Author
Message
TheLizard DD-WRT Novice Joined: 07 Apr 2012 Posts: 3
Posted: Sat Apr 07, 2012 14:31 Post subject: NetGear WGR614v6 2MB how to JTAG
I have got a NetGear WGR614v6 with a 2MB flash, I have soldered in some wires (for JTAG), even done the reset button fix.
I have ordered an JTAG programmer through ebay, but I am puzzled about the connections from the board to the JTAG programmer.
The Pinout of the board is:
TRST, TDI, TDO, TMS, TCK, SRST and some GND from somewhere....
The JTAG pinout I have is TDI, TDO, TMS, TCK and VREF...
1) Where do I put the TRST, SRST and VREF signals?
2) I have downloaded a CFE, guess I will manage to program it in, but which revision of the DD-WRT Micro should I put into?
3) When it all works and I would like to upgrade the hardware (other flash and ram), what sizes should I take to make it work?
--
If anyone would like to know anything about this thing while it is still 'untouched' (software-wise), please let me know.
Thanks in advance!
TheLizard
Back to top
Sponsor
barryware DD-WRT Guru Joined: 26 Jan 2008 Posts: 13049 Location: Behind The Reset Button
Posted: Sat Apr 07, 2012 15:52 Post subject:
an unbuffered cable does not use TRST or SRST
only TDI, TDO, TMS, TCK, & GND _________________[Moderator Deleted]
Back to top
TheLizard DD-WRT Novice Joined: 07 Apr 2012 Posts: 3
Posted: Sat Apr 14, 2012 18:55 Post subject:
I have received my USB blaster and soldered the required wires, the altera programmer software can find a device in the jtag chain.
How do I proceed to program the flash on the board?
Back to top
barryware DD-WRT Guru Joined: 26 Jan 2008 Posts: 13049 Location: Behind The Reset Button
Posted: Sat Apr 14, 2012 20:23 Post subject:
TheLizard wrote: I have received my USB blaster and soldered the required wires, the altera programmer software can find a device in the jtag chain.
How do I proceed to program the flash on the board?
you need to contact the author of your software & jtag hardware. _________________[Moderator Deleted]
Back to top
TheLizard DD-WRT Novice Joined: 07 Apr 2012 Posts: 3
Posted: Mon Apr 23, 2012 19:39 Post subject:
I have managed to backup the flash using JTAG and OpenOCD (Anyone interested in the procedure, please ask...)
Currenly flashing a CFE (modified my own mac addresses in)
Which (micro) revision of DD-WRT should I put into it?
Back to top
se505er DD-WRT Novice Joined: 09 Apr 2008 Posts: 17
Posted: Fri Jun 05, 2015 8:49 Post subject: How to flash with Altera USB-Blaster ?
I did by an Altera USB-Blaster, but I get no Hardware detected with qprogrammer and I get the message
"Warning: TDO seems to be stuck at 1" with UrJTAG even with puted Pin nTRST to +5V.
(With the old wiggler-LPT1-PC "tjtagv2 -flash:cfe /noemw /noreset" did work fine).
I do not know anything about using openocd and how usb-jtag.cfg, altera-usb-blaster.cfg and
board/se505.cfg should look like so could you please, please give as much detailed description
of the procrdure as possible ?
Back to top