New build --- 26854 --- 05/07/2015

Post new topic   Reply to topic    DD-WRT Forum Forum Index -> Broadcom SoC based Hardware
Author Message
KrypteX
DD-WRT Guru


Joined: 18 Jan 2014
Posts: 2411

PostPosted: Thu May 07, 2015 12:42    Post subject: New build --- 26854 --- 05/07/2015 Reply with quote
New build 26854 - 05/07/2015 available: ftp://ftp.dd-wrt.com/betas/2015/05-07-2015-r26854/

Selected changelog (since 26839) from http://www.dd-wrt.com/phpBB2/viewtopic.php?t=279467 :

Your reports for Broadcom units are highly appreciated !
Router:
Firmware:
Kernel:
Status:
Reset:
Errors:

This build thread is for reporting successes and problem with loading this experimental test build. This is important info for developers and users. Always state your hardware and SPECIFIC build. (eg: 26854_NEWD-2_K2.6_mega-nv64k.bin). Do not ask questions about your specific router or how to configure it in this thread; create your own thread to discuss any specific problems you have or need resolved. This thread is to report info, not to seek it. Posts that do not add to understanding this build will be deleted. Make sure you know how to flash properly and the risk before using this build. It is important to adhere to these requirements, to keep this thread from becoming impossibly long and useless. If you don't know what build to flash and how to flash properly and have a means of recovery if things should go wrong, do NOT flash this experimental test build.

_________________
THERE ARE NO STRANGERS HERE; ONLY FRIENDS YOU HAVEN'T YET MET.
________________________________________________________________________________________________________
DD-WRT CHANGELOG | DEVICES | DD-WRT BUILDS | KONG BUILDS | UNOFFICIAL BUILDS | DD-WRT in VIRTUALBOX

Testing BrainSlayer's DD-WRT build 31924 on various units:
NETGEAR : WNDR3800 WNDR3800CH WNDRMACv2 WNDRMACv1 WNR2200 WNR2000v3
TP-LINK : ArcherC7v3 WR1043NDv3 WR740Nv4 WR740Nv6 WR710Nv1 WR810Nv1 WA850REv1 WA901NDv3 WA901NDv4
D-LINK : DIR-862L DIR-615D2
ASUS : RT-N10 C1
VirtualBox : x86_64


Last edited by KrypteX on Fri May 22, 2015 8:25; edited 4 times in total
Sponsor
cannedchaos
DD-WRT Novice


Joined: 16 Dec 2014
Posts: 39

PostPosted: Thu May 07, 2015 13:55    Post subject: DIR868L misdetection Reply with quote
So trac signup is broken and I cannot report this.
The LED/USB bug present in recent builds of the D-Link DIR868L appears to be caused by a bug in the router identification code.
This appears to have been introduced in SVN rev 26520:

src/router/libutils/utils.c, line 1177 contains:
Code:
 if (boardnum == 24 && nvram_match("boardtype", "0x0646")
&& nvram_match("boardrev", "0x1110")
&& nvram_match("gpio7", "wps_button") && nvram_match("gpio6", "wps_led") && nvram_get("pci/1/1/venid")) {
setRouter("Dlink-DIR868L");
return ROUTER_DLINK_DIR868;
 }

The nvram_match("gpio6", "wps_led") used to have a "!" in front of it. And indeed, on my router "get nvram gpio6" returns nothing. This would mean the system fails to see the router as a DIR868L and defaults to a generic broadcom northstar device.

I am also not sure about the last check for nvram_get("pci/1/1/venid")) (does it evaluate as true if it returns any non-zero value?) but "nvram get pci/1/1/vendid" on my router returns 0x14E4.

Could someone please fix this or report it in the SVN for me?
mrjcd
DD-WRT Guru


Joined: 31 Jan 2015
Posts: 5103
Location: Texas

PostPosted: Thu May 07, 2015 14:24    Post subject: Reply with quote
E2500
[dd-wrt.v24-26854_NEWD-2_K2.6_big-nv60k.bin]
DD-WRT v24-sp2 (05/07/15) big - build 26854
Linux 2.6.24.111 #25277 Thu May 7 02:20:35 CEST 2015 mips
reset - previous
DD-WRT v24-sp2 (01/20/15) mega - build 25974
Linux 2.6.24.111 #23549 Tue Jan 20 04:11:09 CET 2015 mips

Using NG-Mixed Repeater Bridged to WNDR3700v4 (build 26849), WPA2-AES, wide HT40
Connected at 300 Mbs
Can ONLY connect to VAP with security disabled or using WEP security on VAP.
Mac addresses seem to be all in order with this build.
'bout all I know
b0f
DD-WRT Novice


Joined: 03 Apr 2014
Posts: 26

PostPosted: Thu May 07, 2015 17:34    Post subject: Reply with quote
Router Model: Linksys E4200
Status: working
Reset: No
Errors: No
miles01
DD-WRT Novice


Joined: 09 Dec 2006
Posts: 48

PostPosted: Thu May 07, 2015 23:34    Post subject: DIR-890L Reply with quote
Router Model: DIR-890L
Status: OK
Reset: NO
Errors: NO

WDS between two DIR-890L with 1st AC interface
I select ac-Only at 80mhz but the channel not available and stay at 36.
and I have a problem with type B IP a DHCP out of nowhere gave me a 192.168.<0>.XXX address.
At this time they do a very good JOB.
DLNA, smb, and DNS is working


Wink
SteveJenkins
DD-WRT User


Joined: 04 Dec 2012
Posts: 126
Location: Seattle, WA

PostPosted: Fri May 08, 2015 0:12    Post subject: Reply with quote
I've noticed in the past few builds that the commands interface doesn't seem to work.

These commands work fine from the shell, but when I attempt to run them in the GUI, I get the following, which is basically a complaint that it didn't like the command.

So somehow commands via the GUI are being interpreted differently than if I just typed them from the command line.



BTW, are these bugs tracked? Or should I create a ticket?

P.S. This is on an E4200 v1.

_________________

My Max-Speed DD-WRT settings | K2.6 vs K3.x Speeds Head to Head | My Overclocking Settings | My blog: SteveJenkins.com | My Job: CheatCodes.com
jrscs
DD-WRT User


Joined: 09 Aug 2010
Posts: 237

PostPosted: Fri May 08, 2015 1:52    Post subject: Reply with quote
Build 26854 - Previous 26839

RT-AC68R - primary router/gateway
asus_rt-ac68u-firmware.trx
2.4Ghz (NG-mixed) with 40Mhz channel width: OK
5Ghz (Mixed) with 80Mhz channel width: OK
Guest-Vlan 2.4Ghz: OK
SSH: OK
Telnet: OK
Port Forward: OK
WOL over the Internet: OK
VNC Repeater: OK
USB 2.0 storage ext3 mount to JFFS: OK
USB 3.0 storage NTFS mount to MNT: OK
NAS Samba shared drive: OK
PPTP Server: OK
Wi-viz 2.4Ghz & 5Ghz: OK
Power Up Reset: Yes (before and after flash)
Status: Working
Errors: OK

RT-AC66U - primary router/gateway
dd-wrt-26854-Asus_RT-AC66.trx
2.4Ghz (NG-mixed) with 40Mhz channel width: OK
5Ghz (Mixed) with 80Mhz channel width: OK
Guest-Vlan 2.4Ghz: OK
SSH: OK
Telnet: OK
Port Forward: OK
WOL over the Internet: OK
USB storage ext3 mount to JFFS: OK
USB storage NTFS mount to MNT: OK
NAS Samba shared drive: OK
PPTP Server: OK
Wi-viz 2.4Ghz & 5Ghz: OK
Power Up Reset: No (before and after flash), will reset 5.0 GHz radio to 2.4 GHz radio
Status: Working
Errors:
*** Builds after 26339 when erasing NVRAM in telnet session or Power UP Reset, resets 5.0 GHz radio to 2.4 GHz radios – To recover return to 26339 ***
*** Builds after 26339 use the GUI to reset NVRAM to Factory Defaults ***

Repeater Bridge(s) Build 26854 - Previous 26653

e4200 – Repeater Bridge on 5 Ghz (N) to RT-AC68R
dd-wrt.v24-26854_NEWD-2_K3.x_mega-e4200.bin
2.4Ghz (NG-mixed) with 20Mhz channel width: OK
5Ghz (N): OK
30/30/30 Reset: Yes (before and after flash)
Status: Working
Errors: OK

_________________
Asus AC87U A1 - DD-WRT v3.0-r41418 std (10/30/19)
Repeater Bridges(s)
Asus AC68R A1 - DD-WRT v3.0-r41418 std (10/30/19)
Netgear R6400 V2 - DD-WRT v3.0-r41418 std (10/30/19)
Asus AC66U A1 - DD-WRT v3.0-r41418 giga (10/30/19)
james1795
DD-WRT User


Joined: 11 Jan 2011
Posts: 160

PostPosted: Fri May 08, 2015 11:56    Post subject: EA6900 Reply with quote
Router: EA6900
Firmware: 05-07-2015-26854
Status: Working
Reset: No
Errors: None
Previous: 05-06-2015-r26839


Update via Interface. Working well, hopefully wont require me to telnet and push it that way.
slobodan
DD-WRT Guru


Joined: 03 Nov 2011
Posts: 1551
Location: Zwolle

PostPosted: Sat May 09, 2015 0:53    Post subject: Reply with quote
Flashed two E3000 with dd-wrt.v24-26854_NEWD-2_K2.6_big-nv60k.bin and an E4200 V1 with
dd-wrt.v24-26854_NEWD-2_K3.x_mega-e4200.bin (no reset). They appear to be working ok.

_________________
2 times RT-AC56U running 33772 with entware-ng, Yamon 3 (SFE disabled).

Asus RT-N16 running Merlin LTS fork RT-N16_3.0.0.4_374.43_2-25E8j9527.trx with entware-ng.

2 times Asus RT-N16 running dd-wrt.v24-33772_NEWD-2_K3.x_big.bin with entware-ng

E4200 V1 running dd-wrt.v24-33772_NEWD-2_K3.x_mega-e3000.bin

3 times Linksys WRT610N V2 converted to E3000 and 1 original E3000 running dd-wrt.v24-33772_NEWD-2_K3.x_mega-e3000.bin (bridged with LAN cable)

n1ghtwish
DD-WRT Novice


Joined: 22 Feb 2015
Posts: 12

PostPosted: Sat May 09, 2015 1:10    Post subject: Reply with quote
Router Model: Netgear WNDR4500v2
Status: OK
Reset: YES
Errors: See below...

Upgraded from 26405 initially without reset. Browser and the little timer hung about 10 seconds into upgrade. Rebooted router, ended up with a soft brick (solid amber WAN light, green blinking power light). 30/30/30'd, TFTP'd back to stock, flashed 26138, then upgraded to 26854 (with reset) successfully.

Running --
MiniDLNA
PPTP
VAP
Transmission
USB/NAS
DDNS
QoS (seems to be working fine at this time)
Port Forwarding
Display posts from previous:    Page 1 of 1
Post new topic   Reply to topic    DD-WRT Forum Forum Index -> Broadcom SoC based Hardware All times are GMT

Navigation

 
Jump to:  
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
You can attach files in this forum
You can download files in this forum