Posted: Fri Feb 07, 2020 4:20 Post subject: EA6350 V2
Guys,
Take a looks at page 22 of this thread. I had the exact same issue you guys are facing. The person who posted about updating to the latest linksys firmware and then straight to DD-wrt, I believe is a V1 hardware. The flash would work for a little while but then after a reboot it would revert back. For the V2 hardware of the EA6350 that I am currently using, you must hook up a serial cable to the pinout on the motherboard. Page 22 of this thread breaks down my experience with flashing dd-wrt on my EA6350. Overall, I'm very happy that I did flash dd-wrt. It's been way better that the stock FW. Also due warning, there's no reverting back to stock after you're on DD-wrt. At least no method that I have found.
Good luck !
I'm here if you have questions or need an old KONG fw file. _________________ WRT54GL v1.1 - Flashed
Linksys WRT54G2 v1 - Flashed
EA6350 v2 - Flashed
Posted: Sat Feb 08, 2020 3:11 Post subject: EA6350 V2
It Looks like the wikidevi site was taken down. But I looked through the archives and found the EA6350 pinout. see attached. I hope this helps. Good luck !!
Please re-read this thread in it's entirety to figure out how to install DD-WRT on the EA6350.
...or someone that knows how, can write a Install Guide and/or wiki.
Because reading 26 pages (and growing), half of it not pertaining to you, is a good day spent.
It's like the old Linux saying:
Linux is the best OS!!!! as long as you can spend 6 months reading forums, just to figure out how to turn up the volume.
Joined: 08 May 2018 Posts: 8120 Location: Texas, USA
Posted: Sun Apr 12, 2020 6:27 Post subject:
EDITED: Yes, I agree that this thread is cumbersome. I will see what I can do to compile the information in the thread to pass on to the other moderator(s) who have wiki access to populate this page: https://wiki.dd-wrt.com/wiki/index.php/Linksys_EA6350.
ADD: I have posted in the moderator forum to see about locking this thread temporarily to clean it up and get the information sorted out.
EDITED: Yes, I agree that this thread is cumbersome. I will see what I can do to compile the information in the thread to pass on to the other moderator(s) who have wiki access to populate this page: https://wiki.dd-wrt.com/wiki/index.php/Linksys_EA6350
I don't think new devices pages are really necessary, since the procedures for all these are basically the same, right? Other than the 6350v2 that is, which is not in the supported list but can be flashed via serial?
Is all that is needed to properly support it is for BS to add the board id? Looks like lots of these models all use the EA6350 build already.
I will update the EA6400 wiki to mention which files to use for the appropriate model.
I have already updated the Supported Devices wiki to point the EA6xxx devices to the appropriate threads, afaik:
EA6300, EA6350v1, and EA6400 point to EA6400 wiki
EA6500 and EA6700 point to EA6700
EA6900 points to EA6900 (unchanged)
Should I update Supported Devices to add the 6350v2, and point to the serial flash thread, or just mention it in the wiki (at least until and if BS adds the support, if its easy). _________________ #NAT/SFE/CTF: limited speed w/ DD#Repeater issues#DD-WRT info: FAQ, Builds, Types, Modes, Changes, Demo#
x64 OPNsense 20.7.6|FT2020.6: EA6900v1.1@1GHz, F7D8302@532|DD 45036: DIR-810L, WNDR4500v2 & 4000@533,
R6300v1, RT-N66U@663, E1500@353, WRT54G{Lv1.1,Sv6}@250|OpenWRT 19.7.5: RT-ACRH13, R6220, WNDR3700v4
Joined: 08 May 2018 Posts: 8120 Location: Texas, USA
Posted: Sun Apr 12, 2020 19:57 Post subject:
And who's names are in the comments?
@imWACCo: If you could use the serial method of flashing and give us a dump of the CFE boot log before you flash one of each in text files and attach them to the ticket, that would be awesome! Just a small request...
If you could use the serial method of flashing and give us a dump of the CFE boot log before you flash one of each in text files and attach them to the ticket, that would be awesome! Just a small request...
Well, no and yes. I've not seen my TTL cable in... 8?... years. Just ordered one from Am Prime, should be here in two days.
I got a bunch of different N/AC routers for free. It seems like every one of the %&#@ things need TTL
kernel-panic69, what can I do to help? sorry for the mess on this thread. I have a spare EA6350 V2 not currently using it, and I can get whatever is needed for this. _________________ WRT54GL v1.1 - Flashed
Linksys WRT54G2 v1 - Flashed
EA6350 v2 - Flashed
Joined: 08 May 2018 Posts: 8120 Location: Texas, USA
Posted: Sun Apr 12, 2020 22:39 Post subject:
@technoside2, imWACCo: Pretty much an entire serial boot log from stock firmware, preferably. Attach to this ticket: https://svn.dd-wrt.com/ticket/6529