011
Posts: 67

Posted: Wed Dec 02, 2015 0:56 Post subject:

Doppel-D wrote:

samgu wrote:

With how many dBm you are transmitting? there are different channel (groups) which uses different power.

I am transmitting with 21dBm, because I choose the 104 channel UPPER. The list I got from the "iw list" command is:

* 5180 MHz [36] (17.0 dBm)
* 5200 MHz [40] (17.0 dBm)
* 5220 MHz [44] (17.0 dBm)
* 5240 MHz [48] (17.0 dBm)
* 5260 MHz [52] (17.0 dBm)
* 5280 MHz [56] (17.0 dBm)
* 5300 MHz [60] (17.0 dBm)
* 5320 MHz [64] (17.0 dBm)
* 5500 MHz [100] (17.0 dBm)
* 5520 MHz [104] (21.0 dBm)
* 5540 MHz [108] (21.0 dBm)
* 5560 MHz [112] (21.0 dBm)
* 5580 MHz [116] (21.0 dBm)
* 5600 MHz [120] (17.0 dBm)
* 5620 MHz [124] (17.0 dBm)
* 5640 MHz [128] (17.0 dBm)
* 5660 MHz [132] (17.0 dBm)
* 5680 MHz [136] (17.0 dBm)
* 5700 MHz [140] (17.0 dBm)
* 5720 MHz [144] (17.0 dBm)
* 5745 MHz [149] (21.0 dBm)
* 5765 MHz [153] (21.0 dBm)
* 5785 MHz [157] (21.0 dBm)
* 5805 MHz [161] (21.0 dBm)
* 5825 MHz [165] (20.0 dBm)

The region I am using is Brazil.

teslacoil
DD-WRT User

Joined: 29 Nov 2015
Posts: 129

Posted: Wed Dec 02, 2015 2:19 Post subject:
Router Model: DIR-615E3 Status: Not OK Reset: 30/30/30 reset before & after flash Errors: Internet slowdowns after about an hour of heavy use; speeds up then slows down again. Reverted back to 27745 which is the most recent build that works without this problem on this router.

Doppel-D
DD-WRT User

Joined: 13 Jul 2014
Posts: 215
Location: Germany

Posted: Wed Dec 02, 2015 5:47 Post subject:

samgu wrote:

I am transmitting with 21dBm,

Not much. Other country setting e.g. Canada?

Mile-Lile
DD-WRT Guru

Joined: 24 Feb 2013
Posts: 1634
Location: Belgrade

Posted: Wed Dec 02, 2015 6:58 Post subject:

Doppel-D wrote:

Mile-Lile wrote:

Errors: newly created VAP doesn't broadcast

Had VAP configured but had signal disabled . Enable & "Apply" wasn't enough to get VAP going -> no IP. Reboot necessary.

reboot did not helped in my case... here is dmesg, maybe it will tell something to devs

Quote:

<5>[ 0.000000] Linux version 3.18.24 (root@nmndev) (gcc version 5.2.0 (OpenWrt GCC 5.2.0 r46799) ) #6609 Tue Dec 1 03:28:17 CET 2015
<6>[ 0.000000] bootconsole [early0] enabled
<6>[ 0.000000] CPU0 revision is: 00019750 (MIPS 74Kc)
<4>[ 0.000000] cpu apb ddr apb cpu 720 ddr 600 ahb 200
<6>[ 0.000000] sys id = 1130 Qualcomm Atheros QCA9558 ver 1 rev 1.0 (0x1130)
<6>[ 0.000000] Determined physical RAM map:
<6>[ 0.000000] memory: 04000000 @ 00000000 (usable)
<4>[ 0.000000] Zone ranges:
<4>[ 0.000000] Normal [mem 0x00000000-0x03ffffff]
<4>[ 0.000000] Movable zone start for each node
<4>[ 0.000000] Early memory node ranges
<4>[ 0.000000] node 0: [mem 0x00000000-0x03ffffff]
<6>[ 0.000000] Initmem setup node 0 [mem 0x00000000-0x03ffffff]
<7>[ 0.000000] On node 0 totalpages: 16384
<7>[ 0.000000] free_area_init_node: node 0, pgdat 802dd5d0, node_mem_map 81000000
<7>[ 0.000000] Normal zone: 128 pages used for memmap
<7>[ 0.000000] Normal zone: 0 pages reserved
<7>[ 0.000000] Normal zone: 16384 pages, LIFO batch:3
<4>[ 0.000000] Primary instruction cache 64kB, 4-way, VIPT, linesize 32 bytes.
<4>[ 0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
<7>[ 0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
<7>[ 0.000000] pcpu-alloc: [0] 0
<4>[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 16256
<5>[ 0.000000] Kernel command line: console=ttyS0,115200 root=1f02 rootfstype=squashfs noinitrd init=/sbin/init
<6>[ 0.000000] PID hash table entries: 256 (order: -2, 1024 bytes)
<6>[ 0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
<6>[ 0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
<6>[ 0.000000] Writing ErrCtl register=00000000
<6>[ 0.000000] Readback ErrCtl register=00000000
<4>[ 0.000000] Memory: 61488K/65536K available (2255K kernel code, 149K rwdata, 232K rodata, 168K init, 237K bss, 4048K reserved)
<6>[ 0.000000] NR_IRQS:83
<6>[ 0.060000] Calibrating delay loop... 358.80 BogoMIPS (lpj=1794048)
<6>[ 0.060000] pid_max: default: 32768 minimum: 301
<6>[ 0.060000] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
<6>[ 0.070000] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
<6>[ 0.070000] NET: Registered protocol family 16
<7>[ 0.080000] ar71xx: using random MAC address for eth0
<7>[ 0.280000] ar71xx: using random MAC address for eth1
<4>[ 0.490000] ar724x-pci ar724x-pci.0: PCIe link is down
<4>[ 0.500000] registering PCI controller with io_map_base unset
<4>[ 0.500000] ar724x-pci ar724x-pci.1: PCIe link is down
<4>[ 0.510000] registering PCI controller with io_map_base unset
<6>[ 0.520000] PCI host bridge to bus 0000:00
<6>[ 0.520000] pci_bus 0000:00: root bus resource [mem 0x10000000-0x11ffffff]
<6>[ 0.530000] pci_bus 0000:00: root bus resource [io 0x0000]
<6>[ 0.530000] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff]
<7>[ 0.540000] pci_bus 0000:00: busn_res: [bus 00-ff] end is updated to 00
<6>[ 0.540000] PCI host bridge to bus 0000:01
<6>[ 0.540000] pci_bus 0000:01: root bus resource [mem 0x12000000-0x13ffffff]
<6>[ 0.550000] pci_bus 0000:01: root bus resource [io 0x0001]
<6>[ 0.550000] pci_bus 0000:01: No busn resource found for root bus, will use [bus 01-ff]
<7>[ 0.560000] pci_bus 0000:01: busn_res: [bus 01-ff] end is updated to 01
<6>[ 0.560000] Switched to clocksource MIPS
<6>[ 0.560000] NET: Registered protocol family 2
<6>[ 0.570000] TCP established hash table entries: 1024 (order: 0, 4096 bytes)
<6>[ 0.570000] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
<6>[ 0.580000] TCP: Hash tables configured (established 1024 bind 1024)
<6>[ 0.580000] TCP: reno registered
<6>[ 0.590000] UDP hash table entries: 256 (order: 0, 4096 bytes)
<6>[ 0.590000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
<6>[ 0.600000] NET: Registered protocol family 1
<7>[ 0.600000] PCI: CLS 0 bytes, default 32
<5>[ 0.600000] gpio_proc: module loaded and /proc/gpio/ created
<6>[ 0.610000] futex hash table entries: 256 (order: -1, 3072 bytes)
<6>[ 0.620000] squashfs: version 3.0 (2006/03/15) Phillip Lougher
<6>[ 0.620000] msgmni has been set to 120
<6>[ 0.630000] io scheduler noop registered
<6>[ 0.630000] io scheduler deadline registered (default)
<6>[ 0.640000] Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled
<6>[ 0.640000] console [ttyS0] disabled
<6>[ 0.670000] serial8250.0: ttyS0 at MMIO 0x18020000 (irq = 11, base_baud = 2500000) is a 16550A
<6>[ 0.680000] console [ttyS0] enabled
<6>[ 0.680000] bootconsole [early0] disabled
<0>[ 0.690000] guessed flashsize = 8M
<0>[ 0.700000] scanning for root partition
<0>[ 0.700000] tplink uboot detected
<0>[ 0.700000] guessed bootloader size = 20000
<0>[ 0.720000]
<0>[ 0.720000] found squashfs at 110000
<6>[ 0.730000] adjusted length 760000, original length 75F3C0
<5>[ 0.740000] Creating 9 MTD partitions on nal lear7240-nor0
<5>[ 0.740000] 0x000000000000-0x000000020000 : lear7RedBoot0
<5>[ 0.750000] 0x000000020000-0x0000007e0000 : lear7linux;t0
<5>[ 0.750000] 0x000000110000-0x000000770000 : lear7rootfst0
<5>[ 0.760000] mtd: partition 0x0000rootfs00 : set to be root filesystem
<5>[ 0.760000] 0x000000770000-0x0000007e0000 : set ddwrt;root
<5>[ 0.770000] 0x0000007e0000-0x0000007f0000 : set nvram;root
<5>[ 0.770000] 0x0000007f0000-0x000000800000 : set board_config
<5>[ 0.780000] 0x000000000000-0x000000800000 : set fullflashfig
<5>[ 0.790000] 0x000000000000-0x000000020000 : set fullboothfig
<5>[ 0.790000] 0x000000010000-0x000000020000 : set uboot-envfig
<6>[ 0.800000] libphy: Fixed MDIO Bus: probed
<6>[ 0.800000] tun: Universal TUN/TAP device driver, 1.6
<6>[ 0.810000] tun: (C) 1999-2004 Max Krasnyansky
<6>[ 0.820000] u32 classifier
<6>[ 0.820000] Performance counters on
<6>[ 0.830000] input device check on
<6>[ 0.830000] Actions configured
<6>[ 0.830000] Netfilter messages via NETLINK v0.30.
<6>[ 0.840000] nf_conntrack version 0.5.0 (960 buckets, 3840 max)
<4>[ 0.840000] nf_conntrack_rtsp v0.6.21 loading
<4>[ 0.850000] nf_nat_rtsp v0.6.21 loading
<6>[ 0.850000] ip_tables: (C) 2000-2006 Netfilter Core Team
<6>[ 0.860000] TCP: westwood registered
<6>[ 0.860000] TCP: hybla registered
<6>[ 0.860000] TCP: vegas registered
<6>[ 0.870000] NET: Registered protocol family 17
<6>[ 0.870000] bridge: automatic filtering via arp/ip/ip6tables has been deprecated. Update your scripts to load br_netfilter if you need this.
<5>[ 0.890000] Bridge firewalling registered
<6>[ 0.890000] 8021q: 802.1Q VLAN Support v1.8
<6>[ 0.890000] searching for nvram
<6>[ 0.900000] nvram size = 0
<6>[ 0.950000] Atheros AR71xx hardware watchdog driver version 0.1.0
<6>[ 0.950000] ar71xx-wdt: timeout=15 secs (max=107) ref freq=40000000
<6>[ 0.980000] VFS: Mounted root (squashfs filesystem) readonly on device 31:2.
<6>[ 0.990000] Freeing unused kernel memory: 168K (802f6000 - 80320000)
<7>[ 3.630000] ar71xx-wdt: enabling watchdog timer
<6>[ 3.690000] switch0: Atheros AR8327 rev. 4 switch registered on ag71xx-mdio.0
<6>[ 3.790000] libphy: ag71xx_mdio: probed
<6>[ 4.390000] ag71xx ag71xx.0: connected to PHY at ag71xx-mdio.0:00 [uid=004dd034, driver=Atheros AR8216/AR8236/AR8316]
<6>[ 4.400000] eth0: Atheros AG71xx at 0xb9000000, irq 4, mode:RGMII
<6>[ 4.990000] eth1: Atheros AG71xx at 0xba000000, irq 5, mode:SGMII
<6>[ 5.180000] eth1: link up (1000Mbps/Full duplex)
<6>[ 5.260000] Loading modules backported from Linux version master-2015-10-26-0-g28c26cb
<6>[ 5.270000] Backport generated by backports.git backports-20150903-4-g12cf266
<6>[ 5.430000] cfg80211: World regulatory domain updated:
<6>[ 5.430000] cfg80211: DFS Master region: unset
<6>[ 5.440000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time)
<6>[ 5.450000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
<6>[ 5.460000] cfg80211: (2457000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
<6>[ 5.460000] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (N/A, 2000 mBm), (N/A)
<6>[ 5.470000] cfg80211: (5170000 KHz - 5250000 KHz @ 80000 KHz), (N/A, 2000 mBm), (N/A)
<6>[ 5.480000] cfg80211: (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 2000 mBm), (N/A)
<6>[ 5.490000] cfg80211: (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 0 mBm), (N/A)
<7>[ 6.080000] ath: EEPROM regdomain: 0x0
<7>[ 6.080000] ath: EEPROM indicates default country code should be used
<7>[ 6.080000] ath: doing EEPROM country->regdmn map search
<7>[ 6.080000] ath: country maps to regdmn code: 0x3a
<7>[ 6.080000] ath: Country alpha2 being used: US
<7>[ 6.080000] ath: Regpair used: 0x3a
<7>[ 6.090000] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'
<6>[ 6.090000] ieee80211 phy0: Atheros AR9550 Rev:0 mem=0xb8100000, irq=79
<6>[ 6.100000] cfg80211: Regulatory domain changed to country: US
<6>[ 6.110000] cfg80211: DFS Master region: FCC
<6>[ 6.110000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time)
<6>[ 6.120000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 3000 mBm), (N/A)
<6>[ 6.130000] cfg80211: (5170000 KHz - 5250000 KHz @ 80000 KHz), (N/A, 1700 mBm), (N/A)
<6>[ 6.140000] cfg80211: (5250000 KHz - 5330000 KHz @ 80000 KHz), (N/A, 2300 mBm), (N/A)
<6>[ 6.150000] cfg80211: (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 3000 mBm), (N/A)
<6>[ 6.150000] cfg80211: (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 4000 mBm), (N/A)
<6>[ 6.390000] eth0: link up (1000Mbps/Full duplex)
<6>[ 8.270000] device br0 entered promiscuous mode
<6>[ 8.300000] eth1: link down
<6>[ 8.310000] eth1: link up (1000Mbps/Full duplex)
<6>[ 8.330000] eth1: link down
<6>[ 8.340000] eth1: link up (1000Mbps/Full duplex)
<6>[ 8.350000] device eth1 entered promiscuous mode
<6>[ 8.360000] br0: port 1(eth1) entered forwarding state
<6>[ 8.360000] br0: port 1(eth1) entered forwarding state
<6>[ 8.370000] device br0 left promiscuous mode
<6>[ 8.380000] device br0 entered promiscuous mode
<6>[ 8.390000] Atheros AR8216/AR8236/AR8316 ag71xx-mdio.0:00: Port 5 is up
<3>[ 8.420000] cfg80211: Invalid regulatory domain detected:
<6>[ 8.430000] cfg80211: Regulatory domain: 00
<6>[ 8.430000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time)
<6>[ 8.440000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
<6>[ 8.450000] cfg80211: (2457000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
<6>[ 8.460000] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (N/A, 2000 mBm), (N/A)
<6>[ 8.470000] cfg80211: (5170000 KHz - 5250000 KHz @ 80000 KHz), (N/A, 2000 mBm), (N/A)
<6>[ 8.480000] cfg80211: (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 2000 mBm), (N/A)
<6>[ 8.480000] cfg80211: (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 0 mBm), (N/A)
<6>[ 8.500000] cfg80211: World regulatory domain updated:
<6>[ 8.510000] cfg80211: DFS Master region: unset
<6>[ 8.510000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time)
<6>[ 8.520000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
<6>[ 8.530000] cfg80211: (2457000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
<6>[ 8.540000] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (N/A, 2000 mBm), (N/A)
<6>[ 8.550000] cfg80211: (5170000 KHz - 5250000 KHz @ 80000 KHz), (N/A, 2000 mBm), (N/A)
<6>[ 8.550000] cfg80211: (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 2000 mBm), (N/A)
<6>[ 8.560000] cfg80211: (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 0 mBm), (N/A)
<6>[ 8.570000] cfg80211: Regulatory domain changed to country: CA
<6>[ 8.580000] cfg80211: DFS Master region: FCC
<6>[ 8.580000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time)
<6>[ 8.590000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 3000 mBm), (N/A)
<6>[ 8.600000] cfg80211: (5170000 KHz - 5250000 KHz @ 80000 KHz), (N/A, 1700 mBm), (N/A)
<6>[ 8.610000] cfg80211: (5250000 KHz - 5330000 KHz @ 80000 KHz), (N/A, 2400 mBm), (N/A)
<6>[ 8.610000] cfg80211: (5490000 KHz - 5730000 KHz @ 80000 KHz), (N/A, 2400 mBm), (N/A)
<6>[ 8.620000] cfg80211: (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 3000 mBm), (N/A)
<6>[ 10.360000] br0: port 1(eth1) entered forwarding state
<6>[ 15.910000] device ath0 entered promiscuous mode
<5>[ 16.190000] random: hostapd urandom read with 29 bits of entropy available
<6>[ 16.220000] br0: port 2(ath0) entered forwarding state
<6>[ 16.220000] br0: port 2(ath0) entered forwarding state
<6>[ 16.290000] device br0 left promiscuous mode
<6>[ 16.820000] device eth0 entered promiscuous mode
<6>[ 17.230000] PPP generic driver version 2.4.2
<6>[ 17.340000] PPP BSD Compression module registered
<6>[ 17.360000] PPP Deflate Compression module registered
<6>[ 17.430000] PPP MPPE Compression module registered
<6>[ 17.450000] NET: Registered protocol family 24
<4>[ 17.700000] ipt_TRIGGER: module license 'unspecified' taints kernel.
<4>[ 17.710000] Disabling lock debugging due to kernel taint
<6>[ 18.200000] eth0: link down
<6>[ 18.210000] device eth0 left promiscuous mode
<6>[ 18.220000] br0: port 2(ath0) entered forwarding state
<6>[ 19.430000] eth0: link up (1000Mbps/Full duplex)
<6>[ 37.000000] nf_conntrack: automatic helper assignment is deprecated and it will be removed soon. Use the iptables CT target to attach helpers instead.
<5>[ 40.020000] random: nonblocking pool is initialized
<6>[ 2378.860000] device ath0.sta1 entered promiscuous mode
<6>[ 2378.870000] br0: port 3(ath0.sta1) entered forwarding state
<6>[ 2378.870000] br0: port 3(ath0.sta1) entered forwarding state
<6>[ 2380.870000] br0: port 3(ath0.sta1) entered forwarding state

Detection
DD-WRT User

Joined: 19 Jan 2012
Posts: 403
Location: UK

Posted: Wed Dec 02, 2015 11:25 Post subject:
Access Restrictions website and keyword blocking still not working on WRT160NL although it states as being fixed in this build _________________ TPLINK TL-WR2543ND (5GHz) WRT160NL (2.4GHz)

KrypteX
DD-WRT Guru

Joined: 18 Jan 2014
Posts: 2411

Posted: Wed Dec 02, 2015 11:38 Post subject:

Detection wrote:

Access Restrictions website and keyword blocking still not working on WRT160NL although it states as being fixed in this build

Here are the related tickets. Reopen if necessary:
http://svn.dd-wrt.com/ticket/4942
http://svn.dd-wrt.com/ticket/4811

mwbuss8 wrote:

Router Model:TP-Link Archer C7 v2
Errors: ath1 rate displays 1.08308e+06 Gb/s on the system info page. I know its an ongoing error, but it has changed from previously showing 450 Mb/s as it has since I started using dd-wrt almost a year ago.

Found the problem, it's caused by a typo: http://svn.dd-wrt.com/ticket/4957#comment:5
_________________
THERE ARE NO STRANGERS HERE; ONLY FRIENDS YOU HAVEN'T YET MET.
________________________________________________________________________________________________________
DD-WRT CHANGELOG | DEVICES | DD-WRT BUILDS | KONG BUILDS | UNOFFICIAL BUILDS | DD-WRT in VIRTUALBOX

mrjcd
DD-WRT Guru

Joined: 31 Jan 2015
Posts: 6290
Location: Texas

Posted: Wed Dec 02, 2015 13:34 Post subject:

mrjcd wrote:

WRT160NL x3
DD-WRT v3.0-r28397 std (12/01/15)
Linux 3.10.93 #12506 Tue Dec 1 02:32:51 CET 2015 mips
No Reset -- update all 3 live from 28320

Two as WDS bridge.
One is WAP + guests network.
Updated WDS-AP and then station and WAP across WDS bridge.
Working ok with uptime --- only few minutes
No uglies lurking in the logs.

This error only shows in the WDS-AP.
root@160NL-WDS-South:~# uptime
07:25:48 up 19:25, load average: 0.00, 0.01, 0.04
root@160NL-WDS-South:~# dmesg | tail
<6>[ 225.130000] br0: port 4(ath0.sta1) entered forwarding state
<6>[ 227.130000] br0: port 4(ath0.sta1) entered forwarding state
<6>[ 370.330000] nf_conntrack: automatic helper assignment is deprecated and it will be removed soon. Use the iptables CT target to attach helpers instead.
<3>[ 1641.950000] ath: phy0: DMA failed to stop in 10 ms AR_CR=0x00000024 AR_DIAG_SW=0x42100020 DMADBG_7=0x000084c0
<3>[42211.580000] ath: phy0: DMA failed to stop in 10 ms AR_CR=0x00000024 AR_DIAG_SW=0x42100020 DMADBG_7=0x000286c0
<3>[42777.050000] ath: phy0: DMA failed to stop in 10 ms AR_CR=0x00000024 AR_DIAG_SW=0x42100020 DMADBG_7=0x000042c0
<3>[43077.480000] ath: phy0: DMA failed to stop in 10 ms AR_CR=0x00000024 AR_DIAG_SW=0x42100020 DMADBG_7=0x000084c0
<3>[59391.720000] ath: phy0: DMA failed to stop in 10 ms AR_CR=0x00000024 AR_DIAG_SW=0x42100020 DMADBG_7=0x000084c0
<3>[61935.330000] ath: phy0: DMA failed to stop in 10 ms AR_CR=0x00000024 AR_DIAG_SW=0x42100020 DMADBG_7=0x000084c0
<3>[66867.820000] ath: phy0: DMA failed to stop in 10 ms AR_CR=0x00000024 AR_DIAG_SW=0x42100020 DMADBG_7=0x000042c0

The WDS-Station and the WAP+guest are clean.
All are working ok --

edit:-- WDS bridge is only a bridge -- NO other wireless clients connected to WDS-AP, NO VAP on Station

Argorr
DD-WRT Novice

Joined: 28 Sep 2015
Posts: 38

Posted: Wed Dec 02, 2015 13:52 Post subject:

Router: TL-WDR4300V1
Firmware: 28397
Status: OK
Reset: No
Errors: Didn't reset on initial flash and everything seemed alright. Decided to factory defaults to see if the dhcp forwarding bug was still there. After the factory reset both 2.4 and 5 GHz don't broadcast. Not until i reconfigure the wireless and reboot the router does it start working again. When it does start working the 2.4 ghz works right away but he 5ghz takes several minutes to show up. Also I've noticed that the lan side seems slow. I have a ps3 hard-wired that has noticeable loading times now streaming hulu/Netflix that it didn't before. I can post dmesg when I'm out of work if thats needed.

rozwell
DD-WRT Novice

Joined: 02 Dec 2015
Posts: 33
Location: Poland

Posted: Wed Dec 02, 2015 14:49 Post subject:
Router Model: TL-WR1043NDv2 Firmware: DD-WRT v3.0-r28397 std Status: ok Reset: yes, to default settings Errors: nothing yet

bairam
DD-WRT Novice

Joined: 11 Nov 2014
Posts: 38

Posted: Wed Dec 02, 2015 16:46 Post subject:
Router Model: TP-Link TL-WR841ND v8.1 Status: OK Reset: NO Errors: Not yet noticed

h8red
DD-WRT Guru

Joined: 28 Jun 2011
Posts: 580
Location: Vilnius, Lithuania

Posted: Wed Dec 02, 2015 17:20 Post subject:
Router: TP-Link TL-WR842ND v2 Firmware: DD-WRT v3.0-r28397 Kernel: Linux 3.10.93 #12562 Status: OK Reset: no Errors: no Web upgrade from r28366 _________________ [Ramips] Nexx WT3020F Openwrt @kernel #4.14.167 (OpenVPN server, Wireguard server, AD blocking, SQM QOS, USB)

Goto page Previous 1, 2, 3 Next

Display posts from previous:

Page 2 of 3

DD-WRT Forum Index -> Atheros WiSOC based Hardware

All times are GMT

Navigation

Jump to:

You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
You cannot attach files in this forum
You cannot download files in this forum

Log in

New Build - 12/01/2015 - r28397

Quick Links

Log in