Your reports for Broadcom units are highly appreciated !
Router:
Firmware:
Kernel:
Status:
Reset:
Errors:
This build thread is for reporting successes and problem with loading this experimental test build. This is important info for developers and users. Always state your hardware and SPECIFIC build. (eg: 27119_NEWD-2_K2.6_mega-nv64k.bin). Do not ask questions about your specific router or how to configure it in this thread; create your own thread to discuss any specific problems you have or need resolved. This thread is to report info, not to seek it. Posts that do not add to understanding this build will be deleted. Make sure you know how to flash properly and the risk before using this build. It is important to adhere to these requirements, to keep this thread from becoming impossibly long and useless. If you don't know what build to flash and how to flash properly and have a means of recovery if things should go wrong, do NOT flash this experimental test build. _________________ THERE ARE NO STRANGERS HERE; ONLY FRIENDS YOU HAVEN'T YET MET.
________________________________________________________________________________________________________
DD-WRT CHANGELOG | DEVICES | DD-WRT BUILDS | KONG BUILDS | UNOFFICIAL BUILDS | DD-WRT in VIRTUALBOX
Last edited by KrypteX on Tue Jun 16, 2015 7:19; edited 6 times in total
Router: Archer C9
Firmware: 27119
Status: Working
Reset: No
Errors: None
Previous: 27096
LAN led not working.
When i enable JFFS2 Support, partition mtdblock3 is mounted on /jffs/. Everything is OK, but when I reboot router it starts with the factory settings and JFFS2 Support is disable.
dmesg:
[...]Creating 6 MTD partitions on "bcmsflash":
0x000000000000-0x000000040000 : "boot"
0x000000040000-0x000000ff0000 : "linux"
0x0000001c0000-0x000000d70000 : "rootfs"
0x000000d70000-0x000000ff0000 : "ddwrt"
0x000000ff0000-0x000001000000 : "nvram_cfe"
0x000000fe0000-0x000000ff0000 : "nvram"
nflash: found no supported devices[...]
Flashed two E3000 with dd-wrt.v24-27119_NEWD-2_K2.6_big-nv60k.bin and one E4200 V1 with dd-wrt.v24-27119_NEWD-2_K3.x_mega-e4200.bin (no reset). So far they seem to work ok. _________________ 2 times APU2 Opnsense 21.1 with Sensei
2 times RT-AC56U running DD-WRT 45493 (one as Gateway, the other as AP, both bridged with LAN cable)
3 times Asus RT-N16 shelved
E4200 V1 running freshtomato 2020.8 (bridged with LAN cable)
3 times Linksys WRT610N V2 converted to E3000 and 1 original E3000 running freshtomato 2020.8 (bridged with LAN cable)
Router: Archer C9
Firmware: 27119
Status: Working
Reset: No
Errors: None
Previous: 27096
LAN led not working.
When i enable JFFS2 Support, partition mtdblock3 is mounted on /jffs/. Everything is OK, but when I reboot router it starts with the factory settings and JFFS2 Support is disable.
dmesg:
[...]Creating 6 MTD partitions on "bcmsflash":
0x000000000000-0x000000040000 : "boot"
0x000000040000-0x000000ff0000 : "linux"
0x0000001c0000-0x000000d70000 : "rootfs"
0x000000d70000-0x000000ff0000 : "ddwrt"
0x000000ff0000-0x000001000000 : "nvram_cfe"
0x000000fe0000-0x000000ff0000 : "nvram"
nflash: found no supported devices[...]
Any Chance BrainSlayer can tune up the next build and slim it down just a touch?
Another error I am trying to chase down: Working from a new Windows 8.1 laptop, and the javascript:OpenAboutWindow() call is not working. It causes a stop working window to pop up for IE11. I thought it worked for previous versions, but I have not confirmed it.
Same problem with last couple builds on E2500 dd-wrt.v24-27119_NEWD-2_K3.x_mega-e2500.bin
Won't install file... sz = 8,037,376 byte
And this crazy build puts a E2500 into firmware management mode every time.
tried on three E2500 all different previous mini builds.
k3-E2500-27119 is even bigger than last build
Posted: Sun May 31, 2015 5:40 Post subject: Updated to 27119 but status still shows 26497?
Every release after 26497 I've upgraded to still shows the firmware as 26497, is this a glitch or is it not being updated even though it is being reported as successful?
